I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8 ("bonding: don't increase
rx_dropped after processing LACPDUs")

I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.

This inter-diffs such that the warnings are now gone.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER.  As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.

Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.

To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.

Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 7d26bb10 "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.

Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.

How to reproduce this bug ?

                       -----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24  \--|-- eth1-/                       |
                       --------------------------------

1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1

then eth0 is the active slave, and MAC of bond0 is MAC of eth0.

2 on hostA, ping 192.168.100.2

3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.

4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: NDavid Howells <dhowells@redhat.com>

The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.

        commit 917fbdb3
        Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
        Date:   Wed Nov 23 23:37:15 2011 +0000

            bonding: only use primary address for ARP

That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address.  Unfortunately, it
didn't always work as expected.

When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address.  The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten.  The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.

This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once.  The
inconsistent behavior between those two interfaces was something that
needed to be resolved.

While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver.  I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.

As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address.  This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.

I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.

Thanks to Ralf for all his help on this.

v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.

v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.

eth0--
      |-- bond0 -- br0
eth1--

modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1

brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0

Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.

The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.

If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.

Instead I choose to modify bonding to send igmp report for its master.

Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.

Remove the allocation failure messages.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC
address. This is done differently for TLB and ALB modes.
bond->alb_info.rlb_enabled is used to discriminate between the two modes but
this flag may be uninitialized if the slave is being enslaved prior to calling
bond_open() -> bond_alb_initialize() on the master.

It turns out all the callers of alb_set_slave_mac_addr() pass
bond->alb_info.rlb_enabled as the hw parameter.

This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and
makes the function decide based on the bonding mode instead, which fixes the
above problem.
Reported-by: NNarendra K <Narendra_K@Dell.com>
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to lock soft irqs under bond_alb_xmit()
which already has softirq disabled.

Changes:
1. add non-bh/bh version to tlb_clear_slave()

2. represent BH and non BH hash table locks
_lock_rx_hashtbl_bh/_unlock_rx_hashtbl_bh
_lock_rx_hashtbl/_unlock_rx_hashtbl
_lock_tx_hashtbl_bh/_unlock_tx_hashtbl_bh
_lock_tx_hashtbl/_unlock_tx_hashtbl
Signed-off-by: NMaxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.

The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves

The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.

The sysdev code will be going away soon, so this include needs to be
removed no matter what.

Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>

This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let caller know the result of adding/removing vlan id to/from vlan
filter.

In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: NHenrik Saavedra Persson <henrik.e.persson@ericsson.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@drr.davemloft.net>

This file is now unused and should have been removed by commit
7c899432 ("bonding, ipv4, ipv6, vlan:
Handle NETDEV_BONDING_FAILOVER like NETDEV_NOTIFY_PEERS").
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

C assignment can handle struct in6_addr copying.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing mode via bonding's sysfs, the slaves are not initialized
correctly. Forbid to change modes with slaves present to ensure that every
slave is initialized correctly via bond_enslave().
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Acked-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only distinct use is checking if NETIF_F_NOCACHE_COPY should be
enabled by default. The check heuristics is altered a bit here,
so it hits other people than before. The default shouldn't be
trusted for performance-critical cases anyway.

For all other uses NETIF_F_NO_CSUM is equivalent to NETIF_F_HW_CSUM.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Zheng Liang(lzheng@redhat.com) found a bug that if we config bonding with
arp monitor, sometimes bonding driver cannot get the speed and duplex from
its slaves, it will assume them to be 100Mb/sec and Full, please see
/proc/net/bonding/bond0.
But there is no such problem when uses miimon.

(Take igb for example)
I find that the reason is that after dev_open() in bond_enslave(),
bond_update_speed_duplex() will call igb_get_settings()
, but in that function,
it runs ethtool_cmd_speed_set(ecmd, -1); ecmd->duplex = -1;
because igb get an error value of status.
So even dev_open() is called, but the device is not really ready to get its
settings.

Maybe it is safe for us to call igb_get_settings() only after
this message shows up, that is "igb: p4p1 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX".

So I prefer to update the speed and duplex for a slave when reseices
NETDEV_CHANGE/NETDEV_UP event.

