Microoptimization:
This reduces the udelay in bcm43xx_mac_suspend.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Suspend MAC (and make MAC-suspend refcounting) when doing
long periodic work.
On long periodic work, we disable IRQs on the device, so
we don't want the MAC to stay operating and probably miss
packets due do non-delivery of interrupts.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add WE-19 capabilities to prism54 fullmac driver so that it supports the
necessary Wireless Extensions WPA calls.  Convert reporting of WPA/RSN
Generic Information Elements to IWEVGENIE rather than pre-WE-19
IWEVCUSTOM as well.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wireless.h discourages using SIOCGIWNAME to publish the driver name
which the interface belongs to. Use SIOCGIWNICKN instead.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ipw2200 uses // comments, and uses them for removing unneeded
code. Clean it up a bit.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When determining whether there's a key to set or not, orinoco should be
looking at the key length, not the key data.  Otherwise confusion reigns
when trying to set TX key only, passing in zero-length key, but non-NULL
pointer.  Key length takes precedence over non-NULL key data.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked
it down to a problem with the new shared key auth code (recursive
calls into the driver)

This patch (effectively Michael's patch with a couple of small
modifications) solves the problem by sending the authentication
challenge response frame from a workqueue entry.

I also removed a lone \n from the bcm43xx messages relating to
authentication mode - this small change was previously discussed but
not patched in.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver airo (for Cisco Wlan-Cards) complains about "failed to load
transform for AES", when it is loaded and CRYPTO_AES is not selected
in Kconfig.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

zd1201 has nasty tendency to emit magicall anti-wifi cloud when it is
inserted into slot, but not used.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes three drivers to compile again after my patch that removes
the data_cmnd member from struct scsi_cmnd.

The fas216 change is trivial, it should have been using ->cmnd all the
time.

NCR53C9 (which seem to be mostly duplicate driver with esp.c!) is doing
something odd, it should only have looked at ->cmnd before not the saved
copy that is kept for the error handlers sake.  Note that it really
should deal with the sync setting themselves but use the generic domain
validation code that get this right - but that's for later let's push
this simple compile fix for now.

And sorry for the late fix for this, I have been busy with OLS and
associated activities last week.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.

The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
   __cpufreq_driver_target
   __cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
   __cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
   lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
   __cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
   the lock_cpu_hotplug() lock.

I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.

The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)

The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update version to 3.63.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.

Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.

Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to postpone the queue startup until after the softirq
handler has actually finished some requests, otherwise we could
be racing with cciss_softirq_done() and not actually restart
the queue handling.
Signed-off-by: NJens Axboe <axboe@suse.de>

The data_cmd[] member got deleted, so do not use it any more.  Scsi
commands do not have their ->cmd[] overwritten temporary to probe for
status after an error before retrying.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The neighbour ha field may get updated without destroying the
neighbour.  In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Need to set mcast->ah before debug code dereferences it.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port).  Without this, RMPP transactions get aborted because
of duplicate packets.

This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver.  In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address.  It also returns the correct page size
for FMRs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Lockdep warns because uverbs is trying to take uobj->mutex when it
already holds that lock.  This is because there are really multiple
types of uobjs even though all of their locks are initialized in
common code.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ib_uverbs_create_ah() and ib_uverbs_create_srq() did not release the
PD's read lock in their error paths, which lead to deadlock when
destroying the PD.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Shutting down the ondemand policy was fraught with potential
problems, causing issues for SMP suspend (which wants to hot-
unplug) all but the last CPU.

This should fix at least the worst problems (divide-by-zero
and infinite wait for the workqueue to shut down).
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It before entering in the loop for freeing the other ifb devices.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes pci_module_init() to pci_register_driver().
Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WAN: Converted synclink drivers to use netif_carrier_*() instead
of hdlc_set_carrier().
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WAN: Cosmetic changes to N2 and C101 drivers
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WAN: Fixed a problem with PPP/raw HDLC/X.25 protocols not doing
netif_dormant_off() at startup.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just do a linear enumeration so that we handle sun4d systems
correctly.  As a consequence, eliminate the hard coded keyboard and
mouse channel line values, use the CONS_{KEYB,MS} flags instead.

Also, report the keyboard/mouse Zilog channels just like the uart ones
do.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>