To be able to switch on GRO on a device, ethtool_set_gro() checks this
device provides a get_rx_csum() method.

Some devices dont provide this method, while they do support RX
checksumming.

This patch allows bonding to support GRO :

ethtool -K bond0 gro on
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As RTNL is held while doing tunnels inserts and deletes, we can remove
ip6_tnl_lock spinlock. My initial RCU conversion was conservative and
converted the rwlock to spinlock, with no RTNL requirement.

Use appropriate rcu annotations and modern lockdep checks as well.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rcu_dereference_raw() now needs to know the type of its argument.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently vlan devices don't have GRO by default as none of the Ethernet
drivers add NETIF_F_GRO to their vlan_features.

As GRO is a software feature add GRO to dev->vlan_features in
register_netdevice() and let vlan_dev_init() take care that it gets
enabled only when dev->features has NETIF_F_GRO too.
Signed-off-by: NBrandon Philips <bphilips@suse.de>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev->ip_ptr is protected by rtnl and rcu.

Yet some places dont use appropriate primitives and/or locking rules.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/phonet/socket.c: In function ‘pn_res_seq_show’:
net/phonet/socket.c:726: warning: format ‘%02X’ expects type ‘unsigned int’, but argument 3 has type ‘long int’
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I wish we could use something cleaner, such as bind(). But that would
not work since resource subscription is orthogonal/in addition to the
normal object ID allocated via bind(). This is similar to multicasting
which also uses ioctl()'s.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both destination device and object are nul, Phonet routes the
packet according to the resource field. In fact, this is the most
common pattern when sending Phonet "request" packets. In this case,
the packet is delivered to whichever endpoint (socket) has
registered the resource.

This adds a new table so that Linux processes can register their
Phonet sockets to Phonet resources, if they have adequate privileges.

(Namespace support is not implemented at the moment.)
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Closing a pipe endpoint is not normally allowed by the Phonet pipe,
other than as a side after-effect of removing the pipe between two
endpoints. But there is no way to prevent Linux userspace processes
from being killed or suffering from bugs, so this can still happen.
We might as well forcefully close Phonet pipe endpoints then.

The cellular modem supports only a few existing pipes at a time. So we
really should not leak them. This change instructs the modem to destroy
the pipe if either of the pipe's endpoint (Linux socket) is closed too
early.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There may be applications trying to seek
on the irnet character device, so we should
use noop_llseek to avoid returning an error
when the default llseek changes to no_llseek.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As RTNL is held while doing tunnels inserts and deletes, we can remove
ipip6_lock spinlock. My initial RCU conversion was conservative and
converted the rwlock to spinlock, with no RTNL requirement.

Use appropriate rcu annotations and modern lockdep checks as well.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As RTNL is held while doing tunnels inserts and deletes, we can remove
ipgre_lock spinlock. My initial RCU conversion was conservative and
converted the rwlock to spinlock, with no RTNL requirement.

Use appropriate rcu annotations and modern lockdep checks as well.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As RTNL is held while doing tunnels inserts and deletes, we can remove
ipip_lock spinlock. My initial RCU conversion was conservative and
converted the rwlock to spinlock, with no RTNL requirement.

Use appropriate rcu annotations and modern lockdep checks as well.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct ethtool_rawip4_spec and struct ethtool_ether_spec are neither
commented nor used by any driver, so remove them.  Adjust padding in
the user-visible unions that included these structures.

Fix references to struct ethtool_rawip4_spec in
ethtool_get_rx_ntuple(), which should use struct ethtool_usrip4_spec.

struct ethtool_usrip4_spec cannot hold IPv6 host addresses and there
is no separate structure that can, so remove ETH_RX_NFC_IP6 and the
reference to it in niu.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This simplifies and consolidates the TX option-parsing code:

 1. The Loss Intervals option is not currently used, so dead code related to
    this option is removed. I am aware of no plans to support the option, but
    if someone wants to implement it (e.g. for inter-op tests), it is better
    to start afresh than having to also update currently unused code.