Changelog
V2:
1 remove the "fake 100/Full" logic in bond_update_speed_duplex(),
  set speed and duplex to -1 when it gets error value of speed and duplex.
2 delete the warning in bond_enslave() if bond_update_speed_duplex() returns
  error.
3 make bond_info_show_slave() handle bad values of speed and duplex.
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c

This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

This patch resolves two sets of race conditions.

	Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the
first, as follows:

The bond_close() calls cancel_delayed_work() to cancel delayed works.
It, however, cannot cancel works that were already queued in workqueue.
The bond_open() initializes work->data, and proccess_one_work() refers
get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when
work->data has been initialized. Thus, a panic occurs.

	He included a patch that converted the cancel_delayed_work calls
in bond_close to flush_delayed_work_sync, which eliminated the above
problem.

	His patch is incorporated, at least in principle, into this
patch.  In this patch, we use cancel_delayed_work_sync in place of
flush_delayed_work_sync, and also convert bond_uninit in addition to
bond_close.

	This conversion to _sync, however, opens new races between
bond_close and three periodically executing workqueue functions:
bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon.

	The race occurs because bond_close and bond_uninit are always
called with RTNL held, and these workqueue functions may acquire RTNL to
perform failover-related activities.  If bond_close or bond_uninit is
waiting in cancel_delayed_work_sync, deadlock occurs.

	These deadlocks are resolved by having the workqueue functions
acquire RTNL conditionally.  If the rtnl_trylock() fails, the functions
reschedule and return immediately.  For the cases that are attempting to
perform link failover, a delay of 1 is used; for the other cases, the
normal interval is used (as those activities are not as time critical).

	Additionally, the bond_mii_monitor function now stores the delay
in a variable (mimicing the structure of activebackup_arp_mon).

	Lastly, all of the above renders the kill_timers sentinel moot,
and therefore it has been removed.
Tested-by: NMitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Acked-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I made class_attr_bonding_matters per network namespace and dynamically
allocated I overlooked the need for calling sysfs_attr_init.  Oops.

This fixes the following lockdep splat:

[    5.749651] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[    5.749655] bonding: MII link monitoring set to 100 ms
[    5.749676] BUG: key f49a831c not in .data!
[    5.749677] ------------[ cut here ]------------
[    5.749752] WARNING: at kernel/lockdep.c:2897 lockdep_init_map+0x1c3/0x460()
[    5.749809] Hardware name: ProLiant BL460c G1
[    5.749862] Modules linked in: bonding(+)
[    5.749978] Pid: 3177, comm: modprobe Not tainted 3.1.0-rc9-02177-gf2d1a4e-dirty #1157
[    5.750066] Call Trace:
[    5.750120]  [<c1352c2f>] ? printk+0x18/0x21
[    5.750176]  [<c103112d>] warn_slowpath_common+0x6d/0xa0
[    5.750231]  [<c1060133>] ? lockdep_init_map+0x1c3/0x460
[    5.750287]  [<c1060133>] ? lockdep_init_map+0x1c3/0x460
[    5.750342]  [<c103117d>] warn_slowpath_null+0x1d/0x20
[    5.750398]  [<c1060133>] lockdep_init_map+0x1c3/0x460
[    5.750453]  [<c1355ddd>] ? _raw_spin_unlock+0x1d/0x20
[    5.750510]  [<c11255c8>] ? sysfs_new_dirent+0x68/0x110
[    5.750565]  [<c1124d4b>] sysfs_add_file_mode+0x8b/0xe0
[    5.750621]  [<c1124db3>] sysfs_add_file+0x13/0x20
[    5.750675]  [<c1124e7c>] sysfs_create_file+0x1c/0x20
[    5.750737]  [<c1208f09>] class_create_file+0x19/0x20
[    5.750794]  [<c12c186f>] netdev_class_create_file+0xf/0x20
[    5.750853]  [<f85deaf4>] bond_create_sysfs+0x44/0x90 [bonding]
[    5.750911]  [<f8410947>] ? bond_create_proc_dir+0x1e/0x3e [bonding]
[    5.750970]  [<f841007e>] bond_net_init+0x7e/0x87 [bonding]
[    5.751026]  [<f8410000>] ? 0xf840ffff
[    5.751080]  [<c12abc7a>] ops_init.clone.4+0xba/0x100
[    5.751135]  [<c12abdb2>] ? register_pernet_subsys+0x12/0x30
[    5.751191]  [<c12abd03>] register_pernet_operations.clone.3+0x43/0x80
[    5.751249]  [<c12abdb9>] register_pernet_subsys+0x19/0x30
[    5.751306]  [<f84108b9>] bonding_init+0x832/0x8a2 [bonding]
[    5.751363]  [<c10011f0>] do_one_initcall+0x30/0x160
[    5.751420]  [<f8410087>] ? bond_net_init+0x87/0x87 [bonding]
[    5.751477]  [<c106d5cf>] sys_init_module+0xef/0x1890
[    5.751533]  [<c1356490>] sysenter_do_call+0x12/0x36
[    5.751588] ---[ end trace 89f492d83a7f5006 ]---
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a network namespace misfeature that bonding_masters looked at
current instead of the remembering the context where in which
/sys/class/net/bonding_masters was opened in to see which network
namespace to act upon.

