Some old example code has been left lying around. Remove the example
code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Once in a time omapdss had basic support for fifomerge. Fifomerge was
removed as the implementation didn't work properly, and a proper
implementation is a complex problem.

However, some unused fifo-merge related code was left behind. This patch
removes those.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc_mgr_is_enabled() was missing a prototype in dss.h
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

ULPS cannot be entered if the DDR clk is enabled. Thus disable the DDR
clk before entering ULPS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We sometimes get timeout when disabling the DSI interface with video
mode. It looks like the disable will stall until the current frame has
been finished, and this can take multiple milliseconds.

wait_for_bit_change() currently uses a busyloop to wait for a bit to
change. This is used in multiple places. The problem is, we don't have
clear understanding how long particular operations can take, so the
function needs to support longer waits.

Improve wait_for_bit_change() to first busy loop for 100 times to see if
the bit changes almost right away. If the bit hasn't changed, move to a
loop with a sleep of 1ms, and poll for 500ms.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current code always enters ULPS for 3 lanes. This is not right, as
there could be only 2 lanes used, and on OMAP4 we have 5 lanes.

Fix the code to put all used lanes into ULPS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There's no longer need for the dsi_get_num_lanes_used function, so it
can be removed. The lane check in dsi_init_display() can be removed as
the validity of the config will be verified when parsing it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_enable_lane_override(). The function
parameters are also slightly changed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_wait_tx_clk_esc_reset(). This also
extends the function to support 5 lanes on OMAP4, instead of 3 lanes.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_get_lane_mask().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_set_lane_config().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Parse the lane configuration from the device data into internal lane
config format. This will be used in the following patches to clean up
the lane handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI driver currently counts used lanes and number of supported lanes by
using the number of data lanes (i.e. excluding clock lane). This patch
changes this to use the number of all lanes so that the following lane
config patches are cleaner.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Flush posted write in _enable_lcd_out() and _enable_digit_out(). This
ensures the the lcd/digit bit is written before the code starts waiting
for interrupts about enabling/disabling the output.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Flush posted write after setting the bit to send the BTA to ensure the
BTA is sent right away, as the code in dsi_vc_send_bta_sync() waits for
an interrupt caused indirectly by sending the BTA.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Flush posted write between writing the ULPS enable bits and waiting for
the interrupt.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add data for the FocalTech ETM070003DH6 display to the generic_dpi_panel
display driver.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Commit f2c31e32 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.

Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: NMarc Aurele La France <tsi@ualberta.ca>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This following can occur with ipoib when processing a multicast reponse:

    BUG: soft lockup - CPU#0 stuck for 67s! [ib_mad1:982]
    Modules linked in: ...
    CPU 0:
    Modules linked in: ...
    Pid: 982, comm: ib_mad1 Not tainted 2.6.32-131.0.15.el6.x86_64 #1 ProLiant DL160 G5
    RIP: 0010:[<ffffffff814ddb27>]  [<ffffffff814ddb27>] _spin_unlock_irqrestore+0x17/0x20
    RSP: 0018:ffff8802119ed860  EFLAGS: 00000246
    0000000000000004 RBX: ffff8802119ed860 RCX: 000000000000a299
    RDX: ffff88021086c700 RSI: 0000000000000246 RDI: 0000000000000246
    RBP: ffffffff8100bc8e R08: ffff880210ac229c R09: 0000000000000000
    R10: ffff88021278aab8 R11: 0000000000000000 R12: ffff8802119ed860
    R13: ffffffff8100be6e R14: 0000000000000001 R15: 0000000000000003
    FS:  0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
    CR2: 00000000006d4840 CR3: 0000000209aa5000 CR4: 00000000000406f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Call Trace:
    [<ffffffffa032c247>] ? ipoib_mcast_send+0x157/0x480 [ib_ipoib]
    [<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
    [<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
    [<ffffffffa03283d4>] ? ipoib_path_lookup+0x124/0x2d0 [ib_ipoib]
    [<ffffffffa03286fc>] ? ipoib_start_xmit+0x17c/0x430 [ib_ipoib]
    [<ffffffff8141e758>] ? dev_hard_start_xmit+0x2c8/0x3f0
    [<ffffffff81439d0a>] ? sch_direct_xmit+0x15a/0x1c0
    [<ffffffff81423098>] ? dev_queue_xmit+0x388/0x4d0
    [<ffffffffa032d6b7>] ? ipoib_mcast_join_finish+0x2c7/0x510 [ib_ipoib]
    [<ffffffffa032dab8>] ? ipoib_mcast_sendonly_join_complete+0x1b8/0x1f0 [ib_ipoib]
    [<ffffffffa02a0946>] ? mcast_work_handler+0x1a6/0x710 [ib_sa]
    [<ffffffffa015f01e>] ? ib_send_mad+0xfe/0x3c0 [ib_mad]
    [<ffffffffa00f6c93>] ? ib_get_cached_lmc+0xa3/0xb0 [ib_core]
    [<ffffffffa02a0f9b>] ? join_handler+0xeb/0x200 [ib_sa]
    [<ffffffffa029e4fc>] ? ib_sa_mcmember_rec_callback+0x5c/0xa0 [ib_sa]
    [<ffffffffa029e79c>] ? recv_handler+0x3c/0x70 [ib_sa]
    [<ffffffffa01603a4>] ? ib_mad_completion_handler+0x844/0x9d0 [ib_mad]
    [<ffffffffa015fb60>] ? ib_mad_completion_handler+0x0/0x9d0 [ib_mad]
    [<ffffffff81088830>] ? worker_thread+0x170/0x2a0
    [<ffffffff8108e160>] ? autoremove_wake_function+0x0/0x40
    [<ffffffff810886c0>] ? worker_thread+0x0/0x2a0
    [<ffffffff8108ddf6>] ? kthread+0x96/0xa0
    [<ffffffff8100c1ca>] ? child_rip+0xa/0x20

