DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.

For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.

The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove two unused WB functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change omapdrm to get dispc_ops and use that to call the dispc functions
instead or direct function calls.

The change is very straightforward.

The only problem was in omap_crtc_init() which calls pipe2vbl(crtc), and
at that point of time the crtc->dev link, which is used to get the
dispc_ops, has not been set up yet. This patch makes omap_crtc_init()
skip the call to pipe2vbl() and instead calls
dispc_ops->mgr_get_vsync_irq() directly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.

This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and  dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.

Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.

This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

display.c uses dsi_get_pixel_size() which is implemented in the DSI
driver, and we won't have that in the omapdss-base module, to which we
want to move display.c

This patch changes display.c not to use dsi_get_pixel_size(). The call
can be replaced with a simple check for OMAP_DSS_DSI_FMT_RGB565.

We can also make dsi_get_pixel_size() static as it's no longer used
outside dsi.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't have omapdss's custom error printing functions in the common
omapdss-base module, to which we want to move output.c.

This patch changes output.c to use dev_err instead of DSSERR so that it
doesn't depend on DSSERR.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are working towards enabling omapdss6, which will consists of a new
dss, dispc and dpi drivers. omapdss6 will be a new module. The panel,
encoder and omapdrm will need to use either the current omapdss driver
or the new omapdss6 driver, depending on the platform.

This will be implemented with a common base module and function
pointers.

This patch adds a skeleton omapdss-base.ko module, to which we'll be
moving common dss functionality like registration of the panels.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

While implementing writeback support, odd behavior of WBDELAYCOUNT was
observed with the combination of WB capture and HDMI. The result of the
debugging was that the HDMI sync polarities are not set correctly.

The current code sets the sync polarities going from HDMI WP to DISPC
according to the video mode used, which seems to work normally fine, but
causes problems with WB as WB expects the syncs to be active-high.

This patch changes the HDMI sync polarities so that the DISPC always
gets active-high syncs from HDMI WP, and the HDMI core gets sync
polarities according to the used video mode.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Add support for render nodes in omap driver and allow required
ioctls to be accessible via render nodes.

This enables unprivileged clients to allocate resources like GEM buffers
for rendering their content into. Mode setting (KMS ioctls) is not
allowed using render nodes. These buffers are then shared with
a previleged process (e.g compositor) that has mode setting access.

An example of this use case is Android where the hardware composer is
the only master and has mode setting access. Every other client then
uses render node(e.g /dev/dri/renderD128 to allocate and use its buffers.
Signed-off-by: NHemant Hariyani <hemanthariyani@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The clock source selection for the LCD outputs is too hardcoded at the
moment. For example, LCD3 is set to use PLL2_1, and PLL2 doesn't exist
on DRA72x SoCs.

There are quite many ways to configure the clocks, even using HDMI PLL
for LCD outputs, but enabling full configuration of the clocks is rather
tricky.

This patch improves the situation a bit by checking if the PLL about to
be used exists, and if not, tries another one.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

mode_config's min_width and min_height are both set to 32, which is
overly restrictive.

The real limits depend on whether we're configuring a crtc or a plane,
but a limit of 8x2 is safe for both cases.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The driver only uses even dividers for hsdiv when pclk >= 100MHz, as odd
dividers can create uneven duty cycle. However, while this holds true
for some dividers like DISPC's LCK and PCK dividers, it is not actually
true for hsdiv.

hsdiv always produces even duty cycle, so the constraint can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The current driver doesn't expose any of the CRTC HW properties like
background color or transparency key, and sets them at CRTC enable time.

Refactor this into a separate function and call that function from
omap_crtc_atomic_flush(). This is the behavior we want when the
properties can be configured, so this patch makes it easier to add
patches later which implement those properties.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DRA7 errata i886 (FPDLink PLL Unlocks With Certain SoC PLL M/N Values)
says that FPDLink is sensitive to jitter on the vout clock, and that low
PLL M and N values result in more jitter than high M and N values.

This patch implements a workaround for the problem by changing the PLL
setup to search for clocks starting from high M and N values, instead of
low values. This should not cause any functional change, and only
reduces the jitter.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omap_gem_dmabuf_mmap() returns an error (with a WARN) when called for a
buffer which is allocated with dma_alloc_*(). This prevents dmabuf mmap
from working on SoCs without DMM, e.g. AM4 and OMAP3.

I could not find any reason for omap_gem_dmabuf_mmap() rejecting such
buffers, and just removing the if() fixes the limitation.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h>

Fix up affected files that include this signal functionality via sched.h.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Use a more common logging style.

