We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add OHCI big endian frame_no quirk.  The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field.  And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.

Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ZF Micro OHCI controller exhibits unexpected behavior that seems to be
related to high load.  Under certain conditions, the controller will
complete a TD, remove it from the endpoint's queue, and fail to add it to
the donelist. This causes the endpoint to appear to stop responding. Worse,
if the device is removed while in that state, OHCI will hang while waiting
for the orphaned TD to complete.  The situation is not recoverable without
rebooting.

This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag:

 1. A watchdog routine periodically scans the OHCI structures to check
    for orphaned TDs. In these cases the TD is taken back from the
    controller and completed normally.

 2. If a device is removed while the endpoint is hung but before the
    watchdog catches the situation, any outstanding TDs are taken back
    from the controller in the 'sanitize' phase.

The ohci-hcd driver used to print "INTR_SF lossage" in this situation;
this changes it to the universally accurate "ED unlink timeout".  Other
instances of this message presumably have different root causes.

Both this Compaq quirk and a NEC quirk are now properly compiled out for
non-PCI builds of this driver.
Signed-off-by: NMike Nuss <mike@terascala.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

readl() et.al. expect iomem pointer, so WTF force-cast it to normal one???
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a warning introduces by the split endian OHCI support
patch on platforms that don't have readl_be/writel_be variants (though
mostly harmless as those are called in an if (0) statement, but gcc
still warns).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch separates support for big endian MMIO register access
and big endian descriptors in order to support the Toshiba SCC
implementation which has big endian registers but little endian
in-memