Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.

WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID

cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final

$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final

TPC config for channel 5180 mode 10

CTL             =  0x 0 Reg. Domain             = 58
Antenna Gain    =  0 Reg. Max Antenna Gain      =   0
Power Limit     = 60 Reg. Max Power             = 60
Num tx chains   =  2 Num supported rates        = 109

******************* CDD POWER TABLE ****************

No.  Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0    CCK      0x40        0          0
1    CCK      0x41        0          0
[...]
107  HTCUP    0x 0       46          46
108  HTCUP    0x 0       46          46

******************* STBC POWER TABLE ****************

No.  Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0    CCK      0x40        0          0
1    CCK      0x41        0          0
[...]
107  HTCUP    0x 0        46         46
108  HTCUP    0x 0        46         46

***********************************
TXBF not supported
**********************************

The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.

cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats

Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Added per tid sta counters for the following

- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211

All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.

These per tid stats can be enabled with tid bitmask through a debugfs
like below

 echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask

 tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames

The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats

Sample output:

 To enable rx stats for tid 0, 5 and 6,

 echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask

cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats

  		Driver Rx pkt stats per tid, ([tid] count)
                ------------------------------------------
MSDUs from FW                   [00] 2567        [05] 3178        [06] 1089
MSDUs unchained                 [00] 0           [05] 0           [06] 0
MSDUs locally dropped:chained   [00] 0           [05] 0           [06] 0
MSDUs locally dropped:filtered  [00] 0           [05] 0           [06] 0
MSDUs queued for mac80211       [00] 2567        [05] 3178        [06] 1089
MSDUs with error:fcs_err        [00] 0           [05] 0           [06] 2
MSDUs with error:tkip_err       [00] 0           [05] 0           [06] 0
MSDUs with error:crypt_err      [00] 0           [05] 0           [06] 0
MSDUs with error:peer_idx_inval [00] 0           [05] 0           [06] 0

A-MPDU num subframes upto 10    [00] 2567        [05] 3178        [06] 1087
A-MPDU num subframes 11-20      [00] 0           [05] 0           [06] 0
A-MPDU num subframes 21-30      [00] 0           [05] 0           [06] 0
A-MPDU num subframes 31-40      [00] 0           [05] 0           [06] 0
A-MPDU num subframes 41-50      [00] 0           [05] 0           [06] 0
A-MPDU num subframes 51-60      [00] 0           [05] 0           [06] 0
A-MPDU num subframes >60        [00] 0           [05] 0           [06] 0

A-MSDU num subframes 1          [00] 2567        [05] 3178        [06] 1089
A-MSDU num subframes 2          [00] 0           [05] 0           [06] 0
A-MSDU num subframes 3          [00] 0           [05] 0           [06] 0
A-MSDU num subframes 4          [00] 0           [05] 0           [06] 0
A-MSDU num subframes >4         [00] 0           [05] 0           [06] 0
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.

This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.

Fixes: 50f08edf ("ath9k: Switch to using mac80211 intermediate software queues.")
Cc: stable@vger.kernel.org
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NToke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.

Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Added a new debugfs file 'mids' to print the list of
virtual interfaces by MAC ID (MID). Allows mapping
between the internal MID used by FW and the actual
network interface used by the VIF. This is needed by
debugging tools.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.

More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

New FW which supports multiple virtual interfaces, reports
its allowed interface combinations using a special comment
record in the FW file. The format of the interface combinations
is similar to the kernel wiphy->iface_combinations.
When parsing FW file during module initialization, also parse
and validate the concurrency record, and initialize
wiphy->n_iface_combinations and wiphy->iface_combinations
accordingly.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For supporting multiple virtual interfaces in the future,
introduce a wil6210_vif structure which will hold per-VIF
data. Change the module initialization so wil6210_vif will
be part of net_device structure, and wireless_dev will be
embedded inside the wil6210_vif structure. This will allow
us to find the appropriate wil6210_vif structure when we
only have access to wireless_dev or net_device.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The wcn36xx_cancel_hw_scan method stops the hw scan and notify the
scan completion via ieee80211_scan_completed.
However, on scan offload cancellation, firmware sends a scan complete
indication, triggering a new call to ieee80211_scan_completed.
This leads to kernel warn since the scan has already been completed.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Ack timing generation has to be adapted for 5/10 MHz channels.
Do it by properly initializing ack shift field in TXSIFS
register. Ack shift assumes channel width of 2.5 Mhz so
value zero means 2.5 MHz, 1 is 5 MHz and so on.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The bitrate value for airtime calculation is specified for
full rates. We need to divide it for 5 and 10MHz channels to
get correct result.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pointer tq is initialized with &ah->ah_txq[queue] and then a few
lines later is re-assigned the same value, hence this duplicate
assignment is redundant and can be removed.

