Per RFC6437 stateful flow labels (e.g. labels set by flow label manager)
cannot "disturb" nodes taking part in stateless flow labels. While the
ranges only reduce the flow label entropy by one bit, it is conceivable
that this might bias the algorithm on some routers causing a load
imbalance. For best results on the Internet we really need the full
20 bits.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the meaning of net.ipv6.auto_flowlabels to provide a mode for
automatic flow labels generation. There are four modes:

0: flow labels are disabled
1: flow labels are enabled, sockets can opt-out
2: flow labels are allowed, sockets can opt-in
3: flow labels are enabled and enforced, no opt-out for sockets

np->autoflowlabel is initialized according to the sysctl value.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't call skb_get_hash here since the packet is not complete to do
flow_dissector. Create hash based on flowi6 instead.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add skb_get_hash_flowi6 and skb_get_hash_flowi4 which derive an sk_buff
hash from flowi6 and flowi4 structures respectively. These functions
can be called when creating a packet in the output path where the new
sk_buff does not yet contain a fully formed packet that is parsable by
flow dissector.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: GENET, SYSTEMPORT and DSA netconsole

This patch series adds support for netconsole in the GENET, SYSTEMPORT and DSA
drivers.

A small refactoring to the DSA transmit path is required to avoid duplicating
the dsa_netpoll_send_skb() into each and every tagging protocol supported.

Testing on e.g: mv643xx_eth and/or e1000e would be much appreciated!

Changes in v2:

- properly disable/enable interrupts in GENET and SYSTEMPORT

- pass the reallocated SKB back to dsa_slave_xmit() in case a tag protocol had to
  alter the original SKB
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for using DSA slave network devices with netconsole, which
requires us to allocate and free custom netpoll instances and invoke the
parent network device poll controller callback.

In order for netconsole to work, we need to construct the DSA tag, but
not queue the skb for transmission on the master network device xmit
function.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All tagging protocols do the same thing: increment device statistics,
make room for the tag to be inserted, create the tag, invoke the parent
network device transmit function.

In order to prepare for adding netpoll support, which requires the tag
creation, but not using the parent network device transmit function, do
some little refactoring which eliminates duplication between the 4
tagging protocols supported.

We need to return a sk_buff pointer back to the caller because the tag
specific transmit function may have to reallocate the original skb (e.g:
tag_trailer.c) and this is the one we should be transmitting, not the
original sk_buff we were passed.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tlb_dynamic_lb could be set only via sysfs, this patch allows it to be
set via netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
Major changes:

mwifiex:

* add TX DATA Pause support
* add multichannel and TDLS channel switch support

ath10k:

* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The policy in the net driver is to attempt MCDI commands and
then handle any EPERM error codes appropriately when returned
by unprivileged functions.
The ethtool selftest contains some tests which are useful on
an unprivileged function, such as the event queue interrupt
tests, but other tests cannot be performed as the function
does not have the required permissions.

If a test returns -EPERM, act as though the test was not run
and continue.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use vsprintf extension %pI4 instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two vxlan driver flags FLOWBASED and COLLECT_METADATA need to be set to
make use of its new flow mode. The former already exposed. Expose the latter.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
af_mpls: fix undefined reference to ip6_route_output with CONFIG_IPV6=n

This patch series uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. Follows the vxlan drivers usage of
ipv6_stub_impl.ipv6_dst_lookup.

There is no sk in the af_mpls context from where
ipv6_stub_impl.ipv6_dst_lookup is used. sk appears to be needed
to get the namespace 'net' and is optional otherwise. This patch series
changes ipv6_stub_impl.ipv6_dst_lookup to take net argument. sk remains
optional.

v1 - v2: use IS_BUILTIN

v2 - v3: Use new Kconfig option that depends on (IPV6 || IPV6=n) as
	 suggested by Dave. Also uses IS_ERR as suggested by Thomas.

v3 - v4: Include missed case of (MPLS_ROUTING=y && IPV6=m) reported by
         Dave.

v4 - v5: Use ipv6_stub_impl.ipv6_dst_lookup as suggested by Hannes

v5 - v6: protect against null ipv6_stub by statically declaring
	 a ipv6_dst_lookup NOP func
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Undefined reference to ip6_route_output and ip_route_output
was reported with CONFIG_INET=n and CONFIG_IPV6=n.

This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. And wraps affected code under
IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6).
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Reported-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.

All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions

First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.

Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);

RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...

'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Repost patch of driver for LAN7800 family of USB 2.0 & USB 3.0 to Gigabit Ethernet.
- remove module param which can be configurable by standard mechanism.
- remove other module parms except msg_level per review comment.
- update to handle byte swap for statistics structure correctly.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to read the dmesg BPF JIT dump also from a
file instead of the klog buffer. I found this quite useful when going
through some 'before/after patch' logs. It also fixes a regex leak
found by valgrind when no image dump was found.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 6301566e. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:

"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."

http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com

So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Jon Maloy says:

====================
tipc: separate link aggregation from link layer

We continue the work on separating the roles of the link aggregation and
link layers, as well as making code cleanups in general.

