Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 14 9月, 2012 1 次提交
    • Z
      dmaengine: mmp-pdma support · c8acd6aa
      由 Zhangfei Gao 提交于 
      1. virtual channel vs. physical channel
Virtual channel is managed by dmaengine
Physical channel handling resource, such as irq
Physical channel is alloced dynamically as descending priority,
freed immediately when irq done.
The availble highest priority physically channel will alwayes be alloced

Issue pending list -> alloc highest dma physically channel available -> dma done -> free physically channel

2. list: running list & pending list
submit: desc list -> pending list
issue_pending_list: if (IDLE) pending list -> running list; free pending list (RUN)
irq: free running list (IDLE)
     check pendlist -> pending list -> running list; free pending list (RUN)

3. irq:
Each list generate one irq, calling callback
One list may contain several desc chain, in such case, make sure only the last desc list generate irq.

4. async
Submit will add desc chain to pending list, which can be multi-called
If multi desc chain is submitted, only the last desc would generate irq -> call back
If IDLE, issue_pending_list start pending_list, transforming pendlist to running list
If RUN, irq will start pending list

5. test
5.1 pxa3xx_nand on pxa910
5.2 insmod dmatest.ko (threads_per_chan=y)
By default drivers/dma/dmatest.c test every channel and test memcpy with 1 threads per channel
Signed-off-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>
      c8acd6aa
  3. 01 9月, 2012 1 次提交
  5. 31 7月, 2012 1 次提交
  7. 13 7月, 2012 1 次提交
  9. 01 7月, 2012 1 次提交
  11. 20 6月, 2012 1 次提交
  13. 08 6月, 2012 1 次提交
  15. 07 3月, 2012 1 次提交
    • R
      DMA: sa11x0: add SA-11x0 DMA driver · 6365bead
      由 Russell King 提交于 
      Add support for the SA-11x0 DMA driver, which replaces the private
API version in arch/arm/mach-sa1100/dma.c.

We model this as a set of virtual DMA channels, one for each request
signal, and assign the virtual DMA channel to a physical DMA channel
when there is work to be done.  This allows DMA users to claim their
channels, and hold them while not in use, without affecting the
availability of the physical channels.

Another advantage over this approach, compared to the private version,
is that a channel can be reconfigured on the fly without having to
release and re-request it - which for the IrDA driver, allows us to
use DMA for SIR mode transmit without eating up three physical
channels.  As IrDA is half-duplex, we actually only need one physical
channel, and this architecture allows us to achieve that.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      6365bead
  17. 18 11月, 2011 1 次提交
  19. 09 6月, 2011 1 次提交
  21. 06 6月, 2011 1 次提交
  23. 17 3月, 2011 1 次提交
  25. 02 3月, 2011 1 次提交
    • S
      dmaengine: mxs-dma: add dma support for i.MX23/28 · a580b8c5
      由 Shawn Guo 提交于 
      This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.

* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
  instances.

* apbh-dma is different between mx23 and mx28, hardware version
  register is used to differentiate.

* mxs-dma supports pio function besides data transfer.  The driver
  uses dma_data_direction DMA_NONE to identify the pio mode, and
  steals sgl and sg_len to get pio words and numbers from clients.

* mxs dmaengine has some very specific features, like sense function
  and the special NAND support (nand_lock, nand_wait4ready).  These
  are too specific to implemented in generic dmaengine driver.

* The driver refers to imx-sdma and only a single descriptor is
  statically assigned to each channel.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
      a580b8c5
  27. 03 12月, 2010 1 次提交
  29. 08 10月, 2010 1 次提交
  31. 06 10月, 2010 1 次提交
    • S
      dmaengine: Add Freescale i.MX SDMA support · 1ec1e82f
      由 Sascha Hauer 提交于 
      This patch adds support for the Freescale i.MX SDMA engine.

