- 29 4月, 2011 8 次提交
-
-
由 Sujith Manoharan 提交于
This patch adds a new API for setting a TX rate mask in drivers that have rate control in either the firmware or hardware. This can be used for various purposes, for example, masking out the 11b rates in P2P operation. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Randy Dunlap 提交于
Convert all libertas/ files to use kernel-doc notation instead of whatever it was (doxygen?). Add or fix function parameters in several places. Use expected style for multi-line comments in lots of places. Remove erroneous /** in multiple places. Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arik Nemtsov 提交于
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events. Both are reported to the upper layers as a TX failure in the offending stations. In STA mode we register only for the MAX_TX_RETRY event. A TX failure is interpreted as a loss of connection. Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid the inherent race condition of a mac80211 TX failure counter in addition to the FW counter. This patch depends on "mac80211: allow low level driver to report packet loss" Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Use ps wrappers before accessing hw registers in btcoex. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Generic timer interrupt was not triggered unless autosleep was disabled. Since autosleep is enabled in the newer chipsets, enable generic timer for using with bt coex logic. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Move bt_stomp to ath9k_hw and add its support for latest chipsets. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arik Nemtsov 提交于
Add API that allows low level drivers to notify mac80211 about TX packet loss. This is useful when there are FW triggers to notify the low level driver about these events. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 27 4月, 2011 29 次提交
-
-
由 Luis R. Rodriguez 提交于
The patch "cfg80211: add a timer for invalid user reg hints" introduced a regression for the case where a secondary identical regulatory hint from a user is sent. What would happen is the second hint would schedule delayed work in to catch a timeout but since we are never processing it given that the hint was already applied we'd always hit the timeout and and restore regulatory settings back to world regulatory domain. This is fixed by simply avoiding sheduling work if the hint was already applied. Tested-by: NFelix Fietkau <nbd@openwrt.org> Reported-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Fix most sparse warnings in rtlwifi, rtl8192ce and rtl8192cu drivers. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
rtlwifi: rtl8192ce: Change rtl8192ce routines phy and trx and modify rtl8192cu for addition of rtl8192se and rtl8192de Change rtl8192ce routines phy and trx for addition of RTL8192SE and RTL8192DE. In addition, make necessary modifications to rtl8192cu. This patch also removes the temporary patches needed to enable intermediate steps to build without error. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change rtl8192ce routines phy and rc for addition of RTL8192SE and RTL8192DE. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change rtl8192ce sw and LED routines for addition of RTL8192SE and RTL8192DE. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change rtl8192ce hw routine for addition of RTL8192SE and RTL8192DE. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change common PHY routines for addition of RTL8192SE and RTL8192DE code. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change common firmware routines for addition of RTL8192SE and RTL8192DE code. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de Convert common dynamic management routines for addition of RTL8192SE and RTL8192DE code. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert usb routines for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert regulatory domain routines for addition of RTL8192SE and RTL8192DE code. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert rc routines for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert ps routines for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert pci routines for addition of RTL8192SE and RTL8192DE code These changes allow the upper-level driver to specify the BAR to be used as it is different for rtl8192se than for the others. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Convert core routines for addition of RTL8192SE and RTL8192DE code. Additional files are changed to allow compilation. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change cam routines for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change base routines for addition of RTL8192SE and RTL8192DE code. Additional files are modified to allow compilation. Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change wifi.h for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chaoming_Li 提交于
Change efuse routines for addition of RTL8192SE and RTL8192DE code Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
