Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Improve code style by removing the unnecessary else block of an if
statement which immediately returns.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the ether_addr_copy function instead of copying byte-by-byte in a
for-loop by hand.
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2015-12-12

This series contains updates to e1000, e1000e and igb.

Joern Engel fixes up the e1000 driver to reduce scheduler latencies by
making the eeprom read/write functions scheduler friendly by using a mutex
lock instead of a spin lock.

Todd adds code for igb to initialize the 88E1543 PHY properly.  Then fixed
igb to use the correct i210 register for EEMNGCTL, since the i210 has two
EEPROM access registers (EEARBC and EEMNGCTL).

Dmitry Vyukov provides a fix for e1000 to resolve a data race found with
KernelThreadSanitizer (KTSAN), where no memory barriers were being used
when buffers get recycled, so the recycled buffers can be corrupted.  So
use smp_store_release() to update tx_ring->next_to_clean and
smp_load_acquire() to read tx_ring->next_to_clean to properly hand off
buffers from e1000_clean_tx_irq() to e1000_xmit_frame().

Jarod Wilson fixes igb so that we do not try to unmap a NULL hw_addr.  Then
cleaned up array_rd32() so that it uses igb_rd32() the same as rd32() and
use io_addr() in more places so that we do not have to call E1000_REMOVED().

Janusz Wolak cleans up the e1000 driver by correcting warnings produced
by checkpatch.pl for the driver.

Jean Sacren provides several patches with general cleanups for e1000 and
e1000e, which include code comment fix-ups and cleanup of local variables
not needed.

Dmitry Fleytman fixes a possible division by zero in the receive interrupt
handler for e1000e when working without adaptive interrupt moderation,
which is typically disabled on jumbo MTUs.

Raanan increases the timeout of the polling bit due to timing changes to
the ME firmware on a platform, so increase the timeout to 300ms.  Added
initial support for i219-LM, which is a LOM that will be available on
systems with the Lewisburg Platform Controller HUB (PCH) chipset.

Jan Beulich fixes a NULL dereference in igb, due to the adapter->vf _data
being NULL while adapter->vfs_allocated_count is non-zero.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2015-12-12

This series contains updates to i40e and i40evf only.

Jesse fixes some trivial static analyzer warnings where BIT() can be used
instead of BIT_ULL().

Mitch fixes the virtual channel interface which was using incorrect semantics
to remove MAC addresses and would leave incorrect filters active when using
VLANs.  Also fixes an issue that when VF's are created, the MAC address
defaults to all zeros, indicating to the VF driver that it should use a
random MAC address.  However, the PF driver was incorrectly adding this
zero MAC to the filter table, so check for a good address before adding
the default filter.  Adds a check to make sure that the Tx and Rx rings
actually exist before dereferencing them to free resources.  Re-classifies
several messages which are really for debugging purposes, especially since
the driver can fully recover from any of these.  Fixed up the VF version
strings to match the PF driver.

Anjali adds a virtchnl offload to support the expanded version of TCP/UDP
PCTYPES for RSS.

Shannon fixes i40e to clean the whole MAC filter list when resetting after
an intermediate add or delete push to the firmware.

v2: added blank line after variable declaration in patch 9 based on
    feedback from Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The combined effect of commits 6423fc34 ("igb: do not re-init SR-IOV
during probe") and ceee3450 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.

The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: NDmitry Fleytman <dmitry@daynix.com>
Signed-off-by: NLeonid Bloch <leonid@daynix.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJanusz Wolak <januszvdm@gmail.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By using goto statement, we can achieve sharing the same exit path so
that code duplication could be minimized.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to historical reason, 'phy_data' has never been included in the
kernel doc. Fix it so that the requirement could be fulfilled.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use 'That' to replace 'The' so that the comment would make sense.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The checking logic needed some clean-up work, so we rewrite it by
checking for break first. With that change in place, we can even move
the second check for goto statement outside of the loop.

As this is merely a cleanup, no functional change is involved. The
questionable 'tmp != 0xFF' is intentionally left alone.

Mark Rustad and Alexander Duyck contributed to this patch.