 2. The Loss Event and Receive Rate options have a lot of code in common (both
    are 32 bit, both have same length etc.), so this is consolidated.

 3. The test against GSR is not necessary, because
    - on first loading CCID3, ccid_new() zeroes out all fields in the socket;
    - ccid3_hc_tx_packet_recv() treats 0 and ~0U equivalently, due to

	pinv = opt_recv->ccid3or_loss_event_rate;
	if (pinv == ~0U || pinv == 0)
		hctx->p = 0;

    - as a result, the sequence number field is removed from opt_recv.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This removes the RTT-sampling function tfrc_tx_hist_rtt(), since

 1. it suffered from complex passing of return values (the return value both
    indicated successful lookup while the value doubled as RTT sample);

 2. when for some odd reason the sample value equalled 0, this triggered a bug
    warning about "bogus Ack", due to the ambiguity of the return value;

 3. on a passive host which has not sent anything the TX history is empty and
    thus will lead to unwanted "bogus Ack" warnings such as
    ccid3_hc_tx_packet_recv: server(e7b7d518): DATAACK with bogus ACK-28197148
    ccid3_hc_tx_packet_recv: server(e7b7d518): DATAACK with bogus ACK-26641606.

The fix is to replace the implicit encoding by performing the steps manually.

Furthermore, the "bogus Ack" warning has been removed, since it can actually be
triggered due to several reasons (network reordering, old packet, (3) above),
hence it is not very useful.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This fixes a subtle bug in the calculation of the inter-packet gap and shows
that t_delta, as it is currently used, is not needed.

The algorithm from RFC 5348, 8.3 below continually computes a send time t_nom,
which is initialised with the current time t_now; t_gran = 1E6 / HZ specifies
the scheduling granularity, s the packet size, and X the sending rate:

  t_distance = t_nom - t_now;		// in microseconds
  t_delta    = min(t_ipi, t_gran) / 2;	// `delta' parameter in microseconds

  if (t_distance >= t_delta) {
	reschedule after (t_distance / 1000) milliseconds;
  } else {
  	t_ipi  = s / X;			// inter-packet interval in usec
	t_nom += t_ipi;			// compute the next send time
	send packet now;
  }

Problem:
--------
Rescheduling requires a conversion into milliseconds (sk_reset_timer()). The
highest jiffy resolution with HZ=1000 is 1 millisecond, so using a higher
granularity does not make much sense here.

As a consequence, values of t_distance < 1000 are truncated to 0. This issue
has so far been resolved by using instead

  if (t_distance >= t_delta + 1000)
	reschedule after (t_distance / 1000) milliseconds;

This is unnecessarily large, a lower bound is t_delta' = max(t_delta, 1000).
And it implies a further simplification:

 a) when HZ >= 500, then t_delta <= t_gran/2 = 10^6/(2*HZ) <= 1000, so that
    t_delta' = MAX(1000, t_delta) = 1000 (constant value);

 b) when HZ < 500, then t_delta = 1/2*MIN(rtt, t_ipi, t_gran) <= t_gran/2,
    so that 1000 <= t_delta' <= t_gran/2.

The maximum error of using a constant t_delta in (b) is less than half a jiffy.

Fix:
----
The patch replaces t_delta with a constant, whose value depends on CONFIG_HZ,
changing the above algorithm to:

  if (t_distance >= t_delta')
	reschedule after (t_distance / 1000) milliseconds;

where t_delta' = 10^6/(2*HZ) if HZ < 500, and t_delta' = 1000 otherwise.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

Connect already has socket locking.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accept already has socket locking.

[ Extend socket locking over TCP_LISTEN state test. -DaveM ]
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accept updates socket values in 3 lines so wrapped with lock_sock.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Listen updates socket values and needs lock_sock.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate hash tables for every online cpus, not every possible ones.

NUMA aware allocations.

