Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This adds the new transactional memory archtected state to the signal context
in both 32 and 64 bit.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This hooks the new transactional memory code into context switching, FP/VMX/VMX
unavailable and exception return.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We do lazy FP but not lazy TM (ie. userspace starts with MSR TM=1 FP=0).  Hence
if userspace does an FP instruction during a transaction, we'll take an
fp unavailable exception.

This adds functions needed to handle this case.  We have to inject the current
FP state into the checkpoint so that the hardware can decide what to do with
the transaction.  We can't inject only the FP so we have to do a full treclaim
and recheckpoint to inject just the FP state.  This will cause the transaction
to be marked as aborted by the hardware.

This just add the routines needed to do this for FP, VMX and VSX.  It doesn't
hook them into the rest of the code yet.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These should never happen since we always turn on MSR TM when in userspace. We
don't do lazy TM.

Hence if we hit this, we barf and kill the task as something's gone horribly
wrong.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes

When we switch out a task, we need to save both the checkpointed and the
speculated state into the thread struct.

Similarly when we are switching in a task we need to load both the checkpointed
and speculated state.  If the task was using FP, we non-lazily reload both the
original and the speculative FP register states.  This is because the kernel
doesn't see if/when a TM rollback occurs, so if we take an FP unavoidable
later, we are unable to determine which set of FP regs need to be restored.

This simply adds these functions.  It doesn't hook them into the existing code
yet.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This adds functions to restore the state of the FP/VSX registers from
what's stored in the thread_struct.  Two version for FP/VSX are required
since one restores them from transactional/checkpoint side of the
thread_struct and the other from the speculated side.

Similar functions are added for VMX registers.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Here we add the helper functions to be used when context switching.  These
allow us to fully reclaim and recheckpoint a transaction.

We introduce a new paca field called tm_scratch to help us store away register
values when doing the low level tm reclaim register save.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add transactional memory paca scratch register to show_regs.  This is useful
for debugging.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Defines for MSR bits and transactional memory related SPRs TFIAR, TEXASR and
TEXASRU.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This adds new macros for saving and restoring checkpointed architected state
from and to the thread_struct.

It also adds some debugging macros for when your brain explodes trying to debug
your transactional memory enabled kernel.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Set of new archtected state for saving away on context switch.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Here we define the new instructions we need for transactional memory in the
kernel.  This is so we can support compiling with binutils that don't support
the new transactional memory instructions.

Transactional memory results in two sets of architected state (GPRs/VSRs
etc).

treclaim allows us to read the checkpointed state (from the tbegin) so that we
can store it away on a context switch.  It does this by overwriting the exiting
architected state, so you have to save that away before you treclaim.  treclaim
will also abort a transaction, so you can give a register value which contains
an abort reason.

trecheckpoint allows us to inject into the checkpointed state as if it were at
the tbegin.  It does this by copying the current architected state into the
checkpointed state.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 466921c5 we added a hack to set the paca data_offset to zero so
that per-cpu accesses would work on the boot cpu prior to per-cpu areas
being setup. This fixed a problem with lockdep touching per-cpu areas
very early in boot.

However if we combine CONFIG_LOCK_STAT=y with any of the PPC_EARLY_DEBUG
options, we can hit the same problem in udbg_early_init(). To avoid that
we need to set the data_offset of the boot_paca also. So factor out the
fixup logic and call it for both the boot_paca, and "the paca of the
boot cpu".
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Tested-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The powerpc boot_paca symbol is now only used within the
early_setup() routine, so move it from its global definition
into early_setup().
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

To allow more control of the verbosity of ps3_result() add a check
for the preprocessor macro PS3_VERBOSE_RESULT that builds a verbose
verion of the ps3_result() routine.
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a413f474 ("powerpc: Disable relocation on exceptions whenever
PR KVM is active") added calls to pSeries_disable_reloc_on_exc() and
pSeries_enable_reloc_on_exc() to book3s_pr.c, and added declarations
of those functions to <asm/hvcall.h>, but didn't add an include of
<asm/hvcall.h> to book3s_pr.c.  64-bit kernels seem to get hvcall.h
included via some other path, but 32-bit kernels fail to compile with:

arch/powerpc/kvm/book3s_pr.c: In function ‘kvmppc_core_init_vm’:
arch/powerpc/kvm/book3s_pr.c:1300:4: error: implicit declaration of function ‘pSeries_disable_reloc_on_exc’ [-Werror=implicit-function-declaration]
arch/powerpc/kvm/book3s_pr.c: In function ‘kvmppc_core_destroy_vm’:
arch/powerpc/kvm/book3s_pr.c:1316:4: error: implicit declaration of function ‘pSeries_enable_reloc_on_exc’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[2]: *** [arch/powerpc/kvm/book3s_pr.o] Error 1
make[1]: *** [arch/powerpc/kvm] Error 2
make: *** [sub-make] Error 2