The SDMA engine is a scatter/gather DMA engine which is implemented
as a seperate coprocessor. SDMA needs its own firmware which is
requested using the standard request_firmware mechanism. The firmware
has different entry points for each peripheral type, so drivers
have to pass the peripheral type to the DMA engine which in turn
picks the correct firmware entry point from a table contained in
the firmware image itself.
The original Freescale code also supports support for transfering
data to the internal SRAM which needs different entry points to
the firmware. Support for this is currently not implemented. Also,
support for the ASRC (asymmetric sample rate converter) is skipped.

I took a very simple approach to implement dmaengine support. Only
a single descriptor is statically assigned to a each channel. This
means that transfers can't be queued up but only a single transfer
is in progress. This simplifies implementation a lot and is sufficient
for the usual device/memory transfers.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NLinus Walleij <linus.ml.walleij@gmail.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      1ec1e82f
  33. 30 9月, 2010 1 次提交
    • L
      dmaengine: driver for the ARM PL080/PL081 PrimeCells v5 · e8689e63
      由 Linus Walleij 提交于 
      This creates a DMAengine driver for the ARM PL080/PL081 PrimeCells
based on the implementation earlier submitted by Peter Pearse.
This is working like a charm for memcpy and slave DMA to the PL011
PrimeCell on the PB11MPCore.

This DMA controller is used in mostly unmodified form in the ARM
RealView and Versatile platforms, in the ST-Ericsson Nomadik, and
in the ST SPEAr platform.

It has been converted to use the header from the Samsung PL080
derivate instead of its own defintions. The Samsungs have a custom
driver in their mach-* folders though, atleast we can share the
register definitions.

Cc: Peter Pearse <peter.pearse@arm.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
[GFP_KERNEL to GFP_NOWAIT in pl08x_prep_dma_memcpy]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      e8689e63
  35. 05 8月, 2010 1 次提交
  37. 28 7月, 2010 1 次提交
    • V
      intel_mid: Add Mrst & Mfld DMA Drivers · b3c567e4
      由 Vinod Koul 提交于 
      This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom

This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.

This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs

This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion

Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      b3c567e4
  39. 24 5月, 2010 1 次提交
  41. 15 4月, 2010 1 次提交
  43. 26 3月, 2010 1 次提交
  45. 02 3月, 2010 2 次提交
  47. 12 12月, 2009 1 次提交
  49. 20 11月, 2009 1 次提交
  51. 09 9月, 2009 1 次提交
  53. 29 7月, 2009 1 次提交
  55. 23 7月, 2009 1 次提交
  57. 17 6月, 2009 1 次提交
  59. 20 1月, 2009 1 次提交
    • G
      i.MX31: Image Processing Unit DMA and IRQ drivers · 5296b56d
      由 Guennadi Liakhovetski 提交于 
      i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.

IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      5296b56d
  61. 09 7月, 2008 3 次提交
    • H
      dmaengine: Driver for the Synopsys DesignWare DMA controller · 3bfb1d20
      由 Haavard Skinnemoen 提交于 
      This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.

This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.

The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.

Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:

http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf

The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682


Changes since v4:
  * Use client_count instead of dma_chan_is_in_use()
  * Add missing include
  * Unmap buffers unless client told us not to

Changes since v3:
  * Update to latest DMA engine and DMA slave APIs
  * Embed the hw descriptor into the sw descriptor
  * Clean up and update MODULE_DESCRIPTION, copyright date, etc.

Changes since v2:
  * Dequeue all pending transfers in terminate_all()
  * Rename dw_dmac.h -> dw_dmac_regs.h
  * Define and use controller-specific dma_slave data
  * Fix up a few outdated comments
  * Define hardware registers as structs (doesn't generate better
    code, unfortunately, but it looks nicer.)
  * Get number of channels from platform_data instead of hardcoding it
    based on CONFIG_WHATEVER_CPU.
  * Give slave clients exclusive access to the channel

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      3bfb1d20
    • H
      dmatest: Simple DMA memcpy test client · 4a776f0a
      由 Haavard Skinnemoen 提交于 
      This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.