This removes the need for sysfs to handle tagged directories with
untagged members allowing for a conceptually simpler sysfs
implementation.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port shouldn't be enabled unless its current MUX
state is DISTRIBUTING which is correctly handled by
ad_mux_machine(), otherwise the packet sent can be
lost because the other end may not be ready.

The issue happens on every port initialization, but
as the ports are expected to move quickly to DISTRIBUTING,
it doesn't cause much problem.  However, it does cause
constant packet loss if the other peer has the port
configured to stay in STANDBY (i.e. SYNC set to OFF).
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bond->recv_probe is called in bond_handle_frame() when
a packet is received, but bond_close() sets it to NULL. So,
a panic occurs when both functions work in parallel.

Why this happen:
After null pointer check of bond->recv_probe, an sk_buff is
duplicated and bond->recv_probe is called in bond_handle_frame.
So, a panic occurs when bond_close() is called between the
check and call of bond->recv_probe.

Patch:
This patch uses a local function pointer of bond->recv_probe
in bond_handle_frame(). So, it can avoid the null pointer
dereference.
Signed-off-by: NMitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed.  I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.

There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first.  There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.

This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set.  I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Reported-by: NLiang Zheng <lzheng@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
  from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
  iboe_get_rate was previously ->get_settings() called unlocked. This
  fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
  problem. Also fixed by calling __dev_get_by_index() instead of
  dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
  so bnx2fc_if_create() and fcoe_if_create() are called locked as they
  are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

v2->v3:
	-removed dev_ethtool_get_settings()
	-added ASSERT_RTNL into __ethtool_get_settings()
	-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
	 around it and __ethtool_get_settings() call
v1->v2:
        add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benefit from use of ndo_change_rx_flags in handling change of promisc
and allmulti. No need to store previous state locally.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eduard Sinelnikov (eduard.sinelnikov@gmail.com) found that if we change
bonding mode from active backup to round robin, some slaves are still keeping
"backup", and won't transmit packets.

As Jay Vosburgh(fubar@us.ibm.com) pointed out that we can work around that by
removing the bond_is_active_slave() check, because the "backup" flag is only
meaningful for active backup mode.

But if we just simply ignore the bond_is_active_slave() check,
the transmission will work fine, but we can't maintain the correct value of
"backup" flag for each slaves, though it is meaningless for other mode than
active backup.

I'd like to reset "backup" and "inactive" flag in bond_open,
thus we can keep the correct value of them.

As for bond_is_active_slave(), I'd like to prepare another patch to handle it.

V2:
Use C style comment.
Move read_lock(&bond->curr_slave_lock).
Replace restore with reset, for active backup mode, it means "restore",
but for other modes, it means "reset".
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bonding device is created via rtnl, it is created with default number
of rx/tx queues. This patch implements callback in bonding so the
correct value (previously specified by bonding module param) is used.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>