This fixes it by adding an include of hvcall.h.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The CFAR (Come-From Address Register) is a useful debugging aid that
exists on POWER7 processors.  Currently HV KVM doesn't save or restore
the CFAR register for guest vcpus, making the CFAR of limited use in
guests.

This adds the necessary code to capture the CFAR value saved in the
early exception entry code (it has to be saved before any branch is
executed), save it in the vcpu.arch struct, and restore it on entry
to the guest.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Some of the interrupt vectors on 64-bit POWER server processors are
only 32 bytes long, which is not enough for the full first-level
interrupt handler.  For these we currently just have a branch to an
out-of-line handler.  However, this means that we corrupt the CFAR
(come-from address register) on POWER7 and later processors.

To fix this, we split the EXCEPTION_PROLOG_1 macro into two pieces:
EXCEPTION_PROLOG_0 contains the part up to the point where the CFAR
is saved in the PACA, and EXCEPTION_PROLOG_1 contains the rest.  We
then put EXCEPTION_PROLOG_0 in the short interrupt vectors before
we branch to the out-of-line handler, which contains the rest of the
first-level interrupt handler.  To facilitate this, we define new
_OOL (out of line) variants of STD_EXCEPTION_PSERIES, etc.

In order to get EXCEPTION_PROLOG_0 to be short enough, i.e., no more
than 6 instructions, it was necessary to move the stores that move
the PPR and CFAR values into the PACA into __EXCEPTION_PROLOG_1 and
to get rid of one of the two HMT_MEDIUM instructions.  Previously
there was a HMT_MEDIUM_PPR_DISCARD before the prolog, which was
nop'd out on processors with the PPR (POWER7 and later), and then
another HMT_MEDIUM inside the HMT_MEDIUM_PPR_SAVE macro call inside
__EXCEPTION_PROLOG_1, which was nop'd out on processors without PPR.
Now the HMT_MEDIUM inside EXCEPTION_PROLOG_0 is there unconditionally
and the HMT_MEDIUM_PPR_DISCARD is not strictly necessary, although
this leaves it in for the interrupt vectors where there is room for
it.

Previously we had a handler for hypervisor maintenance interrupts at
0xe50, which doesn't leave enough room for the vector for hypervisor
emulation assist interrupts at 0xe40, since we need 8 instructions.
The 0xe50 vector was only used on POWER6, as the HMI vector was moved
to 0xe60 on POWER7.  Since we don't support running in hypervisor mode
on POWER6, we just remove the handler at 0xe50.

This also changes denorm_exception_hv to use EXCEPTION_PROLOG_0
instead of open-coding it, and removes the HMT_MEDIUM_PPR_DISCARD
from the relocation-on vectors (since any CPU that supports
relocation-on interrupts also has the PPR).
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Cell processor doesn't support relocation-on interrupts, so we
don't need relocation-on versions of the interrupt vectors that are
purely Cell-specific.  This removes them.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds support for enabling and context switching the Target
Address Register in Power8. The TAR is a new special purpose register
that can be used for computed branches with the bctar[l] (branch
conditional to TAR) instruction in the same manner as the count and link
registers.
Signed-off-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

pseries/iommu: remove DDW on kexec

We currently insert a property in the device-tree when we successfully
configure DDW for a given slot. This was meant to be an optimization to
speed up kexec/kdump, so that we don't need to make the RTAS calls again
to re-configured DDW in the new kernel.

However, we end up tripping a plpar_tce_stuff failure on kexec/kdump
because we unconditionally parse the ibm,dma-window property for the
node at bus/dev setup time. This property contains the 32-bit DMA window
LIOBN, which is distinct from the DDW window's. We pass that LIOBN (via
iommu_table_init -> iommu_table_clear -> tce_free ->
tce_freemulti_pSeriesLP) to plpar_tce_stuff, which fails because that
32-bit window is no longer present after
25ebc45b ("powerpc/pseries/iommu: remove
default window before attempting DDW manipulation").

