This converts the Nomadik pin controller and all associated device
trees to use the standard, generic config bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This converts the Nomadik pin controller and all associated device
trees to use the standard, generic mux bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Analogous to commit 8858d88a
that fixed commit 70b41abc
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.

For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

This adds the STMicroelectonics MEMS sensor devices to the Ux500
family device trees:

- Accelerometer
- Magnetometer
- Gyroscope
- Pressure (barometer)

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The mmci host driver supports the common mmc DT parser, which enables
us to use the use common names instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Move the AB8500 muxing and biasing settings over from the board
file to the device tree, include it in the reference designs using
the AB8500: HREF prior to v60, v60plus and Snowball. Set up these
GPIO lines using hogs, just like in the board file.

Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the Snowball LED pin config to the device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.

We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Ux500 boards are layered like this:
ste-snowball.dts includes ste-href.dtsi that includes
ste-dbx500.dtsi.

The dbx500.dtsi defines the PRCMU SoC regulators so the SoC will
probe and you can use ampersand references where need be.

However the HREF common dtsi and these two boards redefine the
same PRCMU SoC regulators with the very same names and properties
for no reason. This is like filling in the same line three
times instead of drawing it once. Just delete the surplus
references and have the PRCMU regulators defines in the SoC
files ste-dbx500.dtsi, this is enough.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:

- Rename the ccu8540-pinctrl.dtsi file

- Update #include statements from files using these
  files, so the build broke.

- Update the Makefile for the device trees so the build
  broke.

Fix it up so we can build them all again.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

TPS61052 is a; boost converter, LED driver, LED flash driver and
simple GPIO pin chip. It has no use here however, as it is not
found on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on this development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Regulator names are platform independent, so they need to be applied to
the base level platform DTS files *.dts. Here we're supplying the names
for the newly described AB8500 external regulators.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When this node was added, the AB8500 GPIO driver was pretty broken.
As a hack, we pretended that NOMADIK GPIO 26 was the correct on/off
pin, as it was unused. It worked because AB8500 GPIO 26 was in an
'always on from boot' state. Now the AB8500 GPIO driver is working,
the default state for all the pins is 'off'. Let's flip back over to
use the correct GPIO which is _actually_ attached to the regulator.

We're also taking the opportunity to straighten out some formatting
misdemeanours, swapping spaces for tabs.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

This removes the "0x" prefix in front of the I2C DT device
address designation for each I2C DT node in the ux500
devicetree files.
Reported-by: NBryan Wu <cooloney@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fix typo of VAMIC2 LDO regulator name in some DT-related files.  This
patch replaces all occurrences with the right name.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches to including <dt-bindings/interrupt-controller/irq.h>
and referencing the apropriate flags from there instead of
open-coding the flag numerals everywhere in the ux500 device
trees.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch prepares the use of '#define' into dts files.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In patch:
"ARM: ux500: Enable 100MHz for SD/SDIO/MMC devices"
the max frequency for the MMC/SD/SDIO adapters was
increased from 50 to 100MHz. Do the same for the
device tree boot path.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez.st@gmail.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commits:
"ARM: ux500: Add Device Tree nodes for the ux500 Crypt device"
"ARM: ux500: Add Device Tree nodes for the ux500 Hash device"

Added the crypto and hash devices conditionally, i.e. so as to
be turned on per-board by setting an "status" property on the
device from "disabled" to "okay" on each device.

This is wrong since this is an SoC feature, it is not board
dependent. It is the same ASIC under all circumstances and
functionality does not vary with board family.

This moves the enablement into the SoC file.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides information required to setup ux500-hash when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides information required to setup ux500-crypt when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Ux500 regulator name for V-INTCORE is misspelled as vinitcore instead of
vintcore in some .dts file, causing the AB8500 regulator driver to not
bind properly.  Fix this by replacing all occurrences with the right
name.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This root node is used in the whole family of chips, the a9500
is just one particular instance. Nodes should be named after
the type of object rather than identity.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: NPhilippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Until recently platform code took care of all MMCI level-shifting by
way of an ios_handler() call-back. Now it is the driver's responsibility
to handle. In order to so that we need to provide the VQMMC regulator
reference in Device Tree. This patch takes care of that.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When the thermal DT node was inserted a new PRCMU node was created;
however, one already exists in the Snowball DTS file. Here we
amalgamate the two into a single consolidated node.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>