- Add support for B4 board in board file b4_qds.c,
  It is common for B4860, B4420 and B4220QDS as they share same QDS board
- Add B4QDS support in Kconfig and Makefile

B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor,
with following major features:

    - Four dual-threaded e6500 Power Architecture processors
      organized in one cluster-each core runs up to 1.8 GHz
    - Two DDR3/3L controllers for high-speed memory interface each
      runs at up to 1866.67 MHz
    - CoreNet fabric that fully supports coherency using MESI protocol
      between the e6500 cores, SC3900 FVP cores, memories and
      external interfaces.
    - Data Path Acceleration Architecture having FMAN, QMan, BMan,
      SEC 5.3 and RMAN
    - Large internal cache memory with snooping and stashing capabilities
    - Sixteen 10-GHz SerDes lanes that serve:
        - Two SRIO interfaces. Each supports up to 4 lanes and
          a total of up to 8 lanes
        - Up to 8-lanes Common Public Radio Interface (CPRI) controller
          for glue-less antenna connection
        - Two 10-Gbit Ethernet controllers (10GEC)
        - Six 1G/2.5-Gbit Ethernet controllers for network communications
        - PCI Express controller
        - Debug (Aurora)
    - Various system peripherals

B4420 and B4220 have some differences in comparison to B4860 with fewer
core/clusters(both SC3900 and e6500), fewer DDR controllers,
fewer serdes lanes, fewer SGMII interfaces and reduced target frequencies.

Key differences between B4860 and B4420:
B4420 has:
    - Fewer e6500 cores:
        1 cluster with 2 e6500 cores
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.6GHz
    - 2 X 4 lane serdes
    - 3 SGMII interfaces
    - no sRIO
    - no 10G

Key differences between B4860 and B4220:
B4220 has:
    - Fewer e6500 cores:
        1 cluster with 1 e6500 core
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.33GHz
    - 2 X 2 lane serdes
    - 2 SGMII interfaces
    - no sRIO
    - no 10G
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Some minor changes to the common corenet_ds.c code are needed to support
the T4240QDS:
* Add support for "fsl,qoriq-pcie-v3.0" controller
* Bump max # of IRQs to 512 (T4240 supports more interrupts than
  previous SoCs).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We unified the Freescale pci/pcie initialization by changing the fsl_pci
to a platform driver. In previous PCI code architecture the initialization
routine is called at board_setup_arch stage. Now the initialization is done
in probe function which is architectural better. Also It's convenient for
adding PM support for PCI controller in later patch.

Now we registered pci controllers as platform devices. So we combine two
initialization code as one platform driver.
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Disintegrate asm/system.h for PowerPC.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org

The Freescale hypervisor does not allow guests to write to the timebase
registers (virtualizing the timebase register was deemed too complicated),
so don't try to synchronize the timebase registers when we're running
under the hypervisor.

This typically happens when kexec support is enabled.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.

On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: NVakul Garg <vakul@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P5020DS is in the same family of boards as the P4080 DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P3041DS is in the same family of boards as the P4080DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add basic support for the P4080 DS reference board.  None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>