These warnings are exposed by gcc 4.6. net/mac80211/sta_info.c: In function 'sta_info_cleanup_expire_buffered': net/mac80211/sta_info.c:590:32: warning: variable 'sdata' set but not used net/mac80211/ibss.c: In function 'ieee80211_rx_mgmt_auth_ibss': net/mac80211/ibss.c:43:34: warning: variable 'status_code' set but not used net/mac80211/work.c: In function 'ieee80211_send_assoc': net/mac80211/work.c:203:9: warning: variable 'len' set but not used net/mac80211/tx.c: In function '__ieee80211_parse_tx_radiotap': net/mac80211/tx.c:1039:35: warning: variable 'sband' set but not used net/mac80211/mesh.c: In function 'ieee80211_mesh_rx_queued_mgmt': net/mac80211/mesh.c:616:28: warning: variable 'ifmsh' set but not used ... Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
The release timer has to expire "just" after a frame is up for release. Currently, if the timer callback starts on time, the "!time_after" check above will start a new timer instead of releasing the frames. Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Using the ieee80211_sta_block allows the PS code to handle awake->doze->awake transitions of our clients in a race-free manner. Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
"For best CPU usage and power consumption, having as few frames as possible percolate through the stack is desirable. Hence, the hardware should filter as much as possible." Note: Not all firmwares include the multicast filter feature and the stack does not filter them either. The ARP filter on the other hand was dropped from the patch since it does not work correctly: Quote from: Max Filippov <jcmvbkbc@gmail.com> <http://www.spinics.net/lists/linux-wireless/msg67466.html> "In the ARP case, when there's no other traffic on p54spi, all ARP requests are dropped. But if there's some egress traffic from p54spi, filter seems to work correctly: only ARP requests that match filter pass through. In the multicast case filter seems to work correctly, but it treats broadcast as subject to that filtering too. By default only 01:00:5e:00:00:01 gets into priv->mc_maclist, so we miss all broadcasts. These two filters seem to interfere: - if we set ARP filter and multicast filter without bc => we miss all ARPs if there's no egress traffic; - if we set ARP filter and multicast filter with bc or don't set mc filter at all => we get all ARPs. This effect does not depend on filter setup order." Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Tested-by: NMax Filippov <jcmvbkbc@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
My 14e4:4315 is SSB_IDLOW_SSBREV_26: read32 0xfaafcff8 -> 0x600422d5 My 14e4:4328 is SSB_IDLOW_SSBREV_24: read32 0xfaafcff8 -> 0x400422c5 My 14e4:432b is SSB_IDLOW_SSBREV_26 again: read32 0xfaafcff8 -> 0x600422d5 For all of them wl driver is using 0x2 reject bit: write32(0xf98) <- 0x00010002 So it seems SSB 2.3 is the exception using another bit. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
ssb_chipco_set_clockmode may want to touch CC registers to control power of the bus. However touching registers without powered_up set causes warnings. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Adrian Chadd 提交于
The xpaBiasLvlFreq parameter array is made up of 16 bit words which aren't byte-swapped like the other 16-bit eeprom parameters are. It's only used by the AR9160. Signed-off-by: NAdrian Chadd <adrian@freebsd.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Requesting beacon sync up to configure beacon timers properly in hw, has be done after doing beacon config with default values. Setting the flags in beacon config is causing the device to not enter into network sleep on idle state. Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
On AR9003 chips, doing three IQ calibrations will possibly cause chip in stuck state. In noisy environment, chip could receive a packet during the middle of three calibrations and it causes the conflict of HW access and the eventual failure. It also causes IQ calibration outliers which results in poor Tx EVM. The IQ Cal procedure is after resetting the chip, run IQ cal 3 times per each cal cycle and find the two closest readings and average of two. The advantage of running Tx IQ cal more than once is that we can compare calibration results for the same gain setting over multiple iterations. Most of the cases the IQ failures were observed after first pass. For the AR9485 and later chips, Tx IQ Calibration is performed along with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated from the rest of calibration HW to avoid chip hang. After all calibrations are done in HW, we can start SW post-processing. By doing this way, we minimize the SW difference among all chips. The order of calibration (run IQ cal before other calibration) is also needed to avoid chip hang for chips before AR9485. This issue was originally observed with AR9382. During the issue kernel log was filled with following message ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000 ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000 ath: Unable to reset channel (2412 MHz), reset status -5 ath: Unable to set channel Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 4月, 2011 3 次提交
-
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
This helped the developers to fix an issue of chip not entering network sleep during idle state, previously this was only available as a debug message Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
newer chipsets support auto sleep feature, so remove the unlikely check which does not seems to help anything Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-