提交 · bd132ec585c498ee27d7eedf8569703606743928 · openeuler / raspberrypi-kernel

08 11月, 2011 7 次提交

M
ASoC: Convert wm5100 to direct regmap API usage · bd132ec5
由 Mark Brown 提交于 10月 23, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
bd132ec5

ASoC: Convert WM8962 to direct regmap usage · 7b16f560

由 Mark Brown 提交于 11月 01, 2011

This initial conversion just moves the register init, regulator acquisition
and device verification out to the I2C probe(). Movement of other parts of
the driver like the GPIO and beep generation code will follow.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

7b16f560

ASoC: Convert WM8996 gpiolib to regmap · b2d1e233

由 Mark Brown 提交于 9月 19, 2011

Actually pretty straightforward.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

b2d1e233

ASoC: Move most WM8996 resource acquisition to I2C probe · ee5f3872

由 Mark Brown 提交于 9月 19, 2011

Now that the WM8996 driver is using the regmap API for register I/O we no
longer need the ASoC card to be active in order to interact with the chip.
In order to be more idiomatic for Linux move most of the existing probe()
function out into the I2C probe() function prior to registration with ASoC.

The IRQ and GPIO init will be moved separately as these are slightly more
involved.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ee5f3872

M
ASoC: Convert WM8996 to direct regmap API usage · 79172746
由 Mark Brown 提交于 9月 19, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
79172746

ASoC: Avoid a redundant read in cs42l51_pdn_event · e94de1e8

由 Axel Lin 提交于 11月 01, 2011

snd_soc_update_bits already does read-modify-write,
no need to read the register before calling snd_soc_update_bits.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

e94de1e8

ASoC: ak4642: ak4642 was tested · 20211391

由 Kuninori Morimoto 提交于 11月 06, 2011

ak4642 was tested by ms7724se board
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

20211391

05 11月, 2011 6 次提交

ASoC: Ensure we get an impedence reported for WM8958 jack detect · 19940b3d

由 Mark Brown 提交于 8月 19, 2011

Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

19940b3d

ASoC: Don't use wm8994->control_data when requesting IRQs · 5a3ad6bd

由 Mark Brown 提交于 11月 04, 2011

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

5a3ad6bd

ASoC: Don't use wm8994->control_data in wm8994_readable_register() · 8eeea521

由 Mark Brown 提交于 11月 04, 2011

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

8eeea521

ASoC: Disable thermal shutdown when not using speakers in wm_hubs · 03431972

由 Mark Brown 提交于 11月 04, 2011

The thermal shutdown support in wm_hubs devices is tied to the speaker
drivers (which are the only high power subsystems within the device).
Ensure minimal current usage when the thermal shutdown support is not
required by disabling the circuit when the speaker drivers are powered
down.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

03431972

ASoC: Manage thermal shutdown for WM8962 · 94b88e64

由 Mark Brown 提交于 11月 04, 2011

Disable the thermal shutdown circuits for headphone and speaker when the
relevant outputs are not enabled in order to save current in idle modes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

94b88e64

ASoC: Only enable thermal shutdown when required on WM9081 · a04e0c86

由 Mark Brown 提交于 11月 04, 2011

The WM9081 thermal shutdown is only effective when the speaker output is
enabled so disable it when that is not in use for a small current saving.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

a04e0c86

02 11月, 2011 9 次提交

M
ASoC: Fix sort of jz4740 in Makefile · 98dd932b
由 Mark Brown 提交于 11月 02, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
98dd932b

ASoC: Sort LM4857 with the CODECs in the Makefile · 8aafc435

由 Mark Brown 提交于 11月 02, 2011

Having a separate list for amps is a little confusing now the official
driver model for them is the same as for other CODECs so let's sort them
into the CODEC list, but only do this for those that are actual CODEC
drivers so it's easier to remember which ones need updating.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

8aafc435

ASoC: Disable MICBIAS and SYSCLK when stopping WM8962 accessory detection · 00ae3b86

由 Mark Brown 提交于 11月 01, 2011

They aren't needed any more. If machines need them for other purposes then
further changes will be required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