Dont use a full page on arches where PAGE_SIZE > 1024*sizeof(void *)

misc:
  __percpu , __read_mostly, __cpuinit annotations
  flow_compare_t is just an "unsigned long"
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that est_tree_lock is acquired with BH protection, the other
call is unnecessary.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use rcu_dereference_rtnl() helper

Change hard coded constants in fib_flag_trans()
 7 -> RTN_UNREACHABLE
 8 -> RTN_PROHIBIT
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code that trimmed excess trailing info from incoming messages
arriving over an Ethernet interface.  TIPC now ignores the extra info
while the message is being processed by the node, and only trims it off
if the message is retransmitted to another node.  (This latter step is
done to ensure the extra info doesn't cause the sk_buff to exceed the
outgoing interface's MTU limit.) The outgoing buffer is guaranteed to
be linear.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xfrm4_tunnel_register() & xfrm6_tunnel_register() should
use rcu_assign_pointer() to make sure previous writes
(to handler->next) are committed to memory before chain
insertion.

deregister functions dont need a particular barrier.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__lock_sock() and __release_sock() releases and regrabs lock but
were missing proper annotations. Add it. This removes following
warning from sparse. (Currently __lock_sock() does not emit any
warning about it but I think it is better to add also.)

 net/core/sock.c:1580:17: warning: context imbalance in '__release_sock' - unexpected unlock
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

move_addr_to_kernel() and copy_from_user() requires their argument
as __user pointer but were missing proper markups. Add it.
This removes following warnings from sparse.

 net/core/iovec.c:44:52: warning: incorrect type in argument 1 (different address spaces)
 net/core/iovec.c:44:52:    expected void [noderef] <asn:1>*uaddr
 net/core/iovec.c:44:52:    got void *msg_name
 net/core/iovec.c:55:34: warning: incorrect type in argument 2 (different address spaces)
 net/core/iovec.c:55:34:    expected void const [noderef] <asn:1>*from
 net/core/iovec.c:55:34:    got struct iovec *msg_iov
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a list_has_sctp_addr function to simplify loop

Based on a patches by Dan Carpenter and David Miller
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).

Problem is that following sequence :

fd = socket(...)
connect(fd, &remote, ...)

not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)

Sequence is :
 - autobind() : choose a random local port, insert socket in hash tables
              [while local address is INADDR_ANY]
 - connect() : set remote address and port, change local address to IP
              given by a route lookup.

When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.

One solution to this problem is to rehash datagram socket if needed.

We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.

This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: NKrzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NKrzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cmpxchg() to get rid of spinlocks in inet_add_protocol() and
friends.

inet_protos[] & inet6_protos[] are moved to read_mostly section
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two CMSGs for masked versions of cswp and fadd. args
struct modified to use a union for different atomic op type's
arguments. Change IB to do masked atomic ops. Atomic op type
in rds_message similarly unionized.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>

This prints the constant identifier for work completion status and rdma
cm event types, like we already do for IB event types.

A core string array helper is added that each string type uses.
Signed-off-by: NZach Brown <zach.brown@oracle.com>

Nothing was canceling the send and receive work that might have been
queued as a conn was being destroyed.
Signed-off-by: NZach Brown <zach.brown@oracle.com>

rds_conn_shutdown() can return before the connection is shut down when
it encounters an existing state that it doesn't understand.  This lets
rds_conn_destroy() then start tearing down the conn from under paths
that are still using it.

It's more reliable the shutdown work and wait for krdsd to complete the
shutdown callback.  This stopped some hangs I was seeing where krdsd was
trying to shut down a freed conn.
Signed-off-by: NZach Brown <zach.brown@oracle.com>

Right now there's nothing to stop the various paths that use
rs->rs_transport from racing with rmmod and executing freed transport
code.  The simple fix is to have binding to a transport also hold a
reference to the transport's module, removing this class of races.

We already had an unused t_owner field which was set for the modular
transports and which wasn't set for the built-in loop transport.
Signed-off-by: NZach Brown <zach.brown@oracle.com>

rs_transport is now also used by the rdma paths once the socket is
bound.  We don't need this stale comment to tell us what cscope can.
Signed-off-by: NZach Brown <zach.brown@oracle.com>