At least on my HP 2540p this is wrong at bootup, fine
at any other time once a lid event has occured. This is due to
_REG vs _INI ordering in the ACPI tables.
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'intel/drm-intel-next' of ../drm-next: (755 commits)
  drm/i915: Only wait on a pending flip if we intend to write to the buffer
  drm/i915/dp: Sanity check eDP existence
  drm/i915: Rebind the buffer if its alignment constraints changes with tiling
  drm/i915: Disable GPU semaphores by default
  drm/i915: Do not overflow the MMADDR write FIFO
  Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
  drm/i915: Don't save/restore hardware status page address register
  drm/i915: don't store the reg value for HWS_PGA
  drm/i915: fix memory corruption with GM965 and >4GB RAM
  Linux 2.6.38-rc7
  Revert "TPM: Long default timeout fix"
  drm/i915: Re-enable GPU semaphores for SandyBridge mobile
  drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
  Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
  drm/i915: Allow relocation deltas outside of target bo
  drm/i915: Silence an innocuous compiler warning for an unused variable
  fs/block_dev.c: fix new kernel-doc warning
  ACPI: Fix build for CONFIG_NET unset
  mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
  x86: Use u32 instead of long to set reset vector back to 0
  ...

Conflicts:
	drivers/gpu/drm/i915/i915_gem.c

Apply the trivial conflicting regression fixes, but keep GPU semaphores
enabled.

Conflicts:
	drivers/gpu/drm/i915/i915_drv.h
	drivers/gpu/drm/i915/i915_gem_execbuffer.c

... as if we are only reading from it, we can do that concurrently with
the queue flip.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Some hardware claims to have both an LVDS panel and an eDP output.
Whilst this may be true in a rare case, more often it is just broken
hardware. If we see an eDP device we know that it must be connected and
so we can confirm its existence with a simple probe.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34165
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)

However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: NAndi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.

"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: NMatt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This reverts commit c2e0eb16.

As it turns out, userspace already depends upon being able to enable
tiling on existing bo which it promises to be large enough for its
purposes i.e. it will not access beyond the end of the last full-tile
row.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35016Reported-and-tested-by: NKamal Mostafa <kamal@canonical.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This allows libkms to make an easier decision.
Signed-off-by: NDave Airlie <airlied@redhat.com>

We're coming to see a need to have a set of generic capability checks in
the core DRM, in addition to the driver-specific ioctls that already
exist.

This patch defines an ioctl to do as such, but does not yet define any
capabilities.

[airlied: drop the driver callback for now.]
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

hdmi 1.3 raises the max clock from 165 Mhz to 340 Mhz.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* korg/drm-radeon-cayman:
  drm/radeon/kms: add cayman pci ids
  drm/radeon/kms: cayman/evergreen cs checker updates
  drm/radeon/kms/cayman: always set certain VGT regs at CP init
  drm/radeon/kms: additional default context regs for cayman
  drm/radeon/kms: add cayman CS check support
  drm/radeon/kms: add radeon_asic entry for cayman
  drm/radeon/kms: add cayman safe regs
  drm/radeon/kms/cayman: add asic init/startup/fini/suspend/resume functions
  drm/radeon/kms: add cayman asic reset support
  drm/radeon/kms: add support for cayman irqs
  drm/radeon/kms: add support for CP setup on cayman asics
  drm/radeon/kms: add support for cayman gart setup
  drm/radeon/kms: add gpu_init function for cayman
  drm/radeon/kms: add ucode loader for cayman
  drm/radeon/kms: add cayman chip family

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Added to existing evergreen CS checker.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For the CS checker.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Cayman is different enough from evergreen to warrant it's own functions.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Cayman asics have 3 ring buffers:
ring 0 supports both gfx and compute
rings 1 and 2 are compute only

At the moment we only support ring 0.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch sets up the gart in legacy mode.  We
probably want to switch to full VM mode at some point.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This may some work to get accel going.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The MC ucode is no longer loaded by the vbios
tables as on previous asics.  It now must be loaded
by the driver.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Cayman is DCE5 display plus a new 4-way shader block.
3D state programming is similar to evergreen.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's cleaned before saving and re-initialized after restoring.
So don't need to save/restore it. And also new chip has new address
for hardware status page register, don't write to old address.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

It is trivially computable from the real physical address so no need to
store both.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).

Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.

So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: NJan Niehusmann <jan@gondor.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

This reverts commit c4ff4b82.

Ted Ts'o reports:

 "TPM is working for me so I can log into employer's network in 2.6.37.
  It broke when I tried 2.6.38-rc6, with the following relevant lines
  from my dmesg:

  [   11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
  [   25.734114] tpm_tis 00:0b: Operation Timed out
  [   78.040949] tpm_tis 00:0b: Operation Timed out

  This caused me to get suspicious, especially since the _other_ TPM
  commit in 2.6.38 had already been reverted, so I tried reverting
  commit c4ff4b82: "TPM: Long default timeout fix".  With this commit
  reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: NTheodore Ts'o <tytso@mit.edu>
Acked-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This seems to be running stably on my test laptop, so hopefully the
reported hangs where just symptoms of other bugs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

I stumbled over this magic bit in the gen3 INSTPM:

Bit11 Interrupt-Based AGPBUSY# Enable:

‘0’ = Pending GMCH interrupts will not cause AGPBUSY# assertion.
‘1’ = Pending GMCH interrupts will cause AGPBUSY# assertion and hence
      can cause the CPU to exit C3.  There is no suppression of cacheable
      writes.

Note that in either case in C3 the interrupts are not lost. They will be
forwarded to the ICH when the GMCH is out of C3.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org

Using PM latency request turns out to be very fragile and only works for
some systems, depending upon the ACPI implementation. However, I've
stumbled across a promising bit in INSTPM: "Interrupt-Based AGPBUSY#".

This reverts commit b0b544cd.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

drivers/gpu/drm/i915/i915_irq.c: In function ‘ironlake_irq_postinstall’:
drivers/gpu/drm/i915/i915_irq.c:1618: warning: unused variable ‘pipe’
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This allows userspace to work out how many DBs there are
for conditional rendering to work.
Signed-off-by: NDave Airlie <airlied@redhat.com>