* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Remove a bad BUG_ON in the fence management code.

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: ignore EDID with really tiny modes.
  drm: don't associate _DRM_DRIVER maps with a master
  drm/i915: intel_lvds.c fix section mismatch
  drm: Hook up DPMS property handling in drm_crtc.c. Add drm_helper_connector_dpms.
  drm: set permissions on edid file to 0444
  drm: add newlines to text sysfs files
  drm/radeon: fix ring free alignment calculations
  drm: fix irq naming for kms drivers.

While running 20 parallel instances of dd as follows:

  #!/bin/bash
  for i in `seq 1 20`; do
           dd if=/dev/zero of=/export/hda3/dd_$i bs=1073741824 count=1 &
  done
  wait

on a 16G machine, we noticed that rather than just killing the processes,
the entire kernel went down.  Stracing dd reveals that it first does an
mmap2, which makes 1GB worth of zero page mappings.  Then it performs a
read on those pages from /dev/zero, and finally it performs a write.

The machine died during the reads.  Looking at the code, it was noticed
that /dev/zero's read operation had been changed by
557ed1fa ("remove ZERO_PAGE") from giving
zero page mappings to actually zeroing the page.

The zeroing of the pages causes physical pages to be allocated to the
process.  But, when the process exhausts all the memory that it can, the
kernel cannot kill it, as it is still in the kernel mode allocating more
memory.  Consequently, the kernel eventually crashes.

To fix this, I propose that when a fatal signal is pending during
/dev/zero read operation, we simply return and let the user process die.
Signed-off-by: NSalman Qazi <sqazi@google.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
[ Modified error return and comment trivially.  - Linus]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We don't set up the canary; let's disable stack protector on boot.c so
we can get into lguest_init, then set it up.  As a side effect,
switch_to_new_gdt() sets up %fs for us properly too.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This could be triggered by a gtt mapping fault on 965 that decides to
remove the fence from another object that happens to be active currently.
Since the other object doesn't rely on the fence reg for its execution, we
don't wait for it to finish.  We'll soon be not waiting on 915 most of the
time as well, so just drop the BUG_ON.
Signed-off-by: NEric Anholt <eric@anholt.net>

Some EDIDs lie and report tiny modes that aren't possible. Ignore
these modes.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A driver will use the _DRM_DRIVER map flag to indicate that it wants
to be responsible for removing the map itself, bypassing the DRM's
automagic cleanup code.

Since the multi-master changes this has been broken, resulting in some
drivers having their registers unmapped before it's finished with them.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

intel_no_lvds[] does not require __initdata as it is used only by

void intel_lvds_init(struct drm_device *dev).
Signed-off-by: NJaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.

That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.

This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Without initializing the sysfs attributes for the edid file,
it was created with mode 0, making it difficult for applications to use.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The contents of various simple text files in sysfs should end with
a newline to make them easier to read from the console.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

fd.o bz#21849

We were aligning to +16 dwords, instead of to the next 16dword
boundary in the ring. Fix the calculation to go to the next 16dword
boundary when space checking.
Signed-off-by: NDave Airlie <airlied@redhat.com>

allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.

So this is the cleaner version that just picks devname or driver name
in the irq code.

It removes the devname allocs from the i915 driver.
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pmac: Update PowerMac 32-bit defconfig

Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.

This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...

Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd

In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup
  e1000: add missing length check to e1000 receive routine
  forcedeth: add phy_power_down parameter, leave phy powered up by default (v2)
  Bluetooth: Remove useless flush_work() causing lockdep warnings

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: prevent deadlock in xfs_qm_shake()
  xfs: fix overflow in xfs_growfs_data_private
  xfs: fix double unlock in xfs_swap_extents()

net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup

This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.

When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained.  After it's chained,
tc_ctl_tfilter() calls classifier's change().  When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.

In addition, cls_cgroup is initialized in change() not in init().  It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: NMinoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Tested-by: NMinoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	Patch to fix bad length checking in e1000.  E1000 by default does two
things:

1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put

Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set.  This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test).  If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb.  This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU.  The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000.  This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Tested-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.

