CONFIG_OF_MDIO is tristate and will be m if PHYLIB is m.  Use
IS_ENABLED macro to prevent build error:

 ERROR: "of_mdio_find_bus" [drivers/net/phy/mdio-mux.ko] undefined!
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Included changes:

* fix a little bug in the DHCP packet snooping introduced so far
* minor fixes and cleanups
* minor routing protocol API cleanups
* add a new contributor name to translation-table.{c,h}
* update copyright years in file headers
* minor improvement for the routing algorithm

translation_table.{c,h} have been heavily modified by another contributor and
for legal purposes it is better to include his name into the contributor list
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

update copyright years in order to include 2012
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Regression introduced by: f76d019194e0a88c57371df169ecc979690a04c2
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

batman-adv would forward OGMs from non-besthops while replacing the the TQ
and TTL values with the values from the best hop. In certain corner cases
this leads to a temporary routing loop.
This patch changes this behavior: Only packets from best next hops are
forwarded - TQ and TTL values won't be replaced anymore. However, the protocol
needs to rebroadcast OGMs from single hop neighbors regardless of whether or
not they are the best hop. To handle this case a new flag is introduced to
alert neighboring nodes about the forwarded OGM that is not from my best
next hop. It is to be discarded by all nodes except for the one originating
the OGM.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NDaniele Furlan <daniele.furlan@gmail.com>
Tested-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>

This allows us to easily add a sysfs parameter for an unsigned int
later, which is not for a batman mesh interface (e.g. bat0), but for a
common interface instead. It allows reading and writing an atomic_t in
hard_iface (instead of bat_priv compared to the mesh variant).

Developed by Linus during a 6 months trainee study period in Ascom
(Switzerland) AG.
Signed-off-by: NLinus Luessing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Reported-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The B.A.T.M.A.N. IV OGM receive function still was hard-coded although
it is a routing protocol specific function. This patch takes advantage
of the dynamic packet handler registration to remove the hard-coded
function calls.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The packet handler array replaces the growing switch statement, thus
dealing with incoming packets in a more efficient way. It also adds
to possibility to register packet handlers on the fly.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

In is_type_dhcprequest(), while parsing a DHCP message, if the entry we found in
the option list is neither a padding nor the dhcp-type, we have to ignore it and
jump as many bytes as its length + 1. The "+ 1" byte is given by the subtype
field itself that has to be jumped too.
Reported-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

According to the RFC4944 (Transmission of IPv6 Packets over
IEEE 802.15.4 Networks), chapter 7:

The IPv6 link-local address [RFC4291] for an IEEE 802.15.4 interface
is formed by appending the Interface Identifier, as defined above, to
the prefix FE80::/64.

  10 bits            54 bits                  64 bits
+----------+-----------------------+----------------------------+
|1111111010|         (zeros)       |    Interface Identifier    |
+----------+-----------------------+----------------------------+

This patch adds IPv6 address generation support for the 6lowpan
interfaces.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An implementation of CoDel AQM, from Kathleen Nichols and Van Jacobson.

http://queue.acm.org/detail.cfm?id=2209336

This AQM main input is no longer queue size in bytes or packets, but the
delay packets stay in (FIFO) queue.

As we don't have infinite memory, we still can drop packets in enqueue()
in case of massive load, but mean of CoDel is to drop packets in
dequeue(), using a control law based on two simple parameters :

target : target sojourn time (default 5ms)
interval : width of moving time window (default 100ms)

Based on initial work from Dave Taht.

Refactored to help future codel inclusion as a plugin for other linux
qdisc (FQ_CODEL, ...), like RED.

include/net/codel.h contains codel algorithm as close as possible than
Kathleen reference.

net/sched/sch_codel.c contains the linux qdisc specific glue.

Separate structures permit a memory efficient implementation of fq_codel
(to be sent as a separate work) : Each flow has its own struct
codel_vars.

timestamps are taken at enqueue() time with 1024 ns precision, allowing
a range of 2199 seconds in queue, and 100Gb links support. iproute2 uses
usec as base unit.

Selected packets are dropped, unless ECN is enabled and packets can get
ECN mark instead.

Tested from 2Mb to 10Gb speeds with no particular problems, on ixgbe and
tg3 drivers (BQL enabled).

