Remove Marzen legacy board code written in C. Instead
board support expressed in DT shall be used together
with Multiplatform and shmobile_defconfig.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The STMicrolectornics's STM32F429 MCU has the following main features:
 - Cortex-M4 core running up to @180MHz
 - 2MB internal flash, 256KBytes internal RAM
 - FMC controller to connect SDRAM, NOR and NAND memories
 - SD/MMC/SDIO support
 - Ethernet controller
 - USB OTFG FS & HS controllers
 - I2C, SPI, CAN busses support
 - Several 16 & 32 bits general purpose timers
 - Serial Audio interface
 - LCD controller
Tested-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMaxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add a minimum Device Tree for Acme Arietta G25.
http://acme.systems/ariettaSigned-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NSergio Tanzilli <tanzilli@acmesystems.it>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch adds support for the imx6dl based aristainetos2 board
with following configuration:

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM:  1 GiB
NAND:  1024 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)

As this board can be used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>

add imx7d sdb board support
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add support to the Armadeus Systems APF6 Solo / Dual / Quad SoM and
the Armadeus Systems APF6Dev carrier board.

For more details see:
http://www.armadeus.com/english/products-processor_boards-apf6.html
http://www.armadeus.com/english/products-development_boards-apf6_dev.htmlSigned-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add support for the Gateworks GW5510 board featuring:
 * i.MX6 SoC
 * up to 512MB DDR3
 * up to 2GB NAND flash
 * 1x miniPCIe socket (with USB)
 * HDMI out (micro-HDMI)
 * HDMI in (micro-HDMI) (currently supported by only vendor kernel)
 * TTL level I/O (supported by GW16111 breakout board):
  * I2C
  * 2x UART
  * CAN
  * 2x DIO (GPIO/PWM)
  * USB OTG

For more details see:
 http://www.gateworks.com/product/item/ventana-gw5510-single-board-computerSigned-off-by: NTim Harvey <tharvey@gateworks.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
   2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.

This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.

Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).

This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.

This commit adds a dts file for the v1.1 pcb with an a33 soc.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The SinA33 is a core/SDK development board by Sinlinx. The core board
does not have any connectors or pads, other than the pads used to connect
it to the SDK board.

The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip,
the AXP223 PMIC, and supporting discrete components. eMMC is optional.

The SDK board has a USB host, USB OTG, volume control and home buttons,
audio input/output jacks, a micro-SD slot, camera and SDIO expansion
headers, an LCD connector, and a GPIO expansion header, which has
UARTs, MIPI DSI and I2C available. Only UART0 is enabled though.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

ET-Q8_A33 is A33 based cheap tablet in common Q8 format.

It has 512MB RAM, 4GB Nand, 7" Display, RDA5900P wifi, GSL1680 touch, etc.
Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NChen-Yu Tsai <wens@csie.org>

The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NAndy Simpkins <andy.simpkins@toby-churchill.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DNS-327L is a 2-bay NAS with the following specs:
     - 512MiB RAM
     - 128MiB NAND Flash
     - 1 GbE interface (Marvell PHY)
     - 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
     - 2 internal SATA ports handled by the Armada 370:
       	 uses 2 gpios for power control
     - two front 2-color leds (amber + white) for both discs,
        controlled by the SoC
     - One white LED handled by SoC (USB)
     - 3 buttons. Power handled by weltrend, USB and
       RESET (on the bottom) are wired via GPIOs
     - Unidentified i2c device at address 0x13 (via i2cdetect)
     - UART0 providing serial console
     - Weltrend MCU serving for RTC, temperature, fan control,
       and power button handling interfaced via UART1
       (Handled via userspace dns320l-daemon)
Signed-off-by: NAndrew Andrianov <andrew@ncrmnt.org>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).

Both boards have:

- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM

gregory.clement@free-electrons.com: use serial0:115200n8 in
stdout-path and remove the bootargs part in the chosen node
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This device is an industrial PC based on
AM335x SoC.

[ balbi@ti.com : updated to fit current mainline ]
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.

Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.

Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.

Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The i.MX27 dtb build should be controlled by CONFIG_SOC_IMX27 rather
than CONFIG_SOC_IMX31.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Fixes: cb612390 ("ARM: dts: Only build dtb if associated Arch and/or SoC is enabled")
Cc: <stable@vger.kernel.org>

Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.

More information can be found on:
http://www.hitex.com/index.php?id=3212Signed-off-by: NAriel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.

More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.phpSigned-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Initial device trees for UniPhier SoCs: PH1-sLD3, PH1-LD4, PH1-Pro4,
and PH1-sLD8.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.

Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

With reworked device tree files for Compulab CM-A510 SoM and SBC-A510
base board, now add the correspoding board file to Makefile again.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Prior reworking Dove based Compulab CM-A510 device tree, remove it
from the compiled device tree files.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add DT file for Kizbox 2 board.
This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
Signed-off-by: NGaël PORTAY <g.portay@overkiz.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add DT file for Kizbox mini board.
This board is based on Atmel's AT91SAM9G25 SoC.
Signed-off-by: NGaël PORTAY <g.portay@overkiz.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Rename to match AT91 naming convention.
Signed-off-by: NGaël PORTAY <g.portay@overkiz.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash,
a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles,
a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV.

This patch adds basic support for the device, more information can be found
here (http://linux-sunxi.org/MK808C).
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Jesurun Q5 has a black plastic casing with the approximate dimensions
of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it
features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The
external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female
jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the
device has 1x red LED (hard wired to power) and an programmable green led.
On the board there is also an unpopulated IR receiver and the UART.
The devices is equipped with an AXP209 PMU.

For more details see: http://linux-sunxi.org/Jesurun_Q5Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orangepi mini is a development board using the Allwinner A20 SoC,
with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI,
1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports,
ir receiver and a headphones jack.

Also see:
http://linux-sunxi.org/Xunlong_Orange_Pi_Mini
http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM,
microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A
ports, ir receiver and a headphones jack.

Also see:
http://linux-sunxi.org/Xunlong_Orange_Pi
http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.

[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdfSigned-off-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>