CC: Mark Rustad <mark.d.rustad@intel.com>
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: NRoman Hodek <roman.aud@siemens.com>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJanusz Wolak <januszvdm@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I've got a startech thunderbolt dock someone loaned me, which among other
things, has the following device in it:

08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)

This hotplugs just fine (kernel 4.2.0 plus a patch or two here):

[  863.020315] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.18-k
[  863.020316] igb: Copyright (c) 2007-2014 Intel Corporation.
[  863.028657] igb 0000:08:00.0: enabling device (0000 -> 0002)
[  863.062089] igb 0000:08:00.0: added PHC on eth0
[  863.062090] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection
[  863.062091] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) e8:ea:6a:00:1b:2a
[  863.062194] igb 0000:08:00.0: eth0: PBA No: 000200-000
[  863.062196] igb 0000:08:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[  863.064889] igb 0000:08:00.0 enp8s0: renamed from eth0

But disconnecting it is another story:

[ 1002.807932] igb 0000:08:00.0: removed PHC on enp8s0
[ 1002.807944] igb 0000:08:00.0 enp8s0: PCIe link lost, device now detached
[ 1003.341141] ------------[ cut here ]------------
[ 1003.341148] WARNING: CPU: 0 PID: 199 at lib/iomap.c:43 bad_io_access+0x38/0x40()
[ 1003.341149] Bad IO access at port 0x0 ()
[ 1003.342767] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi igb dca firewire_ohci firewire_core crc_itu_t rfcomm ctr ccm arc4 iwlmvm mac80211 fuse xt_CHECKSUM ipt_MASQUERADE
nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat
nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat
nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter bnep dm_mirror dm_region_hash dm_log dm_mod coretemp x86_pkg_temp_thermal intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg
[ 1003.342793]  ansi_cprng aesni_intel hp_wmi aes_x86_64 iTCO_wdt lrw iTCO_vendor_support ppdev gf128mul sparse_keymap glue_helper ablk_helper cryptd snd_hda_codec_realtek snd_hda_codec_generic
microcode snd_hda_intel uvcvideo iwlwifi snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hda_core videobuf2_core snd_hwdep btusb v4l2_common btrtl snd_seq btbcm btintel videodev cfg80211
snd_seq_device rtsx_pci_ms bluetooth pcspkr input_leds i2c_i801 media parport_pc memstick rfkill sg lpc_ich snd_pcm 8250_fintek parport joydev snd_timer snd soundcore hp_accel ie31200_edac
mei_me lis3lv02d edac_core input_polldev mei hp_wireless shpchp tpm_infineon sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables autofs4 xfs libcrc32c sd_mod sr_mod cdrom
rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci
[ 1003.342822]  nouveau ahci libahci mxm_wmi e1000e xhci_pci hwmon ptp drm_kms_helper pps_core xhci_hcd ttm wmi video ipv6
[ 1003.342839] CPU: 0 PID: 199 Comm: kworker/0:2 Not tainted 4.2.0-2.el7_UNSUPPORTED.x86_64 #1
[ 1003.342840] Hardware name: Hewlett-Packard HP ZBook 15 G2/2253, BIOS M70 Ver. 01.07 02/26/2015
[ 1003.342843] Workqueue: pciehp-3 pciehp_power_thread
[ 1003.342844]  ffffffff81a90655 ffff8804866d3b48 ffffffff8164763a 0000000000000000
[ 1003.342846]  ffff8804866d3b98 ffff8804866d3b88 ffffffff8107134a ffff8804866d3b88
[ 1003.342847]  ffff880486f46000 ffff88046c8a8000 ffff880486f46840 ffff88046c8a8098
[ 1003.342848] Call Trace:
[ 1003.342852]  [<ffffffff8164763a>] dump_stack+0x45/0x57
[ 1003.342855]  [<ffffffff8107134a>] warn_slowpath_common+0x8a/0xc0
[ 1003.342857]  [<ffffffff810713c6>] warn_slowpath_fmt+0x46/0x50
[ 1003.342859]  [<ffffffff8133719e>] ? pci_disable_msix+0x3e/0x50
[ 1003.342860]  [<ffffffff812f6328>] bad_io_access+0x38/0x40
[ 1003.342861]  [<ffffffff812f6567>] pci_iounmap+0x27/0x40
[ 1003.342865]  [<ffffffffa0b728d7>] igb_remove+0xc7/0x160 [igb]
[ 1003.342867]  [<ffffffff8132189f>] pci_device_remove+0x3f/0xc0
[ 1003.342869]  [<ffffffff81433426>] __device_release_driver+0x96/0x130
[ 1003.342870]  [<ffffffff814334e3>] device_release_driver+0x23/0x30
[ 1003.342871]  [<ffffffff8131b404>] pci_stop_bus_device+0x94/0xa0
[ 1003.342872]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342873]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342874]  [<ffffffff8131b516>] pci_stop_and_remove_bus_device+0x16/0x30
[ 1003.342876]  [<ffffffff81333f5b>] pciehp_unconfigure_device+0x9b/0x180
[ 1003.342877]  [<ffffffff81333a73>] pciehp_disable_slot+0x43/0xb0
[ 1003.342878]  [<ffffffff81333b6d>] pciehp_power_thread+0x8d/0xb0
[ 1003.342885]  [<ffffffff810881b2>] process_one_work+0x152/0x3d0
[ 1003.342886]  [<ffffffff8108854a>] worker_thread+0x11a/0x460
[ 1003.342887]  [<ffffffff81088430>] ? process_one_work+0x3d0/0x3d0
[ 1003.342890]  [<ffffffff8108ddd9>] kthread+0xc9/0xe0
[ 1003.342891]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342893]  [<ffffffff8164e29f>] ret_from_fork+0x3f/0x70
[ 1003.342894]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342895] ---[ end trace 65a77e06d5aa9358 ]---

