Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 24 6月, 2014 1 次提交
  3. 03 6月, 2014 1 次提交
    • A
      enic: Update driver to use __dev_uc/mc_sync/unsync calls · f009618a
      由 Alexander Duyck 提交于 
      This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls.  Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.

Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.

This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f009618a
  5. 31 5月, 2014 1 次提交
  7. 22 5月, 2014 1 次提交
    • S
      enic: Add support for adaptive interrupt coalescing · 7c2ce6e6
      由 Sujith Sankar 提交于 
      This patch adds support for adaptive interrupt coalescing.

For small pkts with low pkt rate, we can decrease the coalescing interrupt
dynamically which decreases the latency. This however increases the cpu
utilization. Based on testing with different coal intr and pkt rate we came up
with a table(mod_table) with rx_rate and coalescing interrupt value where we
get low latency without significant increase in cpu. mod_table table stores
the coalescing timer percentage value for different throughputs.

Function enic_calc_int_moderation() calculates the desired coalescing intr timer
value. This function is called in driver rx napi_poll. The actual value is set
by enic_set_int_moderation() which is called when napi_poll is complete. i.e
when we unmask the rx intr.

Adaptive coal intr is support only when driver is using msix intr. Because
intr is not shared.

Struct mod_range is used to store only the default adaptive coalescing intr
value.

Adaptive coal intr calue is calculated by

timer = range_start + ((rx_coal->range_end - range_start) *
		       mod_table[index].range_percent / 100);

rx_coal->range_end is the rx-usecs-high value set using ethtool.
range_start is rx-usecs-low, set using ethtool, if rx_small_pkt_bytes_cnt is
greater than 2 * rx_large_pkt_bytes_cnt. i.e small pkts are dominant. Else its
rx-usecs-low + 3.

Cc: Christian Benvenuti <benve@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7c2ce6e6
  9. 25 3月, 2014 1 次提交
  11. 15 3月, 2014 1 次提交
  13. 19 2月, 2014 1 次提交
  15. 19 12月, 2013 1 次提交
  17. 18 10月, 2013 1 次提交
  19. 06 9月, 2013 3 次提交
  21. 21 8月, 2013 2 次提交
  23. 25 7月, 2013 1 次提交
  25. 10 7月, 2013 1 次提交
  27. 20 4月, 2013 2 次提交
  29. 19 1月, 2013 1 次提交
  31. 04 1月, 2013 1 次提交
  33. 08 12月, 2012 1 次提交
  35. 04 12月, 2012 1 次提交
  37. 11 7月, 2012 1 次提交
  39. 11 5月, 2012 1 次提交
    • J
      drivers/net: Convert compare_ether_addr to ether_addr_equal · 2e42e474
      由 Joe Perches 提交于 
      Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2e42e474
  41. 02 4月, 2012 1 次提交
  43. 08 3月, 2012 1 次提交
  45. 02 3月, 2012 1 次提交
  47. 20 2月, 2012 2 次提交
  49. 18 2月, 2012 1 次提交
  51. 13 2月, 2012 1 次提交
  53. 01 2月, 2012 2 次提交
  55. 21 1月, 2012 1 次提交
  57. 19 1月, 2012 4 次提交
  59. 04 12月, 2011 1 次提交
  61. 15 11月, 2011 1 次提交