Bump.

Change-ID: Ifa19aadaa892ad103f1b96fe2361fa690912c6a3
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we reset a VF, its VSI goes away, and it gets a new one. So don't
hang on to the now-stale local VSI pointer. It just leads to suffering
and kernel panics.

Change-ID: Ia8823b4e85893e95e963acee284968022b29177a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to suspend scheduling or any pending service task during driver
unload process, so that new task will not be scheduled. This patch sets
the suspend flag bit during reload which avoids service task execution.

Change-ID: I017c57b5d6656564556e3c5387da671369a572ac
Signed-off-by: NPandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.

We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive.  We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.

Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.

Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new opcodes and struct used for asking the firmware to update Rx
control registers that need extra care when being accessed while under
heavy traffic - e.g. sustained 64byte packets at line rate on all ports.
The firmware will take extra steps to be sure the register accesses
are successful.

The registers involved are:
	PFQF_CTL_0
	PFQF_HENA
	PFQF_FDALLOC
	PFQF_HREGION
	PFLAN_QALLOC
	VPQF_CTL
	VFQF_HENA
	VFQF_HREGION
	VSIQF_CTL
	VSILAN_QBASE
	VSILAN_QTABLE
	VSIQF_TCREGION
	PFQF_HKEY
	VFQF_HKEY
	PRTQF_CTL_0
	GLFCOE_RCTL
	GLFCOE_RSOF
	GLQF_CTL
	GLQF_SWAP
	GLQF_HASH_MSK
	GLQF_HASH_INSET
	GLQF_HSYM
	GLQF_FC_MSK
	GLQF_FC_INSET
	GLQF_FD_MSK
	PRTQF_FD_INSET
	PRTQF_FD_FLXINSET
	PRTQF_FD_MSK

Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return from i40e_vsi_reinit_setup() if vsi param is NULL.
This makes this code consistent with all the other code that
checks for NULL before using one of the VSI pointers accessed
with an indexed variable. (Indexed VSI pointers are
intentionally set to NULL in i40e_vsi_clear() and
i40e_remove().

Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985
Signed-off-by: NJohn Underwood <johnx.underwood@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.

Change-ID: I31e76673125275f3c69a14c646361919d04dc987
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes an issue where a previously removed message
has returned.  Changing the message type to dev_dbg
leaves the info, if desired, but takes it out of normal
everyday usage. Also changed call to only provide port
data when its valid and not when its not (delete case).

Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just like Tx queues don't wait for Rx queues to be disabled before
DCB has been reconfigured.
Check the queues are disabled only after the DCB configuration has
been applied to the VSI(s) managed by the PF driver.

In case of any timeout issue a PF reset to recover.

Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When linking with particular PHY types (ex: copper PHY), the amount of
time it takes for the GLGEN_RSTAT_DEVSTATE to be set increases greatly,
which can lead to a timeout and failure to load the driver.

Change-ID: If02be0dfcd7c57fdde2d5c81cd63651260cd2029
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's.  Without this
patch, the blink led functionality fails on some parts.  This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.

Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions to blink led on devices using
10GBaseT PHY since MAC registers used in other designs
do not work in this device configuration.

Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On all of the other Intel drivers we place checksum close to TSO as they
have a significant amount in common and it can help to reduce the decision
tree for how to handle the frame as the first check in TSO is to see if
checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx
checksum offload based on a single check.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.

The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path.  Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.

The logic for the scan is fairly simple.  If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment.  This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.

Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives.  However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame.  For this reason I am splitting up
the descriptor count function from the function that stops the ring.

Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit e5d3a51c ("bnx2x: extend DCBx support") was missing HSI
changes for big-endian machine, breaking compilation on such
platforms.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the code for determining the L4 protocol and L3 header
length so that when IPv6 extension headers are being used we can determine
the offset and type of the L4 protocol.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums.  As such we can update the
feature flags to reflect that.

In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.

I also found one spot where we were setting the same flag twice.  It looks
like it was probably a git merge error that resulted in the line being
duplicated.  As such I have dropped it in this patch.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums.  As such we can update the
feature flags to reflect that.

