These processors do not currently support doorbell IPIs, so remove them
from the feature list if we are at DD 1.xx for the 0x004d part.

This fixes a regression caused by d4e58e59 (powerpc/powernv: Enable
POWER8 doorbell IPIs). With that patch the kernel would hang at boot
when calling smp_call_function_many, as the doorbell would not be
received by the target CPUs:

  .smp_call_function_many+0x2bc/0x3c0 (unreliable)
  .on_each_cpu_mask+0x30/0x100
  .cpuidle_register_driver+0x158/0x1a0
  .cpuidle_register+0x2c/0x110
  .powernv_processor_idle_init+0x23c/0x2c0
  .do_one_initcall+0xd4/0x260
  .kernel_init_freeable+0x25c/0x33c
  .kernel_init+0x1c/0x120
  .ret_from_kernel_thread+0x58/0x7c

Fixes: d4e58e59 (powerpc/powernv: Enable POWER8 doorbell IPIs)
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We are seeing a lot of PMU warnings on POWER8:

    Can't find PMC that caused IRQ

Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.

A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.

This patch takes the second option.

Cc: <stable@vger.kernel.org>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc:allmodconfig has been failing for some time with the following
error.

arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1312: Error: attempt to move .org backwards
make[1]: *** [arch/powerpc/kernel/head_64.o] Error 1

A number of attempts to fix the problem by moving around code have been
unsuccessful and resulted in failed builds for some configurations and
the discovery of toolchain bugs.

Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead.
While this is less than perfect, it avoids substantial code changes
which would otherwise be necessary just to make COMPILE_TEST builds
happy and might have undesired side effects.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.

We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.

This was manifesting as a bug with ppc64_cpu --frequency:

    $ sudo ppc64_cpu --frequency
    WARNING: couldn't run on cpu 0
    WARNING: couldn't run on cpu 8
      ...
    WARNING: couldn't run on cpu 144
    WARNING: couldn't run on cpu 152
    min:    18446744073.710 GHz (cpu -1)
    max:    0.000 GHz (cpu -1)
    avg:    0.000 GHz

The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.

By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:

    $ sudo sh -c 'echo p > /proc/sysrq-trigger'
    CPU: 0 PMU registers, ppmu = POWER8 n_counters = 6
    PMC1:  5b635e38 PMC2: 00000000 PMC3: 00000000 PMC4: 00000000
    PMC5:  1bf5a646 PMC6: 5793d378 PMC7: deadbeef PMC8: deadbeef
    MMCR0: 0000000080000000 MMCR1: 000000001e000000 MMCRA: 0000040000000000
    MMCR2: fffffffffffffc00 EBBHR: 0000000000000000
    EBBRR: 0000000000000000 BESCR: 0000000000000000
    SIAR:  00000000000a51cc SDAR:  c00000000fc40000 SIER:  0000000001000000

This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.

Fixes: e05b9b9e ("powerpc/perf: Power8 PMU support")
Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.

This saves us adding a MMCR2 define for a future patch.

Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These two registers are already saved in the block above. Aside from
being unnecessary, by the time we get down to the second save location
r8 no longer contains MMCR2, so we are clobbering the saved value with
PMC5.

MMCR2 primarily consists of counter freeze bits. So restoring the value
of PMC5 into MMCR2 will most likely have the effect of freezing
counters.

Fixes: 72cde5a8 ("KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8")
Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NPaul Mackerras <paulus@samba.org>
Reviewed-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 8d6f7c5a: "powerpc/powernv: Make it possible to skip the IRQHAPPENED
check in power7_nap()" added code that prevents cpus from checking for
pending interrupts just before entering sleep state, which is wrong. These
interrupts are delivered during the soft irq disabled state of the cpu.

A cpu cannot enter any idle state with pending interrupts because they will
never be serviced until the next time the cpu is woken up by some other
interrupt. Its only then that the pending interrupts are replayed. This can result
in device timeouts or warnings about this cpu being stuck.

This patch fixes ths issue by ensuring that cpus check for pending interrupts
just before entering any idle state as long as they are not in the path of split
core operations.
Signed-off-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In fb5a5157 "powerpc: Remove platforms/wsp and associated pieces",
we removed the last user of MMU_FTRS_A2. So remove it.