The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.

Changes since v2:
  * Support testing multiple channels at the same time
  * Support testing with multiple threads competing for the same channel
  * Use counting test patterns in order to catch byte ordering issues

Changes since v1:
  * Remove extra dashes around "help"
  * Remove "default n" from Kconfig
  * Turn TEST_BUF_SIZE into a module parameter
  * Return DMA_NAK instead of DMA_DUP
  * Print unhandled events
  * Support testing specific channels and devices
  * Move to the end of the Makefile
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      4a776f0a
    • S
      dmaengine: DMA engine driver for Marvell XOR engine · ff7b0479
      由 Saeed Bishara 提交于 
      The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.

This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset

The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module.  In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.

When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      ff7b0479
  63. 05 3月, 2008 1 次提交
  65. 17 10月, 2007 3 次提交
  67. 13 7月, 2007 1 次提交
    • D
      dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines · c2110923
      由 Dan Williams 提交于 
      The Intel(R) IOP series of i/o processors integrate an Xscale core with
raid acceleration engines.  The capabilities per platform are:

iop219:
 (2) copy engines
iop321:
 (2) copy engines
 (1) xor and block fill engine
iop33x:
 (2) copy and crc32c engines
 (1) xor, xor zero sum, pq, pq zero sum, and block fill engine
iop34x (iop13xx):
 (2) copy, crc32c, xor, xor zero sum, and block fill engines
 (1) copy, crc32c, xor, xor zero sum, pq, pq zero sum, and block fill engine

The driver supports the features of the async_tx api:
* asynchronous notification of operation completion
* implicit (interupt triggered) handling of inter-channel transaction
  dependencies

The driver adapts to the platform it is running by two methods.
1/ #include <asm/arch/adma.h> which defines the hardware specific
   iop_chan_* and iop_desc_* routines as a series of static inline
   functions
2/ The private platform data attached to the platform_device defines the
   capabilities of the channels

20070626: Callbacks are run in a tasklet.  Given the recent discussion on
LKML about killing tasklets in favor of workqueues I did a quick conversion
of the driver.  Raid5 resync performance dropped from 50MB/s to 30MB/s, so
the tasklet implementation remains until a generic softirq interface is
available.

Changelog:
* fixed a slot allocation bug in do_iop13xx_adma_xor that caused too few
slots to be requested eventually leading to data corruption
* enabled the slot allocation routine to attempt to free slots before
returning -ENOMEM
* switched the cleanup routine to solely use the software chain and the
status register to determine if a descriptor is complete.  This is
necessary to support other IOP engines that do not have status writeback
capability
* make the driver iop generic
* modified the allocation routines to understand allocating a group of
slots for a single operation
* added a null xor initialization operation for the xor only channel on
iop3xx
* support xor operations on buffers larger than the hardware maximum
* split the do_* routines into separate prep, src/dest set, submit stages
* added async_tx support (dependent operations initiation at cleanup time)
* simplified group handling
* added interrupt support (callbacks via tasklets)
* brought the pending depth inline with ioat (i.e. 4 descriptors)
* drop dma mapping methods, suggested by Chris Leech
* don't use inline in C files, Adrian Bunk
* remove static tasklet declarations
* make iop_adma_alloc_slots easier to read and remove chances for a
  corrupted descriptor chain
* fix locking bug in iop_adma_alloc_chan_resources, Benjamin Herrenschmidt
* convert capabilities over to dma_cap_mask_t
* fixup sparse warnings
* add descriptor flush before iop_chan_enable
* checkpatch.pl fixes
* gpl v2 only correction
* move set_src, set_dest, submit to async_tx methods
* move group_list and phys to async_tx

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      c2110923
  69. 18 6月, 2006 1 次提交