Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 14 1月, 2006 6 次提交
    • D
      [PATCH] spi: add spi_driver to SPI framework · b885244e
      由 David Brownell 提交于 
      This is a refresh of the "Simple SPI Framework" found in 2.6.15-rc3-mm1
which makes the following changes:

  * There's now a "struct spi_driver".  This increase the footprint
    of the core a bit, since it now includes code to do what the driver
    core was previously handling directly.  Documentation and comments
    were updated to match.

  * spi_alloc_master() now does class_device_initialize(), so it can
    at least be refcounted before spi_register_master().  To match,
    spi_register_master() switched over to class_device_add().

  * States explicitly that after transfer errors, spi_devices will be
    deselected.  We want fault recovery procedures to work the same
    for all controller drivers.

  * Minor tweaks:  controller_data no longer points to readonly data;
    prevent some potential cast-from-null bugs with container_of calls;
    clarifies some existing kerneldoc,

And a few small cleanups.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      b885244e
    • D
      [PATCH] spi: mtd dataflash driver · 1d6432fe
      由 David Brownell 提交于 
      This is a conversion of the AT91rm9200 DataFlash MTD driver to use the
lightweight SPI framework, and no longer be AT91-specific.  It compiles
down to less than 3KBytes on ARM.

The driver allows board-specific init code to provide platform_data with
the relevant MTD partitioning information, and hotplugs.

This version has been lightly tested.  Its parent at91_dataflash driver has
been pretty well banged on, although kernel.org JFFS2 dataflash support was
acting broken the last time I tried it.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      1d6432fe
    • D
      [PATCH] spi: ads7846 driver · ffa458c1
      由 David Brownell 提交于 
      This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers.  Key differences from those two:

  - Uses the new SPI framework (minimalist version)
  - <linux/spi/ads7846.h> abstracts board-specific touchscreen info
  - Sysfs attributes for the temperature and voltage sensors
  - Uses fewer ARM-specific IRQ primitives

The temperature and voltage sensors show up in sysfs like this:

  $ pwd
  /sys/devices/platform/omap-uwire/spi2.0
  $ ls
  bus@          input:event0@ power/        temp1         vbatt
  driver@       modalias      temp0         vaux
  $ cat modalias
  ads7846
  $ cat temp0
  991
  $ cat temp1
  1177
  $

So far only basic testing has been done.  There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.

One portability note may be of special interest.  It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response".  Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention.  So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      ffa458c1
    • D
      [PATCH] spi: simple SPI framework · 8ae12a0d
      由 David Brownell 提交于 
      This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).

  - It's still less than 2KB of ".text" (ARM).  If there's got to be a
    mid-layer for something so simple, that's the right size budget.  :)

  - The guts use board-specific SPI device tables to build the driver
    model tree.  (Hardware probing is rarely an option.)

  - This version of Kconfig includes no drivers.  At this writing there
    are two known master controller drivers (PXA/SSP, OMAP MicroWire)
    and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
    mentions of other drivers in development.

  - No userspace API.  There are several implementations to compare.
    Implement them like any other driver, and bind them with sysfs.

The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:

  - One bugfix (removes a FIXME), with the visible effect of making device
    names be "spiB.C" where B is the bus number and C is the chipselect.

  - The "caller provides DMA mappings" mechanism now has kerneldoc, for
    DMA drivers that want to be fancy.

  - Hey, the framework init can be subsys_init.  Even though board init
    logic fires earlier, at arch_init ... since the framework init is
    for driver support, and the board init support uses static init.

  - Various additional spec/doc clarifications based on discussions
    with other folk.  It adds a brief "thank you" at the end, for folk
    who've helped nudge this framework into existence.

As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.

From: Mark Underwood <basicmark@yahoo.com>

  Update the SPI framework to remove a potential priority inversion case by
  reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      8ae12a0d
    • P
      [PATCH] Increase AT_VECTOR_SIZE · 67daf5f1
      由 Paul Mackerras 提交于 
      On PowerPC, we want to be able to provide an AT_PLATFORM aux table
entry to userspace, so that glibc can choose optimized libraries for
the processor we're running on.  Unfortunately that would be the 21st
aux table entry on powerpc, meaning that the aux table including the
terminating null entry would overflow the mm->saved_auxv[] array,
leading to userland programs segfaulting.

This increases the size of the mm->saved_auxv array to be large enough
to accommodate an AT_PLATFORM entry on powerpc.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      67daf5f1
    • E
      [PATCH] Fix oops in ufs_fill_super at mount time · 8a430d74
      由 Evgeniy 提交于 
      There's a lack of parenthesis in fs/ufs/utils.h, so instead of the 512th
byte of buffer, the usb2 pointer will point to the nth structure of type
ufs_super_block_second.

This can cause a mount-time oops if you're unlucky (especially with
DEBUG_PAGEALLOC, which is how Alexey Dobriyan saw this problem)
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Acked-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      8a430d74
  3. 13 1月, 2006 34 次提交