Indicate whether this is a Generation-I (50xx), Generation-II (60xx),
or Generation-II-E (6042/7042) chip.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.

Note that pata_it8213 mask differed from the comment.  Added a FIXME there.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for the SATA portion of Marvell's AHCI-compatible chips.
The PATA port capability, also available via AHCI, is disabled until
support is completed.

NCQ and PCI MSI are disabled by default.  Marvell says "we use NCQ" in
their drivers but "we do not use PCI MSI."  Theoretically that implies
we need to fix ahci.c to work with Marvell NCQ, but one wonders why
Marvell NCQ is any different from other AHCI chips.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Use ATA_UDMA*
* Remove FIXME notations that once served to remind us to verify
  that these were indeed the correct UDMA masks.  They are.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add ata_dumb_qc_prep and supporting logic so that a driver can just
specify it needs to be helped in this area. 64K entries are split
as with drivers/ide.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sil24_interrupt() loads host->ports[i] into a local variable,
validates it, and then loads the value again in the call to
sil24_host_intr(). This patch replaces the second load by a
reference to the local variable.

This is safe since no side-effects have occurred since the
initial load. It also improves readability since it makes
it clear that the parameter to sil24_host_intr() is the same
value which was just validated.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On some embedded platforms, such as blackfin, the gpio interrupt for
IDE interface is designed to be triggered with high voltage. The gpio
port should be configured properly by set_irq_type() when register
the irq. This patch enable the generic pata platform driver to
accept platform irq flags data.
Signed-off-by: NSonic Zhang <sonic.adi@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch applies some trivial cleanups to sata_promise:
- repair whitespace damage
- correct comment at board_2057x_pata definition
- pull SATAII TX4 support code out to separate functions
- rename ata_nr to ata_no for consistency with libata's port_no
- remove some init-time debug printks (requested by Jeff)

This patch should cause no behavioural changes, except for
the removed printks.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
--
 drivers/ata/sata_promise.c |   56 ++++++++++++++++++---------------------------
 1 files changed, 23 insertions(+), 33 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reported by Michael-Luke Jones.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix various bugs in pio/mwdma mode programming.

* Control bits in the timing register wasn't cleared properly while
  programming PIO mode.

* MWDMA mode programming cleared the wrong part of control bits.

* MWDMA mode programming cleared udma_mask even when the controller
  doesn't support UDMA.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Minor cleanups, in preparation for merging Marvell PATA AHCI support in
the future.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sata_sx4:
- describe overall driver theory of operation
- add a few constants that will be used in the future

sata_via:
- remove mention of an old-EH function that is going away
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Function renaming and factorization.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge unrelated cleanups (__devinit, dev_dbg, hardware constant)
from changeset "pata_sil680: Add MMIO support" authored by
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* convert tabs to spaces
* convert some hex numbers to (1 << n) preferred format
* document i2c and timer control register bits
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make it easier to verify which struct initializers are present, by
presenting them in the order in which they are defined in the API
header.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH.  Remove.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make the register offset table more maintainable.

From the 'sii-lbt' branch, which enables the LBT chip feature.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ahci: enable sg segment clustering

The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ap->cbl == ATA_CBL_SATA indicates SATA cable while ap->flags &
ATA_FLAG_SATA indicates SATA host port.  Till now they always gave the
same result but SATA/PATA bridge handling will change that.  Switch to
ATA_FLAG_SATA test if we're testing for host port type.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From AMD.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement _GTM/_STM support.  acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle.  A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend.  _STM is executed in ata_acpi_on_resume().  With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.

ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation.  ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove remaining unnecessary feature and status checks.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used.  These two
functions are responsible for determining whether specific ACPI method
is used and when.

On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag.  This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).

On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF.  _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies.  As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.

If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure.  If it fails again on the second try, ACPI is disabled
on the device.  Note that successful configuration clears ACPI failed
status.

With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume().  As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Add missing LOCKING: and RETURNS: to function comment.

* Don't conditionalize warning messages with ata_msg_probe().  Print
  directly with KERN_WARNING.

* Drop duplicate debug messages.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch cleans up ata_acpi_exec_tfs() and its friends.

* Rename taskfile_array to ata_acpi_gtf and make it __packed as it's
  used as argument to ACPI method, and use pointer to ata_acpi_gtf and
  number of taskfiles to represent _GTF taskfiles instead of a pointer
  casted into unsigned long and byte count.  This makes argument
  re-checking in do_drive_set_taskfiles() unnecessary.

* Pointer in void * not in unsigned long.

* Clean up do_drive_get_GTF() error handling and make
  do_drive_get_GTF() return number of taskfiles on success, 0 if _GTF
  doesn't exist or doesn't contain valid ata.  -errno on other errors.

* Remove superflous check for acpi->buffer.pointer.

* Update taskfile_load_raw() such that printed messages look similar
  to the messages printed by ata_eh_report().

* s/do_drive_get_GTF/ata_dev_get_GTF/
  s/do_drive_set_taskfiles/ata_dev_set_taskfiles/
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Add acpi_handle to ata_host and ata_port.  Rename
  ata_device->obj_handle to ->acpi_handle and move it above such that
  it doesn't get cleared on reconfiguration.

* Replace ACPI node association which ata_acpi_associate() which is
  called once during host initialization.  Unlike the previous
  implementation, ata_acpi_associate() uses ATA_FLAG_ACPI_SATA to
  choose between IDE or SATA ACPI hierarchy and uses simple child look
  up instead of recursive walk to match the nodes.  This is way safer
  and simpler.  Please read the following message for more info.

  http://article.gmane.org/gmane.linux.ide/17554Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

PCMCIA doesn't use DMA and as this driver is used on many platforms we
don't want it to fail on those that define the DMA alloc API as a NULL
return
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We got it backwards and now the other detects are fixed it shows up
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mirrors change in IT821X
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch was found to fix some of the problems with the
pata_ali driver.

https://bugzilla.redhat.com/bugzilla/attachment.cgi?id=156482Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NFlorian Attenberger  <valdyn@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work.  Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.

The port info printing in ata_host_register() doesn't fit all the
different controllers.  It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Only the ADMA entry was supposed to be able to change queue depth.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Changed PATA handler for PATA-ports used by sata_sis.
This patch was originally submitted by Jeff Garzik.

Added PCI-ID 1180 for SiS966 Controller in pata_sis.
The 1180 mode is fully compatible to other SiS PATA-controller.

The PCI-ID 1183 is SATA in PATA-emulation, but not fully compatible
to SiS5513/5518. sata_sis.c is forwarding this ID to pata_sis.
1183 is not working if simply added to pata_sis.
This handling fixes issues with SiS968.
Signed-off-by: NUwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Another member of HTS5416* family doing spurious NCQ completion.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Enrico Sardi <enricoss@tiscali.it>
Signed-off-by: NJeff Garzik <jeff@garzik.org>