Only 7 bits are used for updating the brightness.  (register address :
A0h) So the max_brightness property of lm3530 should be set to 127.

On initializing registers, maximum initial brightness is limited to
'max_brightness'.

Division-by-two is removed on updating the brightness.  This arithmetic is
not necessary because the range of brightness is 0 ~ 127= .
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the PCA9633 I2C chip supporting four LEDs and 255 brightness
levels.

[akpm@linux-foundation.org: fix kcalloc() call]
[axel.lin@gmail.com: fix kcalloc parameters swapped]
Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Saves ~50 bytes text and speeds things up.

Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix it by assigning the lp5521_read return value.
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Cc: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For better readability, values of LP5521_REG_ENABLE register were
redefined= .  Additional definitions: LP5521_ENABLE_DEFAULT and
LP5521_ENABLE_RUN_PROGRAM= .

Use definition rather than hard code value.
: 0x3F -> 'LP5521_CMD_DIRECT'
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The lp5521 has autonomous operation mode without external control.
Using lp5521_platform_data, various led patterns can be configurable.
For supporting this feature, new functions and device attribute are
added.

Structure of lp5521_led_pattern: 3 channels are supported - red, green
and blue.  Pattern(s) of each channel and numbers of pattern(s) are
defined in the pla= tform data.  Pattern data are hexa codes which
include pattern commands such like set pwm, wait, ramp up/down, branch
and so on.

Pattern mode functions:
 * lp5521_clear_program_memory
	Before running new led pattern, program memory should be cleared.
 * lp5521_write_program_memory
	Pattern data updated in the program memory via the i2c.
 * lp5521_get_pattern
	Get pattern from predefined in the platform data.
 * lp5521_run_led_pattern
	Stop current pattern or run new pattern.
	Transition time is required between different operation mode.

Device attribute - 'led_pattern': To load specific led pattern, new device
attribute is added.

When the lp5521 driver is unloaded, stop current led pattern mode.

Documentation updated : description about how to define the led patterns
and example.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The value of CONFIG register(Addr 08h) is configurable.  For supporting
this feature, update_config is added in the platform data.  If
'update_config' is not defined, the default value is 'LP5521_PWRSAVE_EN |
LP5521_CP_MODE_AUTO | LP5521_R_TO_BATT'.

To define CONFIG register in the platform data, the bit definitions were
mo= ved to the header file.

Documentation updated : description about 'update_config' and example.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The name of each led channel can be configurable.  For the compatibility,
the name is set to default value(xx:channelN) when 'name' is not defined.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error.  This is obsolete meanwhile, the
core will do it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: NeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Just a small tidy-up.

1) There is a NULL dereference if the tca allocation fails.
2) The call to cancel_work_sync() isn't needed because we haven't
   scheduled any work.
3) The call to i2c_set_clientdata() isn't needed because the core
   handles that automatically if probe() fails.
4) I added some curly braces for style reasons.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"reseting" -> "resetting"
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add platform driver for the Soekris Engineering net5501 single-board
computer.  Probes well-known locations in ROM for BIOS signature
to confirm correct platform.  Registers 1 LED and 1 GPIO-based
button (typically used for soft reset).
Signed-off-by: NPhilip Prindeville <philipp@redfish-solutions.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Removed Kconfig and Makefile detritus from drivers/leds/]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0.  This does not make sense.  I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.

Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter.  Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for leds on Bachmann's ot200 visualisation device.  The
device has three leds on the back panel (led_err, led_init and led_run)
and can handle up to seven leds on the front panel.

The driver was written by Linutronix on behalf of Bachmann electronic
GmbH.  It incorporates feedback from Lars-Peter Clausen

[akpm@linux-foundation.org: add dependency on HAS_IOMEM]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Saves a small amount of code and systematically eliminates leaks.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Saves a small amount of code and systematically eliminates leaks.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The LED id begins from 0.  Thus the maximum number of leds should be
MC13783_LED_MAX + 1.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NPhilippe Retornaz <philippe.retornaz@epfl.ch>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

TI's TCA6507 is the LED driver in the GTA04 Openmoko motherboard.  The
driver provides full support for brightness levels and hardware blinking.

This driver can drive each of 7 outputs as an LED or a GPIO output,
and provides hardware-assist blinking.

