Split dev_change_flags() into two functions: __dev_change_flags() to
perform the actual changes and __dev_notify_flags() to invoke netdevice
notifiers. This will be used by rtnl_link to defer netlink notifications
until the device has been fully configured.

This changes ordering of some operations, in particular:

- netlink notifications are sent after all changes have been performed.
  As a side effect this surpresses one unnecessary netlink message when
  the IFF_UP and other flags are changed simultaneously.

- The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked
  after all changes have been performed. Their relative is unchanged.

- net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead
  of afterwards. This should not make any difference since both RX and TX
  are already shut down at this point.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support specifying device flags during device creation,
we must be able to roll back device registration in case setting the
flags fails without sending any notifications related to the device
to userspace.

This patch changes rollback_registered_many() and register_netdevice()
to manually send netlink notifications for devices not handled by
rtnl_link and allows to defer notifications for devices handled by
rtnl_link until setup is complete.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In "wireless: remove WLAN_80211 and WLAN_PRE80211 from Kconfig" I
inadvertantly missed a line in include/linux/netdevice.h.  I thereby
effectively reverted "net: Set LL_MAX_HEADER properly for wireless." by
accident. :-(  Now we should check there for CONFIG_WLAN instead.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reported-by: NChristoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: stable@kernel.org

Add netdev ops for configuring SR-IOV VF devices through the PF driver.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add macros to test a private structure for msg_enable bits
and the netif_msg_##bit to test and call netdev_printk if set

Simplifies logic in callers and adds message logging consistency
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These netdev_printk routines take a struct net_device * and emit
dev_printk logging messages adding "%s: " ... netdev->dev.parent
to the dev_printk format and arguments.

This can create some uniformity in the output message log.

These helpers should not be used until a successful alloc_netdev.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patchset enables the ethtool layer to program n-tuple
filters to an underlying device.  The idea is to allow capable
hardware to have static rules applied that can assist steering
flows into appropriate queues.

Hardware that is known to support these types of filters today
are ixgbe and niu.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the similar helpers as those already done for uc list.
However multicast lists are no list_head lists but "mademanually". The three
macros added by this patch will make the transition of mc_list to list_head
smooth in two steps:

1) convert all drivers to use these macros (with the original iterator of type
   "struct dev_mc_list")
2) once all drivers are converted, convert list type and iterators to "struct
   netdev_hw_addr" in one patch.

>From now on, drivers can (and should) use "netdev_for_each_mc_addr" to iterate
over the addresses with iterator of type "struct netdev_hw_addr". Also macros
"netdev_mc_count" and "netdev_mc_empty" to read list's length. This is the state
which should be reached in all drivers.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.

To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After netdev_ops compat code HAVE_* macros aren't needed, in fact
they _will_ result in compile breakage for out of tree drivers.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing outside of net/core/dev.c uses it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: NPatrick Mullaney <pmullaney@novell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I will need this shortly to implement network namespace shutdown
batching.  For sanity sake network devices should be removed in
the reverse order they were created in.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.

Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Herbert Xu a écrit :
> On Tue, Nov 17, 2009 at 04:26:04AM -0800, David Miller wrote:
>> Really, the link watch stuff is just due for a redesign.  I don't
>> think a simple hack is going to cut it this time, sorry Eric :-)
>
> I have no objections against any redesigns, but since the only
> caller of linkwatch_forget_dev runs in process context with the
> RTNL, it could also legally emit those events.

Thanks guys, here an updated version then, before linkwatch surgery ?

In this version, I force the event to be sent synchronously.

[PATCH net-next-2.6] linkwatch: linkwatch_forget_dev() to speedup device dismantle

time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105

real	0m0.266s
user	0m0.000s
sys	0m0.001s

real	0m0.770s
user	0m0.000s
sys	0m0.000s

real	0m1.022s
user	0m0.000s
sys	0m0.000s

One problem of current schem in vlan dismantle phase is the
holding of device done by following chain :

vlan_dev_stop() ->
	netif_carrier_off(dev) ->
		linkwatch_fire_event(dev) ->
			dev_hold() ...

And __linkwatch_run_queue() runs up to one second later...

A generic fix to this problem is to add a linkwatch_forget_dev() method
to unlink the device from the list of watched devices.

dev->link_watch_next becomes dev->link_watch_list (and use a bit more memory),
to be able to unlink device in O(1).