MMU_FTRS_A2 was the last user of MMU_FTR_TYPE_3E, so remove it also.
This leaves some unreachable code in mmu_context_nohash.c, so remove
that also.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 046d662f "coredump: make core dump functionality optional"
made the coredump optional, but didn't update the spufs code that
depends on it. That leads to build errors such as:

  arch/powerpc/platforms/built-in.o: In function `.spufs_arch_write_note':
  coredump.c:(.text+0x22cd4): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22cf4): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22d0c): undefined reference to `.dump_align'
  coredump.c:(.text+0x22d48): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22e7c): undefined reference to `.dump_skip'

Fix it by adding some ifdefs in the cell code.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 59a53afe "powerpc: Don't setup
CPUs with bad status" broke ePAPR SMP booting.  ePAPR says that CPUs
that aren't presently running shall have status of disabled, with
enable-method being used to determine whether the CPU can be enabled.

Fix by checking for spin-table, which is currently the only supported
enable-method.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The commit 71ec7c55 introduced the magic symbol ".TOC." for ELFv2 ABI.
This symbol is built manually and has no CRC value computed. A zero value
is put in the CRC section to avoid modpost complaining about a missing CRC.
Unfortunately, this breaks the kernel module loading when the kernel is
relocated (kdump case for instance) because of the relocation applied to
the kcrctab values.

This patch compute a CRC value for the TOC symbol which will match the one
compute by the kernel when it is relocated - aka '0 - relocate_start' done in
maybe_relocated called by check_version (module.c).
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 27f44888 "Add OPAL takeover from PowerVM" we added support
for "takeover" on OPAL v1 machines.

This was a mode of operation where we would boot under pHyp, and query
for the presence of OPAL. If detected we would then do a special
sequence to take over the machine, and the kernel would end up running
in hypervisor mode.

OPAL v1 was never a supported product, and was never shipped outside
IBM. As far as we know no one is still using it.

Newer versions of OPAL do not use the takeover mechanism. Although the
query for OPAL should be harmless on machines with newer OPAL, we have
seen a machine where it causes a crash in Open Firmware.

The code in early_init_devtree() to copy boot_command_line into cmd_line
was added in commit 817c21ad "Get kernel command line accross OPAL
takeover", and AFAIK is only used by takeover, so should also be
removed.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The DART table allocation is registered to kmemleak via the
memblock_alloc_base() call. However, the DART table is later unmapped
and dart_tablebase VA no longer accessible. This patch tells kmemleak
not to scan this block and avoid an unhandled paging request.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This gives us standardised success/failure output and also handles
killing the test if it runs forever (2 minutes).
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This variable is of the wrong type, everywhere it is used it
should be an unsigned int rather than a int.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 721aeaa9 "Build little endian ppc64 kernel with ABIv2", we
missed some updates required in the kprobes code to make jprobes work
when the kernel is built with ABI v2.

Firstly update arch_deref_entry_point() to do the right thing. Now that
we have added ppc_global_function_entry() we can just always use that, it
will do the right thing for 32 & 64 bit and ABI v1 & v2.

Secondly we need to update the code that sets up the register state before
calling the jprobe handler. On ABI v1 we setup r2 to hold the TOC, on ABI
v2 we need to populate r12 with the function entry point address.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The printks() in our ftrace code have no prefix, so they appear on the
console with very little context, eg:

  Branch out of range

Use pr_fmt() & pr_err() to add a prefix. While we're at it, collapse a
few split lines that don't need to be, and add a missing newline to one
message.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There is a bug in the handling of the function entry when we are nopping
out a branch from a module in ftrace.

We compare the result of module_trampoline_target() with the value of
ppc_function_entry(), and expect them to be true. But they never will
be.

module_trampoline_target() will always return the global entry point of
the function, whereas ppc_function_entry() will always return the local.

Fix it by using the newly added ppc_global_function_entry().
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 24a1bdc3, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that creates and patches the branch, and added a
thinko in the check of create_branch(). create_branch() returns the
instruction that was generated, so if we get zero then it succeeded.

The result is we can't ftrace modules:

  Branch out of range
  WARNING: at ../kernel/trace/ftrace.c:1638
  ftrace failed to modify [<d000000004ba001c>] fuse_req_init_context+0x1c/0x90 [fuse]

We should probably fix patch_instruction() to do that check and make the
API saner, but that's a separate patch. For now just invert the test.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 24a1bdc3, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that checks for the expected code sequence when
patching a module.