Cleans up clang warning:
drivers/net/wireless/ath/ath5k/qcu.c:326:25: warning: Value stored
to 'tq' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Preparation for a new QCA9377 firmware release. The new firmware release
requires more IRAM banks, hence update that on ath10k.

The IRAM banks promotion won't break any backwards compatibility, as those IRAM
banks were not getting used in previous firmware releases.
Signed-off-by: NRyan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

HIF power-on failure is applicable to each underlying
bus type. Fix log message for hif power on failure.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in debug error message text.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Whenever ath10k firmware discards a packet (HTT_TX_COMPL_STATE_DISCARD
flag), the skb is freed and mac80211 does not get feedback through
ieee80211_tx_status().

Instead, make sure that the IEEE80211_TX_STAT_ACK flag is disabled and
let the packet go through, like ath9k does.
Signed-off-by: NIgnacio Nunez Hernanz <nacho.nunez@aoifes.com>
[kvalo@codeaurora.org: rebase patch manually]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: NVenkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit 9ed4f916.

The commit introduced a regression that over read the ie with
the padding.

- the expected IE information

ath10k_pci 0000:03:00.0: found firmware features ie (1 B)
ath10k_pci 0000:03:00.0: Enabling feature bit: 6
ath10k_pci 0000:03:00.0: Enabling feature bit: 7
ath10k_pci 0000:03:00.0: features
ath10k_pci 0000:03:00.0: 00000000: c0 00 00 00 00 00 00 00

- the wrong IE with padding is read (0x77)

ath10k_pci 0000:03:00.0: found firmware features ie (4 B)
ath10k_pci 0000:03:00.0: Enabling feature bit: 6
ath10k_pci 0000:03:00.0: Enabling feature bit: 7
ath10k_pci 0000:03:00.0: Enabling feature bit: 8
ath10k_pci 0000:03:00.0: Enabling feature bit: 9
ath10k_pci 0000:03:00.0: Enabling feature bit: 10
ath10k_pci 0000:03:00.0: Enabling feature bit: 12
ath10k_pci 0000:03:00.0: Enabling feature bit: 13
ath10k_pci 0000:03:00.0: Enabling feature bit: 14
ath10k_pci 0000:03:00.0: Enabling feature bit: 16
ath10k_pci 0000:03:00.0: Enabling feature bit: 17
ath10k_pci 0000:03:00.0: Enabling feature bit: 18
ath10k_pci 0000:03:00.0: features
ath10k_pci 0000:03:00.0: 00000000: c0 77 07 00 00 00 00 00
Tested-by: NMike Lothian <mike@fireburn.co.uk>
Signed-off-by: NRyan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

as reported in:
https://github.com/qca/open-ath9k-htc-firmware/pull/71#issuecomment-361100070Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If device gone during chip reset, ar->normal_mode_fw.board is not
initialized, but ath10k_debug_print_hwfw_info() will try to access its
member, which will cause 'kernel NULL pointer' issue. This was found
using a faulty device (pci link went down sometimes) in a random
insmod/rmmod/other-op test.
To fix it, check ar->normal_mode_fw.board before accessing the member.