This second commit batch focuses on moving the orchestration of link
failover and synchronization to the node level, as well as preparing the
node lock structure for further future impovements. We also make some
changes to message delivery between link and socket layer, in order to
make this mechanism safer and less obscure.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when we extract small messages from a message bundle, or
when many messages have accumulated in the link arrival queue, those
messages are added one by one to the lock protected link input queue.
This may increase contention with the reader of that queue, in
the function tipc_sk_rcv().

This commit introduces a temporary, unprotected input queue in
tipc_link_rcv() for such cases. Only when the arrival queue has been
emptied, and the function is ready to return, does it splice the whole
temporary queue into the real input queue.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the most recent changes, all access calls to a link which
may entail addition of messages to the link's input queue are
postpended by an explicit call to tipc_sk_rcv(), using a reference
to the correct queue.

This means that the potentially hazardous implicit delivery, using
tipc_node_unlock() in combination with a binary flag and a cached
queue pointer, now has become redundant.

This commit removes this implicit delivery mechanism both for regular
data messages and for binding table update messages.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to facilitate future improvements to the locking structure, we
want to make resetting and establishing of links non-atomic. I.e., the
functions tipc_node_link_up() and tipc_node_link_down() should be called
from outside the node lock context, and grab/release the node lock
themselves. This requires that we can freeze the link state from the
moment it is set to RESETTING or PEER_RESET in one lock context until
it is set to RESET or ESTABLISHING in a later context. The recently
introduced link FSM makes this possible, so we are now ready to introduce
the above change.

This commit implements this.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The node lock is currently grabbed and and released in the function
tipc_disc_rcv() in the file discover.c. As a preparation for the next
commits, we need to move this node lock handling, along with the code
area it is covering, to node.c.

This commit introduces this change.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, we have been handling link failover and synchronization
by using an additional link state variable, "exec_mode". This variable
is not independent of the link FSM state, something causing a risk of
inconsistencies, apart from the fact that it clutters the code.

The conditions are now in place to define a new link FSM that covers
all existing use cases, including failover and synchronization, and
eliminate the "exec_mode" field altogether. The FSM must also support
non-atomic resetting of links, which will be introduced later.

The new link FSM is shown below, with 7 states and 8 events.
Only events leading to state change are shown as edges.

+------------------------------------+
|RESET_EVT                           |
|                                    |
|                             +--------------+
|           +-----------------|   SYNCHING   |-----------------+
|           |FAILURE_EVT      +--------------+   PEER_RESET_EVT|
|           |                  A            |                  |
|           |                  |            |                  |
|           |                  |            |                  |
|           |                  |SYNCH_      |SYNCH_            |
|           |                  |BEGIN_EVT   |END_EVT           |
|           |                  |            |                  |
|           V                  |            V                  V
|    +-------------+          +--------------+          +------------+
|    |  RESETTING  |<---------|  ESTABLISHED |--------->| PEER_RESET |
|    +-------------+ FAILURE_ +--------------+ PEER_    +------------+
|           |        EVT        |    A         RESET_EVT       |
|           |                   |    |                         |
|           |                   |    |                         |
|           |    +--------------+    |                         |
|  RESET_EVT|    |RESET_EVT          |ESTABLISH_EVT            |
|           |    |                   |                         |
|           |    |                   |                         |
|           V    V                   |                         |
|    +-------------+          +--------------+        RESET_EVT|
+--->|    RESET    |--------->| ESTABLISHING |<----------------+
     +-------------+ PEER_    +--------------+
      |           A  RESET_EVT       |
      |           |                  |
      |           |                  |
      |FAILOVER_  |FAILOVER_         |FAILOVER_
      |BEGIN_EVT  |END_EVT           |BEGIN_EVT
      |           |                  |
      V           |                  |
     +-------------+                 |
     | FAILINGOVER |<----------------+
     +-------------+

These changes are fully backwards compatible.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The implementation of the link FSM currently takes decisions about and
sends out link protocol messages. This is unnecessary, since such
actions are not the result of any link state change, and are even
decided based on non-FSM state information ("silent_intv_cnt").

We now move the sending of unicast link protocol messages to the
function tipc_link_timeout(), and the initial broadcast synchronization
message to tipc_node_link_up(). The latter is done because a link
instance should not need to know whether it is the first or second
link to a destination. Such information is now restricted to and
handled by the link aggregation layer in node.c
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Link failover and synchronization have until now been handled by the
links themselves, forcing them to have knowledge about and to access
parallel links in order to make the two algorithms work correctly.