We missed the typo in the mask, 0xffff00000 should be 0xffff0000, which
has the effect of making the test always true.

That makes it impossible to ftrace against modules, eg:

  Unexpected call sequence: 48000008 e8410018
  WARNING: at ../kernel/trace/ftrace.c:1638
  ftrace failed to modify [<d000000007cf001c>] rng_dev_open+0x1c/0x70 [rng_core]
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

ABIv2 has the concept of a global and local entry point to a function.
In most cases we are interested in the local entry point, and so that is
what ppc_function_entry() returns.

However we have a case in the ftrace code where we want the global entry
point, and there may be other places we need it too. Rather than special
casing each, add an accessor.

For ABIv1 and 32-bit there is only a single entry point, so we return
that. That means it's safe for the caller to use this without also
checking the ABI version.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

A closing brace followed by "if" is almost certainly a mistake. Maybe
"else if" was meant, but in this case it doesn't really matter.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The generic code uses gcc built-ins which work fine so there's no benefit
in implementing our own anymore.

We can't completely remove the ld/st_le* functions as some historical
cruft still uses them, but that's next on the radar
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have some compile-time disabled debug code in signal_xx.c. It's from
some ancient time BG, almost certainly part of the original port, given
the very similar code on other arches.

The show_unhandled_signal logic, added in d0c3d534 (2.6.24) is
cleaner and prints more useful information, so drop the debug code.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In arch/powerpc/kernel/iomap.c, lots of IO reading accessors missed
to check EEH error as Ben pointed. The patch fixes it.

For the writing accessors, we change the called functions only for
making them look similar to the reading counterparts.
Suggested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This reverts commit e1edf18b.

This patch was a misguided attempt at fixing offb for LE ppc64
kernels on BE qemu but is just wrong ... it breaks real LE/LE
setups, LE with real HW, and existing mixed endian systems
that did the fight thing with the appropriate device-tree
property. Bad reviewing on my part, sorry.

The right fix is to either make qemu change its endian when
the guest changes endian (working on that) or to use the
existing foreign endian support.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13+]
---

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: NJoseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull more SCSI updates from James Bottomley:
 "This is just a couple of drivers (hpsa and lpfc) that got left out for
  further testing in linux-next.  We also have one fix to a prior
  submission (qla2xxx sparse)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
  qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
  lpfc: Update lpfc version to driver version 10.2.8001.0
  lpfc: Fix ExpressLane priority setup
  lpfc: mark old devices as obsolete
  lpfc: Fix for initializing RRQ bitmap
  lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
  lpfc: Update lpfc version to driver version 10.2.8000.0
  lpfc: Update Copyright on changed files from 8.3.45 patches
  lpfc: Update Copyright on changed files
  lpfc: Fixed locking for scsi task management commands
  lpfc: Convert runtime references to old xlane cfg param to fof cfg param
  lpfc: Fix FW dump using sysfs
  lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
  lpfc: Fixed kernel panic in lpfc_abort_handler
  lpfc: Fix locking for postbufq when freeing
  lpfc: Fix locking for lpfc_hba_down_post
  lpfc: Fix dynamic transitions of FirstBurst from on to off
  hpsa: fix handling of hpsa_volume_offline return value
  hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
  hpsa: remove messages about volume status VPD inquiry page not supported
  ...

Pull more btrfs updates from Chris Mason:
 "This has a few fixes since our last pull and a new ioctl for doing
  btree searches from userland.  It's very similar to the existing
  ioctl, but lets us return larger items back down to the app"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  btrfs: tree_search, search_ioctl: direct copy to userspace
  btrfs: new function read_extent_buffer_to_user
  btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
  btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
  btrfs: tree_search, search_ioctl: accept varying buffer
  btrfs: tree_search: eliminate redundant nr_items check

Pull aio fix and cleanups from Ben LaHaise:
 "This consists of a couple of code cleanups plus a minor bug fix"

* git://git.kvack.org/~bcrl/aio-next:
  aio: cleanup: flatten kill_ioctx()
  aio: report error from io_destroy() when threads race in io_destroy()
  fs/aio.c: Remove ctx parameter in kiocb_cancel