In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All of the documentation in the datasheets for the XL710 do not call out
any reason to exclude support for IPv6 based tunnels.  As such I am
dropping the code that was excluding these tunnel types from having their
port numbers recognized.  This way we can take advantage of things such as
checksum offload for inner headers over IPv6 based VXLAN or GENEVE
tunnels.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch contains a number of fixes to make certain that we are using
the correct protocols when parsing both the inner and outer headers of a
frame that is mixed between IPv4 and IPv6 for inner and outer.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NKiran Patil <kiran.patil@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The XL722 has support for providing the outer UDP tunnel checksum on
transmits.  Make use of this feature to support segmenting UDP tunnels with
outer checksums enabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is mostly a minor clean-up for the Rx checksum path in order to avoid
some of the unnecessary conditional checks that were being applied.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Device would start receiving only vlan-tagged traffic with tags matching
that of one of the configured vlan IDs, unless:
  - Device is expliicly placed in PROMISC mode.
  - Device exhausts its vlan filter credits.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today, interfaces are working in vlan-promisc mode; But once
vlan filtering offloaded would be supported, we'll need a method to
control it directly [e.g., when setting device to PROMISC, or when
running out of vlan credits].

This adds the necessary API for L2 client to manually choose whether to
accept all vlans or only those for which filters were configured.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add exception handling to the Tx checksum path so that we can handle cases
of TSO where the frame is bad, or Tx checksum where we didn't recognize a
protocol

Drop I40E_TX_FLAGS_CSUM as it is unused, move the CHECKSUM_PARTIAL check
into the function itself so that we can decrease indent.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch defers writing to the Tx descriptor bits until we know we have
successfully completed a given operation.  So for example we defer updating
the tunnelling portion of the context descriptor until we have fully
identified the type.

The advantage to this approach is that we can assemble values as we go
instead of having to try and kludge everything together all at once.  As a
result we can significantly clean up the tunneling configuration for
instance as we can just do a pointer walk and do the math for the distance
between each set of points.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for IPv6 extension headers in setting up the Tx
checksum.  Without this patch extension headers would cause IPv6 traffic to
fail as the transport protocol could not be identified.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two issues.  First was the fact that iphdr(skb)->protocl
was being used to test for the outer transport protocol.  This completely
breaks IPv6 support.  Second was the fact that we cleared the flag for v4
going to v6, but we didn't take care of txflags going the other way.  As
such we would have the v6 flag still set even if the inner header was v4.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx checksum path was maintaining a set of 3 pointers and two lengths in
order to prepare the packet for being checksummed.  The thing is we only
really needed 2 pointers, and the lengths that were being maintained can
easily be computed.

As such we can replace the IPv4 and IPv6 header pointers with one single
union that represents both, or a generic pointer to the start of the
network header.  For the L4 headers we can do the same with TCP and a
generic pointer to the start of the transport header.  The length of the
TCP header is obtained by simply multiplying doff by 4, and the network
header length can be obtained by subtracting the network header pointer
from the transport header pointer.

While I was at it I renamed l4_hdr to l4_proto to make it a bit more clear
and less likely to be confused with l4.hdr which is the transport header
pointer.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch goes through and pulls all of the spots where we were updating
either the TCP or IP checksums in the TSO and checksum path into the TSO
function.  The general idea here is that we should only be updating the
header after we verify we have completed a skb_cow_head check to verify the
head is writable.

One other advantage to doing this is that it makes things much more
obvious.  For example, in the case of IPv6 there was one spot where the
offset of the IPv4 header checksum was being updated which is obviously
incorrect.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that the L4 header offsets and such can be ignored
when dealing with the L3 checksum and length update.  This is done making
use of two things.

First we can just use the offset from the L4 header to the start of the
packet to determine the L4 offset, and from that we can then make use of
the data offset to determine the full length of the headers.

As far as adjusting the checksum to remove the length we can simply add the
inverse of the length instead of having to recompute the entire
pseudo-header without the length.  In the case of an IPv6 header this
should be significantly cheaper since we can make use of a value we already
needed instead of having to read the source and destination address out of
the packet.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of casing u32 values to u64 it makes more sense to just start out
with u64 values in the first place.  This way we don't need to create a
mess with all of the casts needed to populate a 64b value.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels.  The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.

In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.

Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.

As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: Ie280dc67e37a1cf667c3469499a4fb90f4177b75
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In MFP mode particularly when we were setting the PF VSI in limited
promiscuous, the HW switch was still mirroring the outgoing packets
from other VSIs (VF/VMdq) onto the PF VSI.

With this new bit set, the mirroring doesn't happen any more and so
we are in limited promiscuous on the PF VSI in MFP which is similar
to defport.

An API check is not required, since this bit is reserved for FW API
version < 1.5

Also update copyright year in file headers.

Change-ID: I9840cb95f11dde733d943cb03ce84f68b9611bc8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In one obscure corner case, it was possible to clear the NVM update wait
flag when no update_done message was actually received.  This patch
cleans the event descriptor before use, and moves the opcode check to
where it won't get done if there was no event to clean.

Also update copyright year in file headers.

Change-ID: I68bbc41965e93f4adf07cbe98b9dfd63d41509a4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>