Usage: tc qdisc ... codel [ limit PACKETS ] [ target TIME ]
                          [ interval TIME ] [ ecn ]

qdisc codel 10: parent 1:1 limit 2000p target 3.0ms interval 60.0ms ecn
 Sent 13347099587 bytes 8815805 pkt (dropped 0, overlimits 0 requeues 0)
 rate 202365Kbit 16708pps backlog 113550b 75p requeues 0
  count 116 lastcount 98 ldelay 4.3ms dropping drop_next 816us
  maxpacket 1514 ecn_mark 84399 drop_overlimit 0

CoDel must be seen as a base module, and should be used keeping in mind
there is still a FIFO queue. So a typical setup will probably need a
hierarchy of several qdiscs and packet classifiers to be able to meet
whatever constraints a user might have.

One possible example would be to use fq_codel, which combines Fair
Queueing and CoDel, in replacement of sfq / sfq_red.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Class bytes/packets stats can be misleading because they are updated in
enqueue() while packet might be dropped later.

We already fixed all qdiscs but sch_atm.

This patch makes the final cleanup.

class rate estimators can now match qdisc ones.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.

Done via cocci script:

$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
-	!compare_ether_addr_64bits(a, b)
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	compare_ether_addr_64bits(a, b)
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal_64bits(a, b) == 0
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal_64bits(a, b) != 0
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	ether_addr_equal_64bits(a, b) == 0
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	ether_addr_equal_64bits(a, b) != 0
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal_64bits(a, b)
+	ether_addr_equal_64bits(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an optimized boolean function to check if
2 ethernet addresses are the same.

This is to avoid any confusion about compare_ether_addr_64bits
returning an unsigned, and not being able to use the
compare_ether_addr_64bits function for sorting ala memcmp.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling pci_disable_sriov() while VFs are assigned to VMs causes
kernel panic. This patch uses PCI_DEV_FLAGS_ASSIGNED bit state of the
VF's pci_dev to avoid this. Also, the unconditional function reset cmd
issued on a PF probe can delete the VF configuration for the
previously enabled VFs. A scratchpad register is now used to issue a
function reset only when needed (i.e., in a crash dump scenario.)
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If enabled, L2TP data packets have sequence numbers which a receiver
can use to drop out of sequence frames or try to reorder them. The
first frame has sequence number 0, but the L2TP code currently expects
it to be 1. This results in the first data frame being handled as out
of sequence.

This one-line patch fixes the problem.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When L2TP data packet reordering is enabled, packets are held in a
queue while waiting for out-of-sequence packets. If a packet gets
lost, packets will be held until the reorder timeout expires, when we
are supposed to then advance to the sequence number of the next packet
but we don't currently do so. As a result, the data channel is stuck
because we are waiting for a packet that will never arrive - all
packets age out and none are passed.

The fix is to add a flag to the session context, which is set when the
reorder timeout expires and tells the receive code to reset the next
expected sequence number to that of the next packet in the queue.

Tested in a production L2TP network with Starent and Nortel L2TP gear.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As proposed by Eric, make the tcp_input.o thinner.

add/remove: 1/1 grow/shrink: 1/4 up/down: 868/-1329 (-461)
function                                     old     new   delta
tcp_try_rmem_schedule                          -     864    +864
tcp_ack                                     4811    4815      +4
tcp_validate_incoming                        817     815      -2
tcp_collapse                                 860     858      -2
tcp_send_rcvq                                555     353    -202
tcp_data_queue                              3435    3033    -402
tcp_prune_queue                              721       -    -721
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noted by Eric, no checks are performed on the data size we're
putting in the read queue during repair. Thus, validate the given
data size with the common rmem management routine.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It actually works on the input queue and will use its read mem
routines, thus it's better to have in in the tcp_input.c file.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version number to better match the version of the out of tree
driver with similar functionality.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the hwmon code was initially added it was with the assumption that a
sysfs patch would be also coming soon.  Since that isn't the case some
clean up needs to be done.  This patch does that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the MAC, in order to provide the best software
timestamps. This patch adds this call for that support.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the ethtool get_ts_info operation, which enables
access of available timestamp/timesync support for that device. It can query
which ptp clock device is associated with the particular port.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current value of the udelay timeout for ixgbe_disable_rx_buff is too
short. This causes the security path to not not be properly disabled during
the section that is meant to have it turned off. The end result causes a race
condition that results in RX issues.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.

The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.

This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.

Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.

Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the VF sends a MACVLAN request with index of zero then it is not
actually trying to add a filter.  Check the index value and only
indicate that operation is not allowed when the VF is actually trying
to add a filter.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present.  This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work.  By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the logic in the priority based flow control
configuration routines.  Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.

In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>