The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072).  Leaving the phy
powered on is the safest default behavior.  Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: NEd Swierk <eswierk@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's possible to recurse into filesystem from the memory
allocation, which deadlocks in xfs_qm_shake(). Add check
for __GFP_FS, and bail out if it is not set.
Signed-off-by: NFelix Blyakher <felixb@sgi.com>
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NFelix Blyakher <felixb@sgi.com>

In the case where growing a filesystem would leave the last AG
too small, the fixup code has an overflow in the calculation
of the new size with one fewer ag, because "nagcount" is a 32
bit number.  If the new filesystem has > 2^32 blocks in it
this causes a problem resulting in an EINVAL return from growfs:

 # xfs_io -f -c "truncate 19998630180864" fsfile
 # mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile
 # mount -o loop fsfile /mnt
 # xfs_growfs /mnt

meta-data=/dev/loop0             isize=256    agcount=52,
agsize=76288719 blks
         =                       sectsz=512   attr=2
data     =                       bsize=4096   blocks=3905982455, imaxpct=5
         =                       sunit=0      swidth=0 blks
naming   =version 2              bsize=4096   ascii-ci=0
log      =internal               bsize=4096   blocks=32768, version=2
         =                       sectsz=512   sunit=0 blks, lazy-count=0
realtime =none                   extsz=4096   blocks=0, rtextents=0
xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument

Reported-by: richard.ems@cape-horn-eng.com
Signed-off-by: NEric Sandeen <sandeen@sandeen.net>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NFelix Blyakher <felixb@sgi.com>
Signed-off-by: NFelix Blyakher <felixb@sgi.com>

Regreesion from commit ef8f7fc5, which rearranged the code in
xfs_swap_extents() leading to double unlock of xfs inode ilock.
That resulted in xfs_fsr deadlocking itself on platforms, which
don't handle double unlock of rw_semaphore nicely. It caused the
count go negative, which represents the write holder, without
really having one. ia64 is one of the platforms where deadlock
was easily reproduced and the fix was tested.
Signed-off-by: NEric Sandeen <sandeen@sandeen.net>
Reviewed-by: NEric Sandeen <sandeen@sandeen.net>
Signed-off-by: NFelix Blyakher <felixb@sgi.com>

This mostly adds back AppleTouch support and adds CONFIG_HIGHMEM
by default.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: hash - Fix handling of sg entry that crosses page boundary

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Update documentation on fan_max
  hwmon: (lm78) Add missing __devexit_p()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix section attribute warnings.
  sparc64: Fix SET_PERSONALITY to not clip bits outside of PER_MASK.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  3c509: Add missing EISA IDs
  MAINTAINERS: take maintainership of the cpmac Ethernet driver
  net/firmare: Ignore .cis files
  ath1e: add new device id for asus hardware
  mlx4_en: Fix a kernel panic when waking tx queue
  rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle
  at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan
  mac8390: fix build with NET_POLL_CONTROLLER
  cxgb3: link fault fixes
  cxgb3: fix dma mapping regression
  netfilter: nfnetlink_log: fix wrong skbuff size	calculation
  netfilter: xt_hashlimit does a wrong SEQ_SKIP
  bfin_mac: fix build error due to net_device_ops convert
  atlx: move modinfo data from atlx.h to atl1.c
  gianfar: fix babbling rx error event bug
  cls_cgroup: read classid atomically in classifier
  netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache
  netfilter: nf_ct_tcp: fix accepting invalid RST segments

* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
  headers_check fix: linux/net_dropmon.h
  headers_check fix: linux/auto_fs.h

Add fan_max description.

Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: NChristian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Several EISA device IDs for 3c509 family network cards are missing from 
the driver, making the cards unusable in their EISA mode.  Here's a fix to 
add them based on the EISA configuration files distributed by 3Com and our 
eisa.ids database.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds me as the maintainer of the CPMAC (AR7)
Ethernet driver.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix the following 'make headers_check' warnings:

  usr/include/linux/net_dropmon.h:7: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

fix the following 'make headers_check' warnings:

  usr/include/linux/auto_fs.h:17: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

A quirk that we've always supported is having an sg entry that's
bigger than a page, or more generally an sg entry that crosses
page boundaries.  Even though it would be better to explicitly have
to sg entries for this, we need to support it for the existing users,
in particular, IPsec.

The new ahash sg walking code did try to handle this, but there was
a bug where we didn't increment the page so kept on walking on the
first page over an dover again.

This patch fixes it.
Tested-by: NMartin Willi <martin@strongswan.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide_pci_generic: add quirk for Netcell ATA RAID