Coinciding with stack trace is the following message:

    ib0: ib_address_create failed

The code below in ipoib_mcast_join_finish() will note the above
failure in the address handle but otherwise continue:

                ah = ipoib_create_ah(dev, priv->pd, &av);
                if (!ah) {
                        ipoib_warn(priv, "ib_address_create failed\n");
                } else {

The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():

        if (!mcast->ah) {
                if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
                        skb_queue_tail(&mcast->pkt_queue, skb);
                else {
                        ++dev->stats.tx_dropped;
                        dev_kfree_skb_any(skb);
                }

My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.

There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.

The test that induced the failure is associated with a host SM on the
same server during a shutdown.

This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets.  Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Reviewed-by: NGary Leshner <gary.leshner@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

With the revert of "of/irq: of_irq_find_parent: check for parent equal to
child" (dc937280), we need another way to handle parent node equal
to the child node. This can simply be handled in of_irq_init by checking
for this condition.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Tested-by: NPawel Moll <pawel.moll@arm.com>
Tested-by: NStephen Warren <swarren@nvidia.com>

In the case where CONFIG_PSTORE=n, the function efi_pstore_read() doesn't
have the correct list of parameters. This patch provides a definition
of efi_pstore_read() with 'char **buf' added to fix this warning:
"drivers/firmware/efivars.c:609: warning: initialization from".

problem introduced in commit f6f82851Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Don't over-schedule QSFP work on driver initialization.  It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads.  In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix logic so that we don't retry with MPAv1 once we have done that
already.  Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID.  This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.

Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function.  'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.

[Edited commit message for legibility -- broonie]
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8 ("ath9k_hw: Add support for AR946/8x chipsets") that
caused a nasty regression to appear on my Acer Ferrari One (the box
locks up entirely at random times after the wireless has been started
without any way to get debug information out of it).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900"
adds subname parameter for mfp_set_groupg.

Thus add subname parameter to the callers.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NWan Zongshun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix build failure in staging iio driver:

.../drivers/staging/iio/industrialio-core.c: In function 'iio_event_getfd':
.../drivers/staging/iio/industrialio-core.c:262:32: error:
			'ev_int' undeclared (first use in this function)

Also convert the rest of the function to use the new variable.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch converts the drivers in drivers/hwmon/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Simon Guinot <sguinot@lacie.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_register_driver(),
so we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.

Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.

This conflicts with how drivers use reset, which is typically:
	reset
	unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.

Fix by flushing out the write, and flushing pending interrupts.

This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Guest features selector spelling mistake.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Fix this compile error on s390:

  CC [M]  drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'

Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning

drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

The wrong bits were put on the wire, fix that.

This fixes kernel bug #42562.
Signed-off-by: NSheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>