This patch moves the DMA Coalescing feature initialization code from
igb_reset to a new function and replaces it with a call to the new
function.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In 82580 and later devices, the alternate MAC address feature is
completely handled by the option ROM and software does not handle
it anymore.  This patch changes the check_alt_mac_addr function to
exit immediately if device is 82580 or later.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update adapter identification strings to properly indicate i350 VF devices
in the VF driver. Change the driver ID string to remove 82576-specific
wording. Update copyright date.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On systems that create and delete lots of dynamic devices the
31bit linux ifindex fails to fit in the 16bit macvtap minor,
resulting in unusable macvtap devices.  I have systems running
automated tests that that hit this condition in just a few days.

Use a linux idr allocator to track which mavtap minor numbers
are available and and to track the association between macvtap
minor numbers and macvtap network devices.

Remove the unnecessary unneccessary check to see if the network
device we have found is indeed a macvtap device.  With macvtap
specific data structures it is impossible to find any other
kind of networking device.

Increase the macvtap minor range from 65536 to the full 20 bits
that is supported by linux device numbers.  It doesn't solve the
original problem but there is no penalty for a larger minor
device range.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Place macvlan_common_newlink at the end of macvtap_newlink because
failing in newlink after registering your network device is not
supported.

Move device_create into a netdevice creation notifier.   The network device
notifier is the only hook that is called after the network device has been
registered with the device layer and before register_network_device returns
success.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid leaking packets in the receive queue.  Add a socket destructor
that will run whenever destroy a macvtap socket.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To see if it is appropriate to enable the macvtap zero copy feature
don't test the lowerdev network device flags.   Instead test the
macvtap network device flags which are a direct copy of the lowerdev
flags.  This is important because nothing holds a reference to lowerdev
and on a very bad day we lowerdev could be a pointer to stale memory.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a small window in macvtap_open between looking up a
networking device and calling macvtap_set_queue in which
macvtap_del_queues called from macvtap_dellink.   After
calling macvtap_del_queues it is totally incorrect to
allow macvtap_set_queue to proceed so prevent success by
reporting that all of the available queues are in use.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must account in skb->truesize, the size of the fragments, not the
used part of them.

Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
CC: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x allocates a full page per fragment.

We must account in skb->truesize, the size of the fragment, not the used
part of it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Karen Xie <kxie@chelsio.com>
Cc: linux-scsi@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the ethtool interface. The implementation is done
using the libphy helper functions.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

control these three function declarations and
definitions with same macro CONFIG_PCI_IOV

drivers/net/ethernet/intel/igb/igb_main.c:165:
warning: ‘igb_vf_configure’ declared ‘static’ but never defined
drivers/net/ethernet/intel/igb/igb_main.c:166:
warning: ‘igb_find_enabled_vfs’ declared ‘static’ but never defined
drivers/net/ethernet/intel/igb/igb_main.c:167:
warning: ‘igb_check_vf_assignment’ declared ‘static’ but never defined
Signed-off-by: NRongQing Li <roy.qing.li@gmail.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize must account for allocated memory, not the used part of
it. Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jon Mason <mason@myri.com>
Acked-by: NJon Mason <mason@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

igbvf allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize must account for allocated memory, not the used part of
it. Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove manual initialization in set_skb_frag, and instead
use __skb_fill_page_desc() to do the same. Patch tested
on net-next.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"ethtool -e ethX" dumps EEPROM data. Patch sets EEPROM length for device.
Ethtool works alot better when the kernel believes the length is > 0.

From: Allan Chou <allan@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Problem using big mtu around 4096 bytes is you end allocating (4096
+NET_SKB_PAD + NET_IP_ALIGN + sizeof(struct skb_shared_info) bytes ->
8192 bytes : order-1 pages

It's better to limit the mtu to SKB_MAX_HEAD(NET_SKB_PAD),
to have no more than one page per skb.

Also the patch changes the netdev_alloc_skb_ip_align() done in
init_dma_desc_rings() and uses a variant allowing GFP_KERNEL allocations
allowing the driver to load even in case of memory pressure.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enhances the STMMAC driver to support CHAINED mode of
descriptor.

STMMAC supports DMA descriptor to operate both in dual buffer(RING)
and linked-list(CHAINED) mode. In RING mode (default) each descriptor
points to two data buffer pointers whereas in CHAINED mode they point
to only one data buffer pointer.

In CHAINED mode each descriptor will have pointer to next descriptor in
the list, hence creating the explicit chaining in the descriptor itself,
whereas such explicit chaining is not possible in RING mode.

First version of this work has been done by Rayagond.
Then the patch has been reworked avoiding ifdef inside the C code.
A new header file has been added to define all the functions needed for
managing enhanced and normal descriptors.
In fact, these have to be specialized according to the ring/chain usage.
Two new C files have been also added to implement the helper routines
needed to manage: jumbo frames, chain and ring setup (i.e. desc3).
Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the MMC support if it is actually available from the
HW capability register.
Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows to set the mtu bigger than 1500
in case of normal descriptors.
This is helping some SPEAr customers.
Signed-off-by: NDeepak SIKRI <deepak.sikri@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a problem raised on Orly ARM SMP platform
where, in case of fragmented frames, the descriptors
in the TX ring resulted broken. This was due to a missing lock
protection in the tx process.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch stops advertising 1000Base capablities if GMAC is either
configured for MII or RMII mode and on board there is a GPHY plugged on.
Without this patch if an GBit switch is connected on MII interface,
Ethernet stops working at all.

Discovered as part of
https://bugzilla.stlinux.com/show_bug.cgi?id=14148 triage
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a network namespace misfeature that bonding_masters looked at
current instead of the remembering the context where in which
/sys/class/net/bonding_masters was opened in to see which network
namespace to act upon.

This removes the need for sysfs to handle tagged directories with
untagged members allowing for a conceptually simpler sysfs
implementation.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port shouldn't be enabled unless its current MUX
state is DISTRIBUTING which is correctly handled by
ad_mux_machine(), otherwise the packet sent can be
lost because the other end may not be ready.

The issue happens on every port initialization, but
as the ports are expected to move quickly to DISTRIBUTING,
it doesn't cause much problem.  However, it does cause
constant packet loss if the other peer has the port
configured to stay in STANDBY (i.e. SYNC set to OFF).
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Vitesse driver was using the RGMII_ID interface type to determine if
skew was necessary.  However, we want to move away from using that
interface type, as it's really a property of the board's PHY connection.
However, some boards depend on it, so we want to support it, while
allowing new boards to use the more flexible "fixups" approach.  To do
this, we extract the code which adds skew into its own function, and
call that function when RGMII_ID has been selected.

Another side-effect of this change is that if your PHY has skew set
already, it doesn't clear it.  This way, the fixup code can modify the
register without config_init then clearing it.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver version updated to 1.5.4.2
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving to Toeplitz function in RSS calculation.
Reporting rxhash in skb.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not updating common counters from data path.
The checksum counters are per ring, summarizing them when collecting statistics.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent overflow when trying to register more Vlans then the Vlan table in
HW is configured to.
Need to take into acount that the first 2 entries are reserved.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>