Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 14 3月, 2011 8 次提交
    • A
      xHCI: prolong host controller halt time limit · bdfca502
      由 Andiry Xu 提交于 
      xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears
Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's
too short and often cause dmesg shows "Host controller not halted, aborting
reset." message when rmmod xhci-hcd.

Modify the time limit to comply with xHCI 1.0 specification and prevents the
warning message showing when remove xhci-hcd.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      bdfca502
    • A
      xHCI: Remove redundant variable in xhci_resume() · 019a35f1
      由 Andiry Xu 提交于 
      Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system
resume or the system is hibernated, otherwise leave it be. The variable
old_state is redundant and made an unreachable code path, so remove it.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      019a35f1
    • S
      xhci: Rename variables and reduce register reads. · 518e848e
      由 Sarah Sharp 提交于 
      The xhci_bus_suspend() and xhci_bus_resume() functions are a bit hard to
read, because they have an ambiguously named variable "port".  Rename it
to "port_index".  Introduce a new temporary variable, "max_ports" that
holds the maximum number of roothub ports the host controller supports.
This will reduce the number of register reads, and make it easy to change
the maximum number of ports when there are two roothubs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      518e848e
    • S
      xhci: Rework port suspend structures for limited ports. · 1d5810b6
      由 Sarah Sharp 提交于 
      The USB core only allows up to 31 (USB_MAXCHILDREN) ports under a roothub.
The xHCI driver keeps track of which ports are suspended, which ports have
a suspend change bit set, and what time the port will be done resuming.
It keeps track of the first two by setting a bit in a u32 variable,
suspended_ports or port_c_suspend.  The xHCI driver currently assumes we
can have up to 256 ports under a roothub, so it allocates an array of 8
u32 variables for both suspended_ports and port_c_suspend.  It also
allocates a 256-element array to keep track of when the ports will be done
resuming.

Since we can only have 31 roothub ports, we only need to use one u32 for
each of the suspend state and change variables.  We simplify the bit math
that's trying to index into those arrays and set the correct bit, if we
assume wIndex never exceeds 30.  (wIndex is zero-based after it's
decremented from the value passed in from the USB core.)  Finally, we
change the resume_done array to only hold 31 elements.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
      1d5810b6
    • S
      USB: Fix usb_add_hcd() checkpatch errors. · abc4f9b0
      由 Sarah Sharp 提交于 
      The irq enabling code is going to be refactored into a new function, so
clean up some checkpatch errors before moving it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      abc4f9b0
    • S
      USB: Remove bitmap #define from hcd.h · da13051c
      由 Sarah Sharp 提交于 
      Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header.  include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor.  This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.

Remove the bitmap #define and replace instances of it in the host
controller code.  Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
      da13051c
    • S
      xhci: Remove old no-op test. · 0b8ca72a
      由 Sarah Sharp 提交于 
      The test of placing a number of command no-ops on the command ring and
counting the number of no-op events that were generated was only used
during the initial xHCI driver bring up.  This test is no longer used, so
delete it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      0b8ca72a
    • S
      usb: Always return 0 or -EBUSY to the runtime PM core. · db7c7c0a
      由 Sarah Sharp 提交于 
      The PM core reacts badly when the return code from usb_runtime_suspend()
is not 0, -EAGAIN, or -EBUSY.  The PM core regards this as a fatal error,
and refuses to run anymore PM helper functions.  In particular,
usbfs_open() and other usbfs functions will fail because the PM core will
return an error code when usb_autoresume_device() is called.  This causes
libusb and/or lsusb to either hang or segfault.

If a USB device cannot suspend for some reason (e.g. a hub doesn't report
it has remote wakeup capabilities), we still want lsusb and other
userspace programs to work.  So return -EBUSY, which will fill people's
log files with failed tries, but will ensure userspace still works.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      db7c7c0a
  3. 12 3月, 2011 7 次提交
  5. 10 3月, 2011 3 次提交
  7. 08 3月, 2011 7 次提交
    • L
      ARM: s3c24xx: Switch to common GPIO controlled UDC pullup implementation · e27c3c5c
      由 Lars-Peter Clausen 提交于 
      Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
This patch changes these boards to use the common implementation for GPIO
controlled pullup in the UDC driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      e27c3c5c
    • L
      USB: s3c2410_udc: Add common implementation for GPIO controlled pullups · a74022a5
      由 Lars-Peter Clausen 提交于 
      Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      a74022a5
    • A
      arm: omap4: 4430sdp: drop ehci support · 09173b58
      由 Anand Gadiyar 提交于 
      Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      09173b58
    • S
      USB: OHCI: use pci_dev->revision · fa417c36
      由 Sergei Shtylyov 提交于 
      Commit ab1666c1 (USB: quirk PLL power down mode)
added code that reads the revision ID from the PCI configuration register while
it's stored by PCI subsystem in the 'revision' field of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      fa417c36
    • P
      USB: Rename "msm72k_otg.c" to "msm_otg.c" · dfb2130c
      由 Pavankumar Kondeti 提交于 
      This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      dfb2130c
    • A
      usb/isp1760: Fix crash when unplugging bug · d3cf2a8d
      由 Arvid Brodin 提交于 
      This fixes a problem with my previous patch series where there's a great
risk that the kernel will crash when unplugging interrupt devices from
the USB port. These lines must have got missing when I rebased the
patches from the older kernel I was working with to 2.6.37 and 2.6-next:

This fixes a bug where the kernel may crash if you unplug a USB device
that has active interrupt transfers.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      d3cf2a8d
    • A
      USB: move usbcore away from hcd->state · 9b37596a
      由 Alan Stern 提交于 
      The hcd->state variable is a disaster.  It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes.  It's
not protected by any locks.  And there's no mechanism to prevent it
from going through an invalid transition.

This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died.  Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information.  The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).

The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them.  Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT.  Nevertheless, the new code is a
big improvement over the current code.

The patch makes one other change.  The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.

This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAlex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      9b37596a
  9. 03 3月, 2011 5 次提交
  11. 02 3月, 2011 2 次提交
    • Y
      usb: EHCI, OHCI: Add configuration for the SH USB controller · 60b0bf0f
      由 Yoshihiro Shimoda 提交于 
      The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      60b0bf0f
    • A
      USB host: Move AMD PLL quirk to pci-quirks.c · ad93562b
      由 Andiry Xu 提交于 
      This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.

AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:

1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
   in low power state is enabled.

Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.

Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:

1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
   make them cleaner;
2. AMD chipset information will be probed only once and then stored.
   Currently they're probed during every OHCI/EHCI initialization, move
   the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
   code, every host controller enable/disable PLL only according to
   its own status, and may enable PLL while there is still isoc transfer on
   other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      ad93562b
  13. 01 3月, 2011 8 次提交