00ae3b86

ASoC: WM8962 accessory detection requires MICBIAS · a5ef9884

由 Mark Brown 提交于 11月 01, 2011

Force MICBIAS on as well as SYSCLK as the WM8962 accessory detection can't
function without both. No point in making machine drivers manually enable
it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

a5ef9884

ASoC: Enable SYSCLK last when enabling WM8962 mic detection · db0e5543

由 Mark Brown 提交于 11月 01, 2011

Ensure everything is set up before we start detecting.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

db0e5543

ASoC: Start WM8962 FLL if SYSCLK is enabled · 2a761cde

由 Mark Brown 提交于 11月 01, 2011

Since we have code to automatically manage the start and stop of the FLL
based on the SYSCLK widget if SYSCLK is already enabled and the FLL is
configured then we need to start it up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

2a761cde

M
ASoC: Ensure we always delay for WM8962 FLL when starting from SYSCLK · 0b7dd6ad
由 Mark Brown 提交于 11月 01, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
```
0b7dd6ad

ASoC: Ensure the WM8962 oscillator and PLLs start up disabled · 2af8de8c

由 Mark Brown 提交于 11月 01, 2011

Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

2af8de8c

ASoC: Ensure WM8962 PLL registers are reset · 4f4488ab

由 Mark Brown 提交于 11月 01, 2011

The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

4f4488ab

01 11月, 2011 14 次提交
- P
  sound: Add module.h to the previously silent sound users · da155d5b
  由 Paul Gortmaker 提交于 7月 15, 2011
```
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up.  So
fix up those users now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
```
  da155d5b
- M
  ASoC: Fix return value of wm5100_gpio_direction_out() · 64964e82
  由 Mark Brown 提交于 10月 31, 2011
```
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  64964e82
- M
  ASoC: Convert wm8400 MICBIAS to a supply widget · 3ff51c85
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  3ff51c85
- M
  ASoC: Convert wm8900 MICBIAS to a supply widget · 8a709d92
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  8a709d92
- M
  ASoC: Convert wm8904 MICBIAS to a supply widget · dcd658c5
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  dcd658c5
- M
  ASoC: Convert wm8960 MICBIAS to a supply widget · 187774cb
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  187774cb
- M
  ASoC: Convert wm8961 MICBIAS to a supply widget · 20abf088
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  20abf088
- M
  ASoC: Convert wm8974 MICBIAS to a supply widget · 48dd231b
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  48dd231b
- M
  ASoC: Convert wm8983 MICBIAS to a supply widget · 605b151a
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  605b151a
- M
  ASoC: Convert wm8985 MICBIAS to a supply widget · 812f8a35
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  812f8a35
- M
  ASoC: Convert wm8988 MICBIAS to a supply widget · be48f20d
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  be48f20d
- M
  ASoC: Convert wm8990 MICBIAS to a supply widget · e1fc3f21
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  e1fc3f21
- M
  ASoC: Convert wm8991 MICBIAS to a supply widget · b6406a80
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  b6406a80
- M
  ASoC: Convert wm8995 MICBIASes to supply widgets · 9ce31623
  由 Mark Brown 提交于 10月 27, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  9ce31623
31 10月, 2011 3 次提交

ASoC: WM8904: Set `invert' bit for Capture Switch · 5a7c5f26

由 Hong Xu 提交于 10月 28, 2011

Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

5a7c5f26

ASoC: Leave input audio data bit length settings untouched in wm8711_set_dai_fmt · d558cfc3

由 Axel Lin 提交于 10月 28, 2011

Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

d558cfc3

ASoC: wm8711: Fix wrong mask for setting input audio data bit length select · 04c57163

由 Axel Lin 提交于 10月 28, 2011

The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

04c57163

27 10月, 2011 1 次提交

ASoC: tlv320aic3x: Clear BIT_CLK_MASTER and WORD_CLK_MASTER bits for for slave mode · 68e47981

由 Axel Lin 提交于 10月 27, 2011

According to the datasheet:

Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
        0: Bit clock is an input (slave mode)
        1: Bit clock is an output (master mode)

BIT 6: Word Clock Directional Control
        0: Word clock is an input (slave mode)
        1: Word clock is an output (master mode)

Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

68e47981