[akpm@linux-foundation.org: fix __mod_i2c_device_table alias]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NNeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use gpio_request_one() instead of multiple gpiolib calls.  This also
simplifies error handling a bit.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Simon Guinot <sguinot@lacie.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Kim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Factor out some boilerplate code for spi driver registration into
module_spi_driver.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Haojian Zhuang <hzhuang1@marvell.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Factor out some boilerplate code for i2c driver registration
into module_i2c_driver.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Haojian Zhuang <hzhuang1@marvell.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Factor out some boilerplate code for platform driver registration into
module_platform_driver.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <hzhuang1@marvell.com>		[led-88pm860x.c]
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch enables LED controller in MAX8997 PMIC.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.

The sysdev code will be going away soon, so this include needs to be
removed no matter what.

Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>

Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Revert commit 6123b0e2.

The problem this patch intends to solve has alreadqy been fixed by
commit 7a5caabd ("drivers/leds/ledtrig-timer.c: fix broken sysfs
delay handling").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sure that the reset is successful by issuing a dummy read to R
channel current register and check its default value.  On some platforms,
without this dummy read, any further access to {R/G/B}_EXEC will not have
any impact.

[akpm@linux-foundation.org: fix up code comment]
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: NNaga Radhesh <naga.radheshy@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.

Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:

  OFF
  hardware blinking
  software blinking
  hardware blinking

does not leave the software blinking timer active.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When calling the hardware blinking function implemented by blink_set(),
the delay_on and delay_off values are not preserved across calls.

Fix that and make the "timer" trigger work as expected when hardware
blinking is available.

BEFORE the fix:
  $ cd /sys/class/leds/someled
  $ echo timer > trigger
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_on
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_off
  $ cat delay_on delay_off
  0
  0

AFTER the fix:
  $ cd /sys/class/leds/someled
  $ echo timer > trigger
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_on
  $ cat delay_on delay_off
  100
  0
  $ echo 100 > delay_off
  $ cat delay_on delay_off
  100
  100
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I get the following warning:

------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1559 __gpio_get_value+0x90/0x98()
Modules linked in:
Call Trace:
[<ffffffff81440950>] dump_stack+0x8/0x34
[<ffffffff81141478>] warn_slowpath_common+0x78/0xa0
[<ffffffff812f0958>] __gpio_get_value+0x90/0x98
[<ffffffff81434f04>] create_gpio_led+0xdc/0x194
[<ffffffff8143524c>] gpio_led_probe+0x290/0x36c
[<ffffffff8130e8b0>] driver_probe_device+0x78/0x1b0
[<ffffffff8130eaa8>] __driver_attach+0xc0/0xc8
[<ffffffff8130d7ac>] bus_for_each_dev+0x64/0xb0
[<ffffffff8130e130>] bus_add_driver+0x1c8/0x2a8
[<ffffffff8130f100>] driver_register+0x90/0x180
[<ffffffff81100438>] do_one_initcall+0x38/0x160

---[ end trace ee38723fbefcd65c ]---

My GPIOs are on an I2C port expander, so we must use the *_cansleep()
variant of the GPIO functions.  This is was not being done in
create_gpio_led().

We can change gpio_get_value() to gpio_get_value_cansleep() because it is
only called from the platform_driver probe function, which is a context
where we can sleep.

Only tested on my gpio_cansleep() system, but it seems safe for all
systems.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NTrent Piepho <tpiepho@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the comments in include/linux/init.h:

"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."

We have __devexit annotation for lm3530_remove(), so add __devexit_p to
the `struct i2c_driver'.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If lp5521_read fails, engine_state variable is not initialized.
If lp5521_read fails, we should return error.
This patch fixes below warning.

  CC      drivers/leds/leds-lp5521.o
drivers/leds/leds-lp5521.c: In function 'lp5521_set_engine_mode':
drivers/leds/leds-lp5521.c:168: warning: 'engine_state' may be used uninitialized in this function

[akpm@linux-foundation.org: remove unneeded "ret |="]
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error.  This is obsolete meanwhile, the core
will do it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The memory for struct led_trigger should be kfreed in the
led_trigger_register() error path.  Also this function should return NULL
on error.
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>