I believe the simplest, easiest-to-maintain fix is to just change our
initcall to, rather than detecting and updating the new kernel's DDW
knowledge, just remove all DDW configurations. When the drivers
re-initialize, we will set everything back up as it was before.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The parameter is unused, and complicates a following fix. Just remove
it.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It seems, we're fine with just annotating the two functions.
Thus, this fixes the following build warnings on ppc64:

WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1664):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.

WARNING: arch/powerpc/sysdev/built-in.o(.text+0x6044):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.

WARNING: arch/powerpc/kernel/built-in.o(.text+0x2db30):
The function .start_secondary() references
the function __cpuinit .vdso_getcpu_init().
This is often because .start_secondary lacks a __cpuinit
annotation or the annotation of .vdso_getcpu_init is wrong.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are now two kinds of DMA windows that might be presented by
PowerVM DDW support -- huge windows (that can map all of system memory
regardless of the LPAR configuration) and non-huge windows (which
can't). They are implemented slightly differently in PowerVM, and thus
have different characteristics. The most obvious is that slot isolate
doesn't clear the TCEs/window for us with non-huge windows. Thus, when a
DLPAR operation occurs on a slot using a non-huge window, TCEs are still
present (the notifier chain doesn't currently remove them explicitly)
and the DLPAR fails. Fix this by calling remove_ddw() first, which will
unmap the DDW TCEs.

Note: a corresponding change to drmgr is needed to actually successfully
DLPAR, such that the device-tree update (which causes the notifier chain
to fire) occurs before slot isolate.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

tce_clearrange_multi_pSeriesLP is attempting to iterate over all TCEs in
a given range. However, is it not advancing the dma_offset value passed
to plpar_tce_stuff via the next value. This prevents DLPAR from
completing, because TCEs are still present at slot isolation time.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Change the hardware breakpoint code so that we can support wider ranged
breakpoints.

This means both ptrace and perf hardware breakpoints can use upto 512 byte long
breakpoints when using the DAWR and only 8 byte when using the DABR.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.

Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event

If we disable a perf event because we exceeded the specified ->event_limit,
power_pmu_stop() sets the PERF_HES_STOPPED flag on the event.

If the application then re-enables the event using PERF_EVENT_IOC_ENABLE
ioctl, we don't ever clear this STOPPED flag. Consequently, the user space
is never notified of the event.

Following message has more background and test case.

    http://lists.eecs.utk.edu/pipermail/ptools-perfapi/2012-October/002528.html

Used the following test cases to verify that this patch works on latest PAPI.

	$ papi.git/src/ctests/nonthread PAPI_TOT_CYC@5000000

	$ papi.git/src/ctests/overflow_single_event

Changelog[v2]:
	- [Paul Mackerras] Also clear PERF_HES_UPTODATE flag since we are
	  restarting the event; cleanup comments and patch description.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use local_paca directly in macro SHARED_PROCESSOR, as all processors
have the same value for the field shared_proc, so we don't need care
racy here.
Reported-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.

Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).

The relevant device-tree looks like this:

	gpio0: gpio@130000 {
		compatible = "fsl,qoriq-gpio";
		reg = <0x130000 0x1000>;
		interrupts = <55 2 0 0>;
		#gpio-cells = <2>;
		gpio-controller;

		/* Allows powering off the system via GPIO signal. */
		gpio-halt@27 {
			compatible = "sgy,gpio-halt";
			gpios = <&gpio0 27 0>;
			interrupts = <8 1 0 0>;
		};
	};

Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.

Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().

As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: NBen Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While this should be harmless now that distribute_irqs
obeys MPIC_SINGLE_DEST_CPU, there's no reason to enable this
on mpc85xx/mpc86xx since MPIC_SINGLE_DEST_CPU will always be set.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Previously we were setting an illegal configuration on mpc85xx
MPICs if CONFIG_IRQ_ALL_CPUS is enabled (which for some reason it is
in mpc85xx_smp_defconfig).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have a mix of decimal and hex here, so lets make them consistently
hex.  Also, strace will print them in hex if it can't decode them, so
having them in hex here makes it easier to match up.

No functional change.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The only persistent change made by this loop is calling
memblock_set_node() once for each memblock, which is not useful (and has
no effect) as memblock_set_node() is not called with any
memblock-specific parameters.

Subsistute a single memblock_set_node().
Signed-off-by: NCody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Merge "merge" branch to bring in various bug fixes that are
going into 3.8