Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739fa ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The correct bit is 24 for AHCLKX.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats.
It adds also trats specific properties for DSI.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This is a common part of DSI node for all Exynos4 boards.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch replaces panel bindings for panel initialized by boot loader
with bindings to proper ld9040 panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Switch the device tree to the new compatibles introduced in the RTC
drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IRQ line used in sun6i-a31.dtsi for the NMI controller is wrong.
This causes a IRQ storm since the NMI controller is repeatedly fired.
This patch fixes this problem assigning the correct IRQ number to the
NMI controller.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NCarlo Caione <carlo@caione.org>
Cc: maxime.ripard@free-electrons.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Link: http://lkml.kernel.org/r/1395939759-11135-2-git-send-email-carlo@caione.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

move to support of_dma_request_slave_channel() and dma_request_slave_channel.
we add a xlate() to let dma clients be able to find right dma_chan by generic
"dmas" properties in dts.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This patch adds the dts bindings documenation for the Altera SOCFPGA glue
layer for the Synopsys STMMAC ethernet driver.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH415 (Orly1)
or STiH416 (Orly2) based b2020 development board.
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH416 (Orly2).
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This reverts commit 7e0b4cd0.

The binding changes need to be done differently as well, let's
take them through netdev, and merge the dts changes in a new
patch here.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Neither Tegra114 nor Tegra124 allow "low power mode" to be configured
on SDIO1 or SDIO3 drive groups. Remove the attempt to configure that
option from the Dalmore and Venice2 DTs.

The Venice2 DT contained duplicate configurations for most sdmmc1_*
pins. Remove the duplicate pins from one of the nodes, and fix the
configuration since the remaining clk pin is output-only.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch adds DTS entries for NMI controller as child of GIC.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Cc: mark.rutland@arm.com
Cc: hdegoede@redhat.com
Acked-by: maxime.ripard@free-electrons.com
Link: http://lkml.kernel.org/r/1395256879-8475-3-git-send-email-carlo@caione.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

The patch adds fimd node with display timings for exynos4210-universal device.
It also makes LCD regulators always on. This allow to re-use panel initialized
by boot loader.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Remove some entries from Dalmore's device tree that attempt to set some
options which aren't supported for the drive_gma pin group.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

As suggested by Olof Johansson at
http://www.spinics.net/lists/arm-kernel/msg314009.html.
It be better just keeping a "ti,keystone" top-level compatible and
just using that to probe. If so we don't have to touch the file
for new boards in the future.

So use common "ti,keystone" compatible in keystone.c for all boards.

Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The UBIFS partition size was incorrectly defined as for 128M NAND,
but on k2hk-evm installed NAND flash size is 512M.
Hence, correct it.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Reviewed-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

LDO3 and LDO23 need to be enabled in order for soft-reset to work.
Additionally LDO9 needs to be enabled for USB operations.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

MDMA1 can support both secure and non-secure AXI transactions. When this
is enabled in the kernel for boards that run in secure mode, we get
imprecise external aborts causing the kernel to oops.

Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Suggested-by: NJavi Merino <javi.merino@arm.com>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Tested-by: NJavi Merino <javi.merino@arm.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add generic compatible strings to the respective board DT files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add DT data for OMAP3 N900 board. The board has the following displays:

lcd: LCD panel connected to OMAP's SDI output
tv: analog svideo
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NSebastian Reichel <sre@debian.org>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP3 IGEPv2 board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle-xM board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP4 SDP board. The board has the following displays:

lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP4 Pandaboard. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP4 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP3 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for OMAP2 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Set 'ti,set-rate-parent' property for clocks in the dpll4_m4 clock
path, which is used for DSS functional clock. This fixes DSS driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m4_ck).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NChristoph Fritz <chf.fritz@googlemail.com>
Tested-by: NMarek Belisko <marek@goldelico.com>
Acked-by: NTony Lindgren <tony@atomide.com>