This makes hotplug, NCQ, etc. possible, and removes one of the few
remaining old-EH drivers.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
  not exist
* Set I/O Id field in descriptor, where present.  Appears to work
  fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
  and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
  are always masked)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Minor cleanups, new definitions, and code movement, preparing for
upcoming new-EH and NCQ changes.  This commit shoult not change behavior
at all.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate out ata_eh_handle_dev_fail() from ata_eh_recover().  This is
in preparation of ata_link and PMP support.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hook that set DMA mode was accidentally deleted in the original patch.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add Hitachi HDS7250SASUN500G 0621KTAWSD to list of devices with broken NCQ.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NAkira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Please warmly welcome the first member from FUJITSU to the prestigious
NCQ spurious completion club.

This is reported by Serge Van Thillo in bugzilla bug 8730.

  http://bugzilla.kernel.org/show_bug.cgi?id=8730Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Serge van Thillo <nulleke@hotmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The HPT343/345 (aka 363) is a bit of a warped device.  For many setups you
need to access the other registers via BAR4 offsets.  PIO is now rock
solid, DMA isn't.  Unfortunately the drivers/ide hpt34x driver is
completely broken so doesn't help further debug.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Horkage handling had the following problems.

* dev->horkage was positioned after ATA_DEVICE_CLEAR_OFFSET, so it was
  cleared before the device is configured.  This broke
  HORKAGE_DIAGNOSTIC.

* Some used dev->horkage while others called ata_device_blacklisted()
  directly.  This was at best confusing.

This patch moves dev->horkage right after dev->flags and set the field
according to the blacklist during device configuration.  All users
test against dev->horkage.  ata_device_blacklisted() now has only one
user, make it static.  While at it, rename it to ata_dev_blacklisted()
for consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Zip 250 which chokes on MWDMA SET_XFERMODE sometimes have "Floppy"
appeneded to its model number.  Quirk it too.

  http://bugzilla.kernel.org/show_bug.cgi?id=8563Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Hans de Bruin <bruinjm@xs4all.nl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With PCI resource fix up for legacy hosts.  We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts.  Only IRQ requesting needs to be different.

Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead.  This
simplifies code a lot.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement suspend and resume routines for mpc52xx ata driver.
Tested on Lite5200b with deep-sleep and low-power (not yet in-tree)
modes.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch enables hotplugging of SATA devices in the
sata_promise driver. It's been tested successfully on
both first- and second-generation Promise SATA chips:
SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4,
SATA300 TX2plus, and SATA300 TX4.

The only quirk I've seen is that hotplugging (insertion)
on the first-generation SATA150 TX2plus requires a lengthier
EH sequence than on the second-generation chips.
On the second-generation chips a simple soft reset seems
to suffice, but on the first-generation chip there's a
"port is slow to respond" after the initial soft reset,
after which libata issues a hard reset, and then the
device is recognised.

The hotplug checks are high up in the interrupt handling
path, not deep down in error_intr as in ahci/sata_sil24.
That's because the chip doesn't signal hotplug status changes
in the per-port status register: instead a global register
contains hotplug control and status flags for all ports.
I considered following the ahci/sata_sil24 structure, but
that would have required non-trivial changes to the interrupt
handling path, so I chose to keep the hotplug changes simple
and unobtrusive.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
--
This patch depends on the "sata_promise: cleanups" patch.

Changes since the previous version (posted June 19):
- Correct pdc_interrupt() to increment 'handled' also in
  the hotplug case. This prevents IRQ_NONE from being
  returned when an interrupt only has hotplug events to
  handle, which could confuse the kernel's IRQ machinery.
- Added testing on the SATAII150 TX4.

 drivers/ata/sata_promise.c |   41 ++++++++++++++++++++++++++++++++++++-----
 1 files changed, 36 insertions(+), 5 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If you are using a SiS controller and the BIOS didn't set it up then the
FIFO may be left active when we try and set up the CD. Not convinced this
matters but I'd prefer to be safe
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We should not use cancel_work_sync(delayed_work->work). This works, but not
good. We can use cancel_rearming_delayed_work(), this also simplifies the
code.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Hi,

This is the third submission of the network driver for PS3.
The differences from the previous one are:

  - renamed source file names so that their prefix can match
    with the module name
  - added cbe-oss-dev@ozlabs.org line for MAINTAINER file
  - changed some in copyright comments

If there are no more comments, please apply for 2.6.23.

Thank you

--
Subject: PS3: Ethernet driver

From: Masakazu Mokuno <mokuno@sm.sony.co.jp>

Add Gigabit Ethernet support for the PS3 game console.  The module will
be called ps3_gelic.

CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It needs writesb(), not available on all platforms.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.

Missing goto has been included.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unmaintained, superceded by skge.

Prodded to deletion by Adrian Bunk.  Acked by Stephen Hemminger.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the following section mismatch:

<--  snip  -->

...
  MODPOST vmlinux
WARNING: drivers/built-in.o(.text+0x272f8b): Section mismatch: reference to .init.text:quattro_pci_find (between 'happy_meal_pci_probe' and 'happy_meal_pci_remove')
...

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing).  This causes DAD and RS
packets to be sent from the slave.  These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).

	This patch alters the behavior so that addrconf will only run on
the master device itself.  I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master.  This is consistent with the IPv4 behavior for bonding.

	This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.

	The eql driver also uses the IFF_SLAVE flag.  I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Code will do local_irq_save() on it.
Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Based on an original idea by John W. Linville.

It is the missing part of 42d45ccd60636c28e35c2016f091783bc14ad99c
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.

The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

  LD      vmlinux
  SYSMAP  System.map
  SYSMAP  .tmp_System.map
  MODPOST vmlinux
WARNING: drivers/built-in.o(.data+0x2480): Section mismatch: reference to .init.text: (between 'sercons' and 'ds_parms')
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM.  So we must provide its ethernet address by another way.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NFranck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/configs/ocelot_c_defconfig
 delete mode 100644 arch/mips/momentum/ocelot_c/Makefile
 delete mode 100644 arch/mips/momentum/ocelot_c/cpci-irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/dbg_io.c
 delete mode 100644 arch/mips/momentum/ocelot_c/irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/ocelot_c_fpga.h
 delete mode 100644 arch/mips/momentum/ocelot_c/platform.c
 delete mode 100644 arch/mips/momentum/ocelot_c/prom.c
 delete mode 100644 arch/mips/momentum/ocelot_c/reset.c
 delete mode 100644 arch/mips/momentum/ocelot_c/setup.c
 delete mode 100644 arch/mips/momentum/ocelot_c/uart-irq.c
 delete mode 100644 arch/mips/pci/fixup-ocelot-c.c
 delete mode 100644 arch/mips/pci/pci-ocelot-c.c

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Convert the IOC3 driver to use ref counting pci interfaces so that we can
obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid
future authors writing hotplug-unsafe device drivers.
Signed-off-by: NAlan Cox <alan@redhat.com>

Build fixes:
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The 82550 & 51 parts have an extended configuration block that
includes a bit "GMRC", required to enable the expected TCO behavior,
in config byte offset 22d.  The config block sent by the failing driver
does include the extension area, but this bit is not initialised,
and the downlaod only specifies 0x16 bytes to be sent to the NIC
(thaht's bytes 00..21d). By initializing the GMRC bit, and extending
the download size for D102+ MACs, the problem is resolved.
Signed-off-by: NDavid Graham <david.graham@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>