- 30 1月, 2015 1 次提交
-
-
由 Baruch Siach 提交于
cx92755.dtsi describes CX92755 on chip peripherals. cx92755_equinox.dts describes the Equinox evaluation board for the CX92755 SoC. Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 27 1月, 2015 1 次提交
-
-
由 Nicolas Ferre 提交于
The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config options may be removed in the near future. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 26 1月, 2015 2 次提交
-
-
由 FUKAUMI Naoki 提交于
This add support for Rayeager PX2, Rockchip PX2 based development board made by ChipSPARK. Signed-off-by: NFUKAUMI Naoki <naobsd@gmail.com> Tested-by: NAndy Yan <andy.yan@rock-chips.com> Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
-
由 FUKAUMI Naoki 提交于
This adds support for Firefly-RK3288, Rockchip RK3288 based development boards made by Firefly. There are 2 dts for 2 versions of the board. rk3288-firefly-beta.dts is for the beta version, rk3288-firefly.dts is for the mass production version. Signed-off-by: NFUKAUMI Naoki <naobsd@gmail.com> [removed gmac reference, due to the gmac node going through the net-tree] Tested-by: NHeiko Stuebner <heiko@sntech.de> Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
-
- 24 1月, 2015 2 次提交
-
-
由 Olof Johansson 提交于
Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Hans de Goede 提交于
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD Cc: Mark Janssen <maniac@maniac.nl> Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 22 1月, 2015 2 次提交
-
-
由 Christoph Junghans 提交于
The pogoplug differs from the SheevaPlug only by a few details, but especially in the led assignments. This patch was tested under Gentoo Linux and is based on dts files from Arch Linux ARM and OpenWrt. Suggested-by: NFelix Kaechele <heffer@fedoraproject.org> Suggested-by: NOleg Rakhmanov <moonman.ca@gmail.com> Signed-off-by: NChristoph Junghans <ottxor@gentoo.org> [Andrew Lunn <andrew@lunn.ch>: Fixed subject line] Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
-
由 Wang Long 提交于
Add dts file for Hisilicon hip01 ca9x2 board Signed-off-by: NWang Long <long.wanglong@huawei.com> Signed-off-by: NWei Xu <xuwei5@hisilicon.com> [olof: Folded in smp enable-method from a different patch] Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 21 1月, 2015 10 次提交
-
-
由 Aleksei Mamlin 提交于
This patch add support for Marsboard A10 board. The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND, micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port, 1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic, it does not have a pmic at all. Board also have 2 expansion 70 pin headers. Signed-off-by: NAleksei Mamlin <mamlinav@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG) and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic, the axp152. For more details see: http://linux-sunxi.org/Semitime_g2Signed-off-by: NHans de Goede <hdegoede@redhat.com> [Maxime: Changed the compatible and node names labels] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic. For more details see: http://linux-sunxi.org/Rikomagic_mk802iiSigned-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features 512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not use the AXP209 pmic, it does not have a pmic at all. For more details see: http://linux-sunxi.org/Rikomagic_mk802Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash, microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out, stereo speakers, front & back camera and usb wifi. It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the tablet. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate dtb file since some gpio-s surrounding the wlan/bluetooth are different, it uses different camera sensors, and different DRAM timings. Note that atm neither the wlan/bluetooth nor the camera are supported, so atm their is no difference between the dts files, but because of the different DRAM timings there are already separate u-boot configs for the 2 different versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND, rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG controller), ethernet, 3.5 mm jack with a/v out and hdmi out. Note it has no sdcard slot and therefore can only be fel booted. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
由 Dan Haab 提交于
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only unusual thing in its DTS file is "ubi" partition on NAND flash. Signed-off-by: NDan Haab <dhaab@luxul.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
- 20 1月, 2015 3 次提交
-
-
由 Olof Johansson 提交于
The file is roughly sorted alphabetically (with some exceptions where old options have been split in two), so alphascale should go at the top instead of at the bottom. Also linewrap like other entries have been lately. Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Oleksij Rempel 提交于
for now it is wary basic SoC description with most important IPs needed to make this device work Signed-off-by: NOleksij Rempel <linux@rempel-privat.de> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Tony Lindgren 提交于
This allows booting the device with basic functionality. Note that at least on my revision c board the DDR3 does not seem to work properly and only some of the memory can be reliably used. Also, the mainline u-boot does not seem to properly initialize the ethernet, so I've been using the old TI u-boot at: http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 16 1月, 2015 1 次提交
-
-
由 Maxime COQUELIN 提交于
B2199 HDK is the reference board for STiH418 SoC. It has the following characteristics: - 3GB DDR3 - 8GB eMMC / SD-Card slot - 32MB NOR Flash - 1 x Gbit Ethernet - 1 x USB3.0 port - 2 x USB2.0 ports - 1 x Sata or Mini-PCIe port - 1 x WiFi 802.11ac (Quantenna) - 1 x HDMI out - 1 x HDMI in - 1 x SPDIF Reviewed-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
