- 13 8月, 2009 1 次提交
-
-
由 Magnus Damm 提交于
Convert the Migo-R board code to register devices at arch_initcall() time instead of __initcall(). This fix unbreaks migor_ts touch screen driver support. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 17 6月, 2009 2 次提交
-
-
由 Guennadi Liakhovetski 提交于
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Guennadi Liakhovetski 提交于
Unify i2c camera device platform data to point to struct soc_camera_link for a smooth transition to soc-camera as a platform driver. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 11 6月, 2009 1 次提交
-
-
由 Magnus Damm 提交于
This patch adds mode pin configuration and a machvec structure to Migo-R. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 02 4月, 2009 1 次提交
-
-
由 Paul Mundt 提交于
Follows the same change as per ap325rxa, which was inadvertently omitted. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 30 3月, 2009 1 次提交
-
-
由 Guennadi Liakhovetski 提交于
All soc-camera camera and host drivers must specify supported data signal polarity, after all drivers are fixed, we'll add a suitable test to soc_camera_bus_param_compatible(). Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 10 3月, 2009 1 次提交
-
-
由 Magnus Damm 提交于
If CONFIG_PM is set, let Migo-R LEDs show sleep states. D11 will show STATUS0 and D12 PDSTATUS. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 21 1月, 2009 4 次提交
-
-
由 Magnus Damm 提交于
This patch adds CN9 MMC support for MigoR using the mmc_spi driver on top of the bitbanging spi_gpio driver. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Kuninori Morimoto 提交于
Migo-R can use ov772x camera driver in Linux 2.6.29. Therefore, soc_camera_platform setting is no longer needed. This patch removes it. Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 22 12月, 2008 7 次提交
-
-
由 Magnus Damm 提交于
Enable LCDC deferred io on Migo-R using 1s delay. As with other deferred io frame buffers user space code should use fsync() on the frame buffer device to trigger an update. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add LCDC interrupt resources for AP325 and Migo-R. The LCDC driver does not require interrupts at this point, but changes such as one-shot SYS mode using deferred io, and wait-for-vblank will both need this. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
This kills off the special Migo-R machvec, as nothing is using it. By default this will switch to using the generic machvec, which provides the same functionality. This saves us a bit of space in the machvec section. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add reset delay for the ov772x device on Migo-R. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add clock framework support to the lcdc driver and adjust the board specific code accordingly. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add clock framework support to the sh_mobile ceu and adjust the board specific code accordingly. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add clock framework support to the sh_mobile keysc driver and adjust the board specific code accordingly. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 22 10月, 2008 1 次提交
-
-
由 Magnus Damm 提交于
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R. This improves the camera picture quality on Panel Board V2.1. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 21 10月, 2008 2 次提交
-
-
由 Magnus Damm 提交于
Update the ov772x byte sequence to enable byte swap. This to reflect the recent CEU driver change to follow incoming byte order. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Guennadi Liakhovetski 提交于
Fix Migo-R compile breakage caused by incomplete merge. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 20 10月, 2008 4 次提交
-
-
由 Paul Mundt 提交于
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Improve Migo-R ethernet performance by reducing smc91x overruns. This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
This patch enables the GPIO code on Migo-R and converts the code from register based pinmux configuration to GPIO based pin by pin setup. Fix whitespace damage while at it and add 2 LEDs and export them to user space. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 01 10月, 2008 1 次提交
-
-
由 Paul Mundt 提交于
This provides a workaround for users of sh_mobile_lcdcfb that don't define HAVE_CLK and have otherwise sane clock initialization. At the same time, move the sh_mobile_lcdc.h header to include/video/. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 11 8月, 2008 1 次提交
-
-
由 Magnus Damm 提交于
Export the LCD panel size for sh_mobile_lcdc boards. This allows us to perform dpi and screen aspect ratio calculations in user space. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 29 7月, 2008 2 次提交
-
-
由 Magnus Damm 提交于
Fix recently introduced I2C build breakage on AP325RXA and Migo-R. Reported-by: NAdrian Bunk <bunk@kernel.org> Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
This flattens out the board directories in to individual mach groups, we will use this for getting rid of unneeded directories, simplifying the build system, and becoming more coherent with the refactored arch/sh/include topology. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 28 7月, 2008 3 次提交
-
-
由 Magnus Damm 提交于
Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add WVGA and QVGA LCD panel support to Migo-R. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Use clk_always_enable() on the sh7722 processor and in the board code for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register definitions. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 13 7月, 2008 1 次提交
-
-
由 Eric Miao 提交于
IRQ trigger type can be specified in the IRQ resource definition by IORESOURCE_IRQ_*, we need only one way to specify this. This also fixes the following small issue: To allow dynamic support for multiple platforms, when those relevant macros are not defined for one specific platform, the default case will be: - SMC_DYNAMIC_BUS_CONFIG defined - and SMC_IRQ_FLAGS = IRQF_TRIGGER_RISING While if "irq_flags" is missing when defining the smc91x_platdata, usually as follows: static struct smc91x_platdata xxxx_smc91x_data = { .flags = SMC91X_USE_XXBIT, }; The lp->cfg.irq_flags will always be overriden by the above structure (due to a memcpy), thus rendering lp->cfg.irq_flags to be "0" always. (regardless of the default SMC_IRQ_FLAGS or IORESOURCE_IRQ_* flags) Fixes this by forcing to use IORESOURCE_IRQ_* flags if present, and make the only user of smc91x_platdata.irq_flags (renesas/migor) to use IORESOURCE_IRQ_*. Signed-off-by: NEric Miao <eric.miao@marvell.com> Acked-by: NNicolas Pitre <nico@cam.org> Acked-by: NJeff Garzik <jgarzik@pobox.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 5月, 2008 1 次提交
-
-
由 Magnus Damm 提交于
Select smc91x bus width and irg flags using platform data for MigoR now when the smc91x header file is in place. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 30 4月, 2008 1 次提交
-
-
由 Jean Delvare 提交于
Based on earlier work by Jon Smirl and Jochen Friedrich. Update most new-style i2c drivers to use standard module aliasing instead of the old driver_name/type driver matching scheme. I've left the video drivers apart (except for SoC camera drivers) as they're a bit more diffcult to deal with, they'll have their own patch later. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Jon Smirl <jonsmirl@gmail.com> Cc: Jochen Friedrich <jochen@scram.de>
-
- 19 4月, 2008 5 次提交
-
-
由 Magnus Damm 提交于
Add support for the migor_ts touch panel to the MigoR board. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add support for the rs5c372b RTC chip to MigoR. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Enable the sh7722 I2C controller on the MigoR board. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add NAND flash support to the MigoR board by giving board specific data to the gen_nand platform driver. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Magnus Damm 提交于
Add NOR flash support to the MigoR board by giving board specific data to the physmap-flash platform driver. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-