In this commit, we move the control part of this functionality to the
link aggregation level in node.c, which is the right location for this.
As a result, the two algorithms become easier to follow, and the link
implementation becomes simpler.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the next commit, we will move link synch/failover orchestration to
the link aggregation level. In order to do this, we first need to extend
the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER,
plus four new events to enter and leave those states.

This commit introduces this change, without yet making use of it.
The node FSM now looks as follows:

                           +-----------------------------------------+
                           |                            PEER_DOWN_EVT|
                           |                                         |
  +------------------------+----------------+                        |
  |SELF_DOWN_EVT           |                |                        |
  |                        |                |                        |
  |              +-----------+          +-----------+                |
  |              |NODE_      |          |NODE_      |                |
  |   +----------|FAILINGOVER|<---------|SYNCHING   |------------+   |
  |   |SELF_     +-----------+ FAILOVER_+-----------+    PEER_   |   |
  |   |DOWN_EVT   |         A  BEGIN_EVT A         |     DOWN_EVT|   |
  |   |           |         |            |         |             |   |
  |   |           |         |            |         |             |   |
  |   |           |FAILOVER_|FAILOVER_   |SYNCH_   |SYNCH_       |   |
  |   |           |END_EVT  |BEGIN_EVT   |BEGIN_EVT|END_EVT      |   |
  |   |           |         |            |         |             |   |
  |   |           |         |            |         |             |   |
  |   |           |        +--------------+        |             |   |
  |   |           +------->|   SELF_UP_   |<-------+             |   |
  |   |   +----------------|   PEER_UP    |------------------+   |   |
  |   |   |SELF_DOWN_EVT   +--------------+     PEER_DOWN_EVT|   |   |
  |   |   |                   A          A                   |   |   |
  |   |   |                   |          |                   |   |   |
  |   |   |        PEER_UP_EVT|          |SELF_UP_EVT        |   |   |
  |   |   |                   |          |                   |   |   |
  V   V   V                   |          |                   V   V   V
+------------+       +-----------+    +-----------+       +------------+
|SELF_DOWN_  |       |SELF_UP_   |    |PEER_UP_   |       |PEER_DOWN   |
|PEER_LEAVING|<------|PEER_COMING|    |SELF_COMING|------>|SELF_LEAVING|
+------------+ SELF_ +-----------+    +-----------+ PEER_ +------------+
       |       DOWN_EVT       A          A          DOWN_EVT     |
       |                      |          |                       |
       |                      |          |                       |
       |           SELF_UP_EVT|          |PEER_UP_EVT            |
       |                      |          |                       |
       |                      |          |                       |
       |PEER_DOWN_EVT       +--------------+        SELF_DOWN_EVT|
       +------------------->|  SELF_DOWN_  |<--------------------+
                            |  PEER_DOWN   |
                            +--------------+
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In many cases the call order when a link is reset goes as follows:
tipc_node_xx()->tipc_link_reset()->tipc_node_link_down()

This is not the right order if we want the node to be in control,
so in this commit we change the order to:
tipc_node_xx()->tipc_node_link_down()->tipc_link_reset()

The fact that tipc_link_reset() now is called from only one
location with a well-defined state will also facilitate later
simplifications of tipc_link_reset() and the link FSM.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.

This change serves as a preparation for the coming commits.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function tipc_link_activate() is redundant, since it mostly performs
settings that have already been done in a preceding tipc_link_reset().

There are three exceptions to this:
- The actual state change to TIPC_LINK_WORKING. This should anyway be done
  in the FSM, and not in a separate function.
- Registration of the link with the bearer. This should be done by the
  node, since we don't want the link to have any knowledge about its
  specific bearer.
- Call to tipc_node_link_up() for user access registration. With the new
  role distribution between link aggregation and link level this becomes
  the wrong call order; tipc_node_link_up() should instead be called
  directly as a result of a TIPC_LINK_UP event, hence by the node itself.

This commit implements those changes.
Tested-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-07-30

Here's a set of Bluetooth & 802.15.4 patches intended for the 4.3 kernel.

 - Cleanups & fixes to mac802154
 - Refactoring of Intel Bluetooth HCI driver
 - Various coding style fixes to Bluetooth HCI drivers
 - Support for Intel Lightning Peak Bluetooth devices
 - Generic class code in interface descriptor in btusb to match more HW
 - Refactoring of Bluetooth HS code together with a new config option
 - Support for BCM4330B1 Broadcom UART controller

Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6fd99094 ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.

RFC 4861, 6.3.4.  Processing Received Router Advertisements
   A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
   and Retrans Timer) may contain a value denoting that it is
   unspecified.  In such cases, the parameter should be ignored and the
   host should continue using whatever value it is already using.

   If the received Cur Hop Limit value is non-zero, the host SHOULD set
   its CurHopLimit variable to the received value.

So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Acked-by: NYOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>