After patch :
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105

real    0m0.024s
user    0m0.000s
sys     0m0.000s

real    0m0.032s
user    0m0.000s
sys     0m0.001s

real    0m0.033s
user    0m0.000s
sys     0m0.000s
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers ndo_get_stats() method need to perform txqueue stats folding.

Move folding from dev_get_stats() to a new dev_txq_stats_fold() function
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.

After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.

Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No longer need read_lock(&dev_base_lock), use RCU instead.
We also can avoid taking references on inet6_dev structs.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.

This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.

In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds an RCU macro for continuing search, useful for some
network devices like vlan.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleanup patch puts struct/union/enum opening braces,
in first line to ease grep games.

struct something
{

becomes :

struct something {
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds RCU management to the list of netdevices.

Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock

Ie:
	read_lock(&dev_base_loack);
	for_each_netdev(net, dev)
		some_action();
	read_unlock(&dev_base_lock);

becomes :

	rcu_read_lock();
	for_each_netdev_rcu(net, dev)
		some_action();
	rcu_read_unlock();
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock
(and avoid touching netdevice refcount)

netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.

However, it adds a synchronize_rcu() call in dev_change_name()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This isn't beautifully abstracted, but it is simple,
simplifies uses and so far is only needed for the bonding driver.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow drivers to adjust their receive path dynamically
based on whether GRO is being applied successfully.

Currently all in-tree callers ignore the return values of these
functions and do not need to be changed.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This clarifies which return and parameter types are GRO result codes
and not RX result codes.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock.

netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.

dev_ifname() converted to dev_get_by_index_rcu()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_fcoe_get_wwn so Fiber Channel over Ethernet (FCoE) can make use of
the provided World Wide Port Name (WWPN) and World Wide Node Name (WWNN)
from the underlying network interface driver.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce rollback_registered_many() and unregister_netdevice_many()

rollback_registered_many() is able to perform necessary steps at device dismantle
time, factorizing two expensive synchronize_net() calls.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patchs adds an unreg_list anchor to struct net_device, and
introduces an unregister_netdevice_queue() function, able to queue
a net_device to a list instead of immediately unregister it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nanodoc was missing an ndo_-prefix.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data center bridging ops structure can be const
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let attribute group vectors be declared "const".  We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes commit e36b9d16. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:

*. It assumes tha the device is UP when calling dev_close(), or otherwise
   dev_close() has no affect. It is worth to mention that initscripts (Redhat)
   and sysconfig (Suse) doesn't act the same in this matter. 
*. dev_close() has other side affects, like deleting entries from the routing
   table, which might be unnecessary.

The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.

To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.

  # cat /sys/class/net/wlan0/uevent
  DEVTYPE=wlan
  INTERFACE=wlan0
  IFINDEX=5

This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.

The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the multiqueue integration with the qdisc API suffers from
a few problems:

- with multiple queues, all root qdiscs use the same handle. This means
  they can't be exposed to userspace in a backwards compatible fashion.

- all API operations always refer to queue number 0. Newly created
  qdiscs are automatically shared between all queues, its not possible
  to address individual queues or restore multiqueue behaviour once a
  shared qdisc has been attached.

- Dumps only contain the root qdisc of queue 0, in case of non-shared
  qdiscs this means the statistics are incomplete.

This patch reintroduces dev->qdisc, which points to the (single) root qdisc
from userspace's point of view. Currently it either points to the first
(non-shared) default qdisc, or a qdisc shared between all queues. The
following patches will introduce a classful dummy qdisc, which will be used
as root qdisc and contain the per-queue qdiscs as children.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_fcoe_enable/_disable to net_device_ops so the corresponding
HW can initialize itself for FCoE traffic or clean up after FCoE traffic is
done. This is expected to be called by the kernel FCoE stack upon receiving
a request for creating an FCoE instance on the corresponding netdev interface.
When implemented by the actual HW, the HW driver check the op code to perform
corresponding initialization or clean up for FCoE. The initialization normally
includes allocating extra queues for FCoE, setting corresponding HW registers
for FCoE, indicating FCoE offload features via netdev, etc. The clean-up would
include releasing the resources allocated for FCoE.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The transmit function should only return one of three possible values,
some drivers got confused and returned errno's or other values.
This changes the definition so that this can be caught at compile time.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>