The coalesce settings behave badly when changing just one value:

... # ethtool -c eth0
rx-usecs: 249
... # ethtool -C eth0 tx-usecs 250
... # ethtool -c eth0
rx-usecs: 248

This occurs due to rounding errors when calculating the microseconds
value - the divisons round down.  This causes (eg) the rx-usecs to
decrease by one every time the tx-usecs value is set as per the above.

Fix this by making the divison round-to-nearest.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'create_root_ns()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be
set to 0, not 6, on the Qualcomm Technologies QDF2432.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing the interrupt trigger region id to 2 and the
corresponding threshold set0/set1 values to 8/16.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NToan Le <toanle@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since ethernet v1 hardware has a bug related to coalescing, disabling
this feature.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NToan Le <toanle@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today.  I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.

On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.

This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While grant reference is of type uint32_t, xen-netfront erroneously casts
it to signed short in BUG_ON().

This would lead to the xen domU panic during boot-up or migration when it
is attached with lots of paravirtual devices.
Signed-off-by: NDongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Moxa CAN devices.
Signed-off-by: NLukas Resch <l.resch@incubedit.com>
Signed-off-by: NChristoph Zehentner <c.zehentner@incubedit.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.

The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).

Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.

Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.

Fixes: 9a4d7e86 ("qede: Add support for Tx/Rx-only queues.")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions.  Symptoms include random
segfaults and silent data corruption over NFS.

The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.

So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.

Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.

This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.

Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.

Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.

In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 8d7533e5.

It introduced kbuild failures, new version coming.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.

At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP.  On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.

The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.

Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.

Fixes: f9baff50 ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.

If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.

Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.

To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.

Fixes: 55ad3592 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a0 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.

This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.

Fixes: 31c128b6 ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the default status of quality of service back to disabled,
as it hurts performance in some cases.

Fixes: 38438f7c ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.

Fixes: 27bf91d6 ("mlx4_core: Add link type autosensing")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).

Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.

Fixes: 623ed84b ("mlx4_core: initial header-file changes for SRIOV support")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard

   phy-connection-type = "rgmii-id";

On a phy node.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit e3f74b84
("hv_netvsc: report vmbus name in ethtool")'
because of problem introduced by commit f9a56e5d6a0ba
("Drivers: hv: make VMBus bus ids persistent").
This changed the format of the vmbus name and this new format is too
long to fit in the bus_info field of ethtool.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to release resources properly in error handling path of
alloc_uld_rxqs(), This patch also removes unwanted arguments
and avoids calling the same function twice.

Fixes: 94cdb8bb (cxgb4: Add support for dynamic allocation
       of resources for ULD
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an old warning about mlx4_SW2HW_EQ_wrapper on x86:

ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’:
ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

The problem here is that gcc won't track the state of the variable
across a spin_unlock. Moving the assignment out of the lock is
safe here and avoids the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the firmware can't work with a page with dma address 0.
Passing such an address to the firmware will cause the give_pages
command to fail.

To avoid this, in case we get a 0 dma address of a page from the
dma engine, we avoid passing it to FW by remapping to get an address
other than 0.

Fixes: bf0bf77f ('mlx5: Support communicating arbitrary host...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that the kernel PCI error handlers are not called, we will
trigger our own recovery flow.

The health work will give priority to the kernel pci error handlers to
recover the PCI by waiting for a small period, if the pci error handlers
are not triggered the manual recovery flow will be executed.

We don't save pci state in case of manual recovery because it will ruin the
pci configuration space and we will lose dma sync.

Fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is a race between the health care work and the kernel
pci error handlers because both of them detect the error, the first one
to be called will do the error handling.
There is a chance that health care will disable the pci after resuming
pci slot.
Also create a separate WQ because now we will have two types of health
works, one for the error detection and one for the recovery.

Fixes: 89d44f0a ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The health sick status should be cleared when we start the health poll.
This is crucial for driver reload (unload + load) in order to behave
right in case of health issue.

Fixes: fd76ee4d ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ingress/Egress ACL enable function may fail and it should return
status to its caller to avoid NULL pointer dereference.

Fixes: f942380c ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detaching the netdev before unregistering it cause some netdev cleanup
ndos to fail because they check presence of the netdev, so we need to
unregister the netdev first.

Fixes: 26e59d80 ('net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>