- 13 1月, 2015 2 次提交
-
-
由 Zhiwu Song 提交于
CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens of MARCOs, in each MARCO, there are dozens of hardware modules. Signed-off-by: NZhiwu Song <Zhiwu.Song@csr.com> Signed-off-by: NHao Liu <Hao.Liu@csr.com> Signed-off-by: NBarry Song <Baohua.Song@csr.com> Acked-by: NArnd Bergmann <arnd@arndb.de>
-
由 Peter Robinson 提交于
A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained definitions whether it be sub ARCH or SOC definitions. The device tree blobs should only be built if the specific option is enabled that supports that device or it might be that there's an expectation that the device is supported when in actual fact it's not. This ensures only the relevant bits are built. Also standardised the line break between the arch/soc definitions and the dtbs to be on separate lines for better consistency as per feedback. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: NLucas Stach <l.stach@pengutronix.de> Acked-by: NThierry Reding <treding@nvidia.com> Acked-by: NStephen Warren <swarren@nvidia.com> Acked-by: NShawn Guo <shawn.guo@freescale.com> [olof: Fixed stray \ in one of the IMX rules] Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 12 1月, 2015 1 次提交
-
-
由 Sjoerd Simons 提交于
Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is kept the same as the vendors naming, which means it's prefixed with exynos5422 instead of exynos5800 as the SoC name even though it includes the exyno5800 dtsi. Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk> Tested-by: NKevin Hilman <khilman@linaro.org> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
- 11 1月, 2015 1 次提交
-
-
由 Barry Song 提交于
MARCO will not be supported any more. it has been replaced by CSR atlas7. Signed-off-by: NBarry Song <Baohua.Song@csr.com> Acked-by: NArnd Bergmann <arnd@arndb.de>
-
- 09 1月, 2015 3 次提交
-
-
由 Gregory CLEMENT 提交于
The A388-GP is a board produced by Marvell that holds - 1 PCIe slot - 2 mini PCIe slot (one of them is multiplexed with the PCIe slot, muxing is selected through the GPIO expander) - 1 16MB SPI-NOR - 2 Gigabit Ethernet ports - 4 SATA ports (2 of them are multiplexed with the mini PCIe slots, muxing is selected through the GPIO expander) - 1 SDIO slot - 1 USB3 port - 2 USB2 port - 2 GPIO/interrupts expander on I2C Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
-
由 Gregory CLEMENT 提交于
This SoC belongs to the Armada 38x family. The main difference with the Armada 385 is that the 388 can handle two more SATA ports. Currently the consequence is the use of a different compatible string for the pinctrl node, in order to be able to use the pins associated to this 2 new SATA ports. The second SATA controller has also been moved from the armada38x.dtsi as it it specific to the Armada388 version. In the same time the Armada385 DB and Armada 385 RD board have been renamed in the 388 one and now include the armada-388.dtsi file. AS both of them have 4 SATA ports the SoC used on them were wrongly described. Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
-
由 Maxime Ripard 提交于
The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage. [gregory.clement@free-electrons.com: switch the license to the dual X11/GPL with the agreement of the author] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
-
- 08 1月, 2015 1 次提交
-
-
由 Felipe Balbi 提交于
The AM437x Industrial Development Kit (IDK) is an application development platform targeted at industrial communication and control applications. It comes with a 3-phase motor driver, PROFINET, PROFIBUS and a few other industrial communication interfaces. The board has 1GiB of DDR3 RAM, QSPI NOR flash, a 100% discrete power design (no PMIC) and an on-board 2MP camera (not supported with Linux as of this writing). Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 06 1月, 2015 2 次提交
-
-
由 Robert Nelson 提交于
For more information about the Udoo boards: http://www.udoo.org/Signed-off-by: NRobert Nelson <robertcnelson@gmail.com> Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Evgeni Dobrev 提交于
This patch adds support for Seagate BlackArmor NAS220. The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has 32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two USB 2.0 ports, two buttons and three LEDs. There is a serial port available on the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND). The only functionality still not implemented is the bi-color led on the front panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high results in blue color. The third led is wired to show the SATA activity on the two drives. Signed-off-by: NEvgeni Dobrev <evgeni@studio-punkt.com> Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
-
- 05 1月, 2015 1 次提交
-
-
由 Anson Huang 提交于
Add basic i.MX6SoloX Sabre Auto board support, currently only debug UART and uSDHC are supported on this board. Signed-off-by: NAnson Huang <b20788@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 21 12月, 2014 2 次提交
-
-
由 Ulrich Hecht 提交于
Makes sure the dtb is built for multiplatform builds. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Lager legacy support level is same as the DT case so remove the legacy code and force people to move over to using Multiplatform and DT. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> [Remove lager_defconfig and don't build the dtb for legacy kernels] Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 05 12月, 2014 4 次提交
-
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
-
- 01 12月, 2014 1 次提交
-
-
由 Peter Crosthwaite 提交于
Add a DTS describing the Digilent ZYBO board. Similar to ZED but with a 50MHz crystal instead of 33MHz. Acked-by: NSoren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-