Upon looking at the igb driver, I see that igb_rd32() attempted to read from
hw_addr and failed, so it set hw->hw_addr to NULL and spit out the message
in the log output above, "PCIe link lost, device now detached".

Well, now that hw_addr is NULL, the attempt to call pci_iounmap is obviously
not going to go well. As suggested by Mark Rustad, do something similar to
what ixgbe does, and save a copy of hw_addr as adapter->io_addr, so we can
still call pci_iounmap on it on teardown. Additionally, for consistency,
make the pci_iomap call assignment directly to io_addr, so map and unmap
match.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean,
then e1000_xmit_frame reuses the cleaned buffers. But there are no
memory barriers when buffers gets recycled, so the recycled buffers
can be corrupted.

Use smp_store_release to update tx_ring->next_to_clean and
smp_load_acquire to read tx_ring->next_to_clean to properly
hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame.

The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: NDmitry Vyukov <dvyukov@google.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Initialize the 88E1543 PHY.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Code was responsible for ~150ms scheduler latencies.
Signed-off-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NSpencer Baugh <sbaugh@catern.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: I2b8976bde070244de144e2ed8990b083de39f332
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Generate version strings like the PF driver does. This gives us more
flexibility to add suffixes to the version string at build time.

Change-ID: I0a5ca0783dd8fb849516bfc1e37ea070127847bd
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware.  The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly.  This now cleans the whole list rather
that just part of the first element.

Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.

Without this patch with X722 devices, driver will set wrong PCTYPES
for VF and UDP flows will not fan out.

Change-ID: I04fe4988253b7cd108c9179a643c969764efcb76
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.

Since these messages are really for debugging purposes, reclassify
them as such.

Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.

Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Current implementation generates compilation warnings.

Change-ID: Icceefb50fe62aefaf90a64afb7192e08355a4ec5
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.

Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.

Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.

Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.

Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.

Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.

Tested with objdump of binary before and after, no changes to code.

Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2015-12-12

This series contains updates to ixgbe only.

Alex Duyck provides almost off of the changes in this series.  First, add a
check to make sure mac_table was actually allocated and is not NULL to
ensure we do not get a NULL pointer dereference further down the line.
Fixed SR-IOV VLAN pool configuration since the code for checking the PF bit
in ixgbe_set_vf_vlan_msg() was using the wrong offset.  Cleanup/simplify
the logic for setting the VFTA register by removing the number of
conditional checks needed.  Fixed a number of issues within the VLVF and
VLFB configuration by simplifying the code.  Added support for bypassing
the VLVF entry creation when the PF is adding a new VLAN.  Reduced the
complexity of the search function used for finding a VLVF entry associated
with a given VLAN ID.  Added support for VLAN promiscuous with SR-IOV
enabled by setting all the bits in the VFTA and all of the VLVF bits
associated with teh pool belonging to the PF, in addition to cleaning up
those same bits in the event of promiscuous mode being disabled.  Fixed
and issue where we ran the risk of leaking an address into pool 0 which
really belongs to VF 0 when SR-IOV is enabled.

Emil fixes an issue with some X550 devices which can connect at 2.5Gbps,
but only with certain link partners during fail-over, so to avoid
confusion, we do not report it as supported.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for renaming and hard links to the fs. Most of this can be
implemented by using simple library operations under the same constraints
that we don't use a reserved name like elsewhere. Linking can be useful
to share/manage things like maps across subsystem users. It works within
the file system boundary, but is not allowed for directories.

Symbolic links are explicitly not implemented here, as it can be better
done already by doing bind mounts inside bpf fs to set up shared directories
f.e. useful when using volumes in docker containers that map a private
working directory into /sys/fs/bpf/ which contains itself a bind mounted
path from the host's /sys/fs/bpf/ mount that is shared among multiple
containers. For single maps instead of whole directory, hard links can
be easily used to do the same.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some X550 devices can connect at 2.5Gbps during fail-over, but only
with certain link partners. Also setting the advertised speed will
not work so we do not report it as supported to avoid confusion.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to.  What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.

Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface.  Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry.  What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>