A patchset applied earlier changed v4l2_tuner struct parameter at
vidioc_s_tuner to const. Do this change at sony_btf_mpx_s_tuner(),
in order to remove this warning:

	drivers/media/i2c/sony-btf-mpx.c:335:2: warning: initialization from incompatible pointer type [enabled by default]
	drivers/media/i2c/sony-btf-mpx.c:335:2: warning: (near initialization for 'sony_btf_mpx_tuner_ops.s_tuner') [enabled by default]

Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This API is now obsolete and can be removed.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This API is no longer used by any driver and so can be removed from the
documentation.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These ioctls are no longer used by any drivers, so remove them.

[mchehab@redhat.com: Fix merge conflict]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These ops are no longer used, so it's time to remove them.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It's no longer used, so it can now be removed.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The firmware is always the same, so drop it from the board configs. Also make
the board configs const.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Actually it's called "Group of VOP" start code in MPEG4 terminology.
Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

But now as a proper standard MPEG control.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NVolokh Konstantin <volokh84@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the other devices that need to load the boot firmware.
All firmware files are now placed in a single go7007 directory.
Also remove the device_extension_s stuff: this is clearly a left-over from
the olden days.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

All s2250 names are renamed to go7007. This will be the generic go7007
firmware loader for any go7007 device, not just for the s2250/1.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove these dummy cropping functions: cropping was never implemented.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not allocate it, but just embed in the go7007 struct.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert this driver to videobuf2 and core locking.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove struct go7007_file: all fields contained in that struct are moved to
the go7007 struct since they are really global values. The lock has just
been deleted (what's the point of a per-fh lock??).
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The s_crystal_freq operation has to be called for the saa7115 to
set up the audio clock correctly.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There really is no need to split out the board IDs for each tuner.
That's what the tuner_type is for, after all.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The go7007 produces elementary streams, so we shouldn't use the STREAM_TYPE
control, since that is for multiplexed streams.
Instead use V4L2_PIX_FMT_MPEG1/2/4.
Initially set up all the values for MPEG-2 dvd-mode, and select the dvd_mode
field if those values match that setup precisely.
Clean up lots of obsolete code relating to the custom ioctls for the MPEG
support.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- The Adlink is initially detected as a sensor board, so the driver config
  is set up as if it was a sensor. Later the driver discovers that it really
  is a video capture card and that means that the driver configuration has
  to be updated for a PAL/NTSC capture card.
- Setup the correct initial std based on the TV tuner type.
- Remember the exact std the user selected, don't map it to STD_PAL or NTSC.
- Use v4l2_disable_ioctl to disable ioctls based on the board config and
  drop a lot of checking code in each of those ioctls since that is no longer
  needed.
- enum_input should use tvnorms to fill its std field.
- configure the input, std and initial tuner frequency at driver initialization.
- fix std handling in the s2250 driver.
- the code handling scaling for devices without a scaler was broken. This is
  now fixed.
- correctly set readbuffers and capability in g/s_parm.
- remove the bogus test for capturemode in s_parm.
- correctly implement enum_framesizes/intervals.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Just add a read-only V4L2_CID_JPEG_ACTIVE_MARKER control to replace
the JPEGCOMP support.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- use the v4l2_device's release() callback
- remove the unnecessary ref_count
- don't free usb data structures on disconnect, only do that in the final
  release callback.
This is the correct way in order to safely handle disconnect and removal
of modules.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't load it everytime you stop encoding. Instead remember it.
Another reason for not loading it every time is that this could
be called from within the release() file operation, which turns
out to be deadly.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- Don't pass data allocated on the stack to usb_control_msg.
- Use dma_mapping_error after calling dma_map_page().
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It's deprecated and replaced by g_std. Since this driver already implements
g_std the use of current_norm can just be removed.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

And don't set the version field, the core does that for you.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v2 of this function doesn't do DMA to objects on the stack like
its predecessor does.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since we now know what audio inputs there are, we can also get/set and
enumerate them.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These are now no longer used and so they can be removed.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using the wis-* drivers we now use the standard 'proper' subdev
drivers.
The board configuration tables now also list the possible audio inputs,
this will be used later to implement audio inputs.
Special mention deserves a little change in set_capture_size() where the
height passed to s_mbus_fmt is doubled: that is because the saa7115 driver
expects to see the frame height, not the field height as the wis_saa7115
driver did.
Another change is that the tuner input is moved from last to the first
input, which is consistent with the common practice in other video drivers.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do i2c initialization via struct item as tw2804 has a 0x00 i2c address,
so we need to use the I2C_CLIENT_TEN flag for validity.
Signed-off-by: NVolokh Konstantin <volokh84@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>