We can now define the priority against BT per AC. This is
possible with a newer firmware that allows to define the
priority with 2 bits.
Note that this change is compatible with older firmware
since older firmware will simply ignore the new bit (11),
and we still set the old bit (12) in the same cases as
before.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code is really related to BT Coex - move it to the coex
file.
Also - prepare for a FW API change that will happen soon:
Bits 11 and 12 will be allocated for BT priority. Today, we
only have bit 12.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make bt-coex generic to allow other coex mechanisms.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.

With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.

The LUTs currently contain dummy values - but they will be
updated soon.

While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.

The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.

Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.

Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When indicating RF-kill toggle to the higher layer, that
may in turn call back to the transport (for MVM at least)
to turn off the device quickly. Instead of that, allow it
to return whether or not the device should be turned off,
this gets rid of the call indirection and will help make
the API more consistent when we go back to non-threaded
interrupts again for PCIe.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

1. Enable LP XTAL to avoid HW bug where device may consume much
power if FW is not loaded after device reset. LP XTAL is
disabled by default after device HW reset. Configure device's
"persistence" mode to avoid resetting XTAL again when SHRD_HW_RST
occurs in S3.

2. Add methods to access SHR (shared block memory space) directly from PCI
bus w/o need to power up MAC HW.

Shared internal registers (e.g. SHR_APMG_GP1, SHR_APMG_XTAL_CFG)can be
accessed directly from PCI bus through SHR arbiter even when MAC HW is
powered down. This is possible due to indirect read/write via
HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and HEEP_CTRL_WRD_PCIEX_DATA (0xF4)
registers.

Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW
need not be powered up so no "grab inc access" is required.

For example, to read from SHR_APMG_GP1 register (0x1DC),
first, write to the control register:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access)
second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0].

To write the register, first, write to the data register
HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access)
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When power update is initiated on BSS STA while P2P client
exists, the power command will be sent only on BSS STA vif
ignoring P2P client.

Since the firmware has symmetric constraints on the power
save enablement we can simplify the code a bit.

The current firmware doesn't know how to enable power
management on P2P client. Even BSS power management must
be disabled when a P2P client is added.

Future firmware will support power save on BSS and P2P client
as long as they are on different channels.
This was buggy since we didn't disable power management on
P2P client interface if BSS added on the same channel.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.

Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New firmware enforce valid values for the quota in D3.
The values given to the firmware when suspending and using
WoWLAN where dummy - change them to realistics values.
Tested-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Switch pos to char * which makes the code a bit shorter
as well as other minor cleanups suggested by Joe Perches.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This message triggers on systems that don't support the API,
so suppress them when not debugging as it's not useful to
see it there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise lockdep complains about the lock, I'm not sure
why we didn't see this before.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The suspend callback first sets the suspend flag used in the driver
but after that the actual suspend is done, which may fail. Reset the
flag upon suspend failure.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Even if the device is changed to 1X1 mode, data is sent with
higher MCS rates after association.

This patch fixes the problem by updating MCS information field
in HT capability when antenna setting changes so that correct
information will be advertised in association and probe request.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Command timeout happens when firmware goes into bad state.
There is no chance that next command will be successful after
this. Hence we will maintain a flag instead of count.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We already have one in mwifiex_adapter structure.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a check in command preparation routine.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of allocating a scatter-gather table for every transmit
reuse a pre-allocated table. The transmit path will be faster by
taking out this allocation.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a mismatch between the mcs index(0-7) reported to cfg80211
and the actual mcs index(0-15) in use. This patch resolves the mismatch
by setting mcs info with the number of chains read from FW.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Deauth is sent to AP when the device is acting as station at
shutdown time. Similarly we should stop AP operation also.
mwifiex_deauthenticate() takes care closing the connection
based on provided interface type.

Add a new function to simplify the code.
Reported-by: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We skip downloading other commands after FUNC_SHUTDOWN is queued
during driver unload. Main thread should be woken up each time
after freeing skipped command so that FUNC_SHUTDOWN gets served
in case if there are other pending commands before FUNC_SHUTDOWN.
Also, call mwifiex_complete_cmd() only for synchronous commands.
Reported-by: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwifiex_cancel_pending_ioctl() and
mwifiex_cancel_all_pending_cmd() are called in command timeout
and driver unload paths respectively.
If scan operation is in progress, we should abort it smoothly.
Reported-by: NTim Shepard <shep@alum.mit.edu>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently default Tx buffer size configured to firmware is 2K
for all chipsets. This patch changes it to 4K for SD/PCIe/USB
8897 chipsets as per firmware requirements.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a race condition while queuing synchronous command and
asynchronous command requested from different threads, because
the wait_q_enabled flag is set based on a global variable
cmd_wait_q_required.

The issue is fixed by removing this global variable and using a
unified function with an argument 'sync' passed into the
function.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Groupcast frames are not subject for BACK reordering because they are not
ACK'ed and one can't request re-transmitt
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

implement del_station() method in the struct cfg80211_ops
It allows to disconnect single peer from the AP
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When notifying about Rx mgmt (ex: during scan), extract
signal strength reported by the hardware.
signal is not MBM, it is arbitrary units 0..100
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID
since firmware may generate events during this call; and events need translation
table filled to be properly dispatched
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disconnect event reported by the FW, should lead to disconnection
of only requested peer. Find for the appropriate CID and disconnect
only it

For AP-like interface, notify cfg80211 with del_sta(),
for the client type interface, disconnect and turn link off.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calculate statistics per connection, report with "iw station dump"
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rx stats is not calculated per STA - just give some number
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When FW notifies about BACK status change, it provides ring ID.
Process BA status for requested connection only. As for now, FW
don't report Rx BACK status, it reports Tx one instead.
As per current algorithm used in the firmware, imply Rx BACK
state is in sync with Tx one
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardware do not support "real" broadcast on the air.
Use method similar to the Directed Multicast Service (DMS) as
described in the 10.23.15.2 "DMS procedures"

This service copies frame and delivers unicast for each associated peer

Do the following: send original frame to 1-st Tx vring, and send copies
to all other active vrings.

As currently hardware/firmware don't support A-MSDU, convert broadcast
frame to unicast instead of wrapping it in A-MSDU
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>