Miscellanea:

o Coalesce formats and realign arguments
o Neaten a few macros now using pr_<level>
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NRob Clark <robdclark@gmail.com>
Acked-by: NSinclair Yeh <syeh@vmware.com>
Acked-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/76355db47b31668bb64d996865ceee53bd66b11f.1488285953.git.joe@perches.com

->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.

Remove the vma parameter to simplify things.

[arnd@arndb.de: fix ARM build]
  Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.comSigned-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Let's disable all scaling that requires horizontal decimation with
higher factor than 4, until we have better estimates of what we can
and can not do. However, NV12 color format appears to work Ok with
all decimation factors.

When decimating horizontally by more that 4 the dss is not able to
fetch the data in burst mode. When this happens it is hard to tell if
there enough bandwidth. Despite what theory says this appears to be
true also for 16-bit color formats.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move drm_atomic_helper_commit_modeset_enables() call to before
drm_atomic_helper_commit_planes() call and have a
omap_atomic_wait_for_completion() call after both.

With the current dss dispc implementation we have to enable the new
modeset before we can commit planes. The dispc ovl configuration
relies on the video mode configuration been written into the HW when
the ovl configuration is calculated.

This approach is not ideal because after a mode change the plane
update is executed only after the first vblank interrupt. The dispc
implementation should be fixed so that it is able use uncommitted drm
state information.  information.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This reverts commit dadf4659.

If planes are not disabled when the they are not on any crtc anymore
they will remain active and may show as "ghosts" when the crtc they
were last on is active again.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers.  For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook.  So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NAlexey Brodkin <abrodkin@synopsys.com>
Acked-by: NLiviu Dudau <liviu.dudau@arm.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org

Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!

v2: Forgot to git add everything :(

v3: Actually remove release_fbi (Sean, Emil, Chris) ...

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch

Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure.  I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.

I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates.  The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.

// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)

@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)

@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>

Changes since v1:
 - Rebased on top of the tip of drm-misc-next.
 - Remove mention to sti since a proper fix got merged.
Suggested-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk

drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so the drm_driver.debugfs_cleanup callback is not
needed.

Cc: tomi.valkeinen@ti.com
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-12-noralf@tronnes.org

Since we need to change the implementation, stop exposing internals.

Provide kref_read() to read the current reference count; typically
used for debug messages.

Kills two anti-patterns:

	atomic_read(&kref->refcount)
	kref->refcount.counter
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But omapdrm is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-4-git-send-email-daniel.vetter@ffwll.ch

The integer returned by the unload hook is ignored by the drm core, so
let's make it void.

This patch was created using the following Coccinelle semantic script
(except for the declaration and comment in drm_drv.h):

Compile-tested only.

// <smpl>
@ get_name @
struct drm_driver drv;
identifier fn;
@@
drv.unload = fn;

@ replace_type @
identifier get_name.fn;
@@
- int
+ void
fn (...)
{
...
}

@ remove_return_param @
identifier get_name.fn;
@@
void fn (...)
{
<...
if (...)
return
- ...
;
...>
 }

@ drop_final_return @
identifier get_name.fn;
@@
void fn (...)
{
...

- return 0;
}
// </smpl>
Suggested-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170106175731.29196-1-krisman@collabora.co.uk

Add module alias for Sony ACX565AKM LCD panel. This makes it probe on Nokia
N900 when panel driver is built as a module.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dsi.c compile fails if PRINT_VERBOSE_VM_TIMINGS is enabled, as the
video timings were not converted in the code behind that ifdef. Note
that PRINT_VERBOSE_VM_TIMINGS has to be enabled by hand, there's no
config option for it.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
[tomi.valkeinen@ti.com: fixed the patch description]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Including all drivers. I thought about keeping small compat functions
to avoid having to change all drivers. But I really like the
drm_printer idea, so figured spreading it more widely is a good thing.

v2: Review from Chris:
- Natural argument order and better name for drm_mm_print.
- show_mm() macro in the selftest.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483009764-8281-1-git-send-email-daniel.vetter@ffwll.ch

The drm driver .load() operation is prone to race conditions as it
initializes the driver after registering the device nodes. Its usage is
deprecated, inline it in the probe function and call drm_dev_alloc() and
drm_dev_register() explicitly.

For consistency inline the .unload() handler in the remove function as
well.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

By linking the sizeof to a variable type the code will be less prone to
bugs due to future type changes of variables.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move the list of pending IRQ wait instances to the omap_drm_private
structure and the wait queue head to the IRQ wait structure.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>