pci 0000:02:00.0: BAR 0: assigned [mem 0xf7400000-0xf75fffff 64bit]
ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
ath10k_pci 0000:02:00.0: failed to read device register, device is gone
ath10k_pci 0000:02:00.0: failed to wait for target init: -5
ath10k_pci 0000:02:00.0: failed to warm reset: -5
ath10k_pci 0000:02:00.0: firmware crashed during chip reset
ath10k_pci 0000:02:00.0: firmware crashed! (uuid 5d018951-b8e1-404a-8fde-923078b4423a)
ath10k_pci 0000:02:00.0: (null) target 0x00000000 chip_id 0x00340aff sub 0000:0000
ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
ath10k_pci 0000:02:00.0: firmware ver  api 0 features  crc32 00000000
...
BUG: unable to handle kernel NULL pointer dereference at 00000004
...
Call Trace:
 [<fb4e7882>] ath10k_print_driver_info+0x12/0x20 [ath10k_core]
 [<fb62b7dd>] ath10k_pci_fw_crashed_dump+0x6d/0x4d0 [ath10k_pci]
 [<fb629f07>] ? ath10k_pci_sleep.part.19+0x57/0xc0 [ath10k_pci]
 [<fb62c8ee>] ath10k_pci_hif_power_up+0x14e/0x1b0 [ath10k_pci]
 [<c10477fb>] ? do_page_fault+0xb/0x10
 [<fb4eb934>] ath10k_core_register_work+0x24/0x840 [ath10k_core]
 [<c18a00d8>] ? netlbl_unlhsh_remove+0x178/0x410
 [<c10477f0>] ? __do_page_fault+0x480/0x480
 [<c1068e44>] process_one_work+0x114/0x3e0
 [<c1069d07>] worker_thread+0x37/0x4a0
 [<c106e294>] kthread+0xa4/0xc0
 [<c1069cd0>] ? create_worker+0x180/0x180
 [<c106e1f0>] ? kthread_park+0x50/0x50
 [<c18ab4f7>] ret_from_fork+0x1b/0x28
 Code: 78 80 b8 50 09 00 00 00 75 5d 8d 75 94 c7 44 24 08 aa d7 52 fb c7 44 24 04 64 00 00 00
 89 34 24 e8 82 52 e2 c5 8b 83 dc 08 00 00 <8b> 50 04 8b 08 31 c0 e8 20 57 e3 c5 89 44 24 10 8b 83 58 09 00
 EIP: [<fb4e7754>]-
 ath10k_debug_print_board_info+0x34/0xb0 [ath10k_core]
 SS:ESP 0068:f4921d90
 CR2: 0000000000000004
Signed-off-by: NYu Wang <yyuwang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Commit 8da58553 ("ath9k: Use calibrated noise floor value
when available") introduced regression in ath9k_hw_getchan_noise
where per chain nominal noise floor has been taken instead default
for channel.
Revert to original default channel noise floor.

Fixes: 8da58553 ("ath9k: Use calibrated noise floor value when available")
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: NTobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.

Fixes: 703f261d ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: NYu Wang <yyuwang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: NRamon Fried <rfried@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Display per frequency calibration data in dump_modal
debugfs entry including reference power, voltage,
tx temperature and noise floor.

Example of chain 0 of OEM card (dump from modal_eeprom):
Chain 0
Freq	 ref	volt	temp	nf_Cal	nf_Pow	rx_temp
5180	-30	0	137	0	0	0
5320	-24	0	137	0	0	0
5500	-15	0	137	0	0	0
5620	-10	0	137	0	0	0
5700	-15	0	137	0	0	0
5745	-16	0	135	0	0	0
5785	-19	0	136	0	0	0
5825	-22	0	136	0	0	0

Example of a card with calibrated noise floor.
Chain 0
Freq	 ref	volt	temp	nf_Cal	nf_Pow	rx_temp
4890	-49	0	128	-107	-97	124
5100	-23	0	128	-101	-96	124
5180	-18	0	128	-101	-96	124
5300	-12	0	128	-102	-97	124
5500	-9	0	128	-101	-97	125
5640	-17	0	128	-101	-98	124
5785	-25	0	128	-101	-98	124
5940	-33	0	128	-106	-99	124
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AR9003 series allows to calibrate noise floor for different frequency
bins. Once it's done it's possible to get more accurate rssi/signal
values over whole frequency band at a given temperature.
The RSSI/signal accuracy reported by calibrated RF cards improves
from 6 to up to 2dB.

This could be interesting for application which require good signal
accuracy like roaming or mesh protocols.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AR9003 devices can have calibrated noise floor values
which can be used instead of hard coded one. Read them
from eeprom and save interpolated value in nf limits for
the current channel.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AR9003 factory calibration allows to use bigger EEPROM than
standard 1k without changing the default layout. Allow
probing of EEPROM at alternative address if initial check
for default fails.
The original ar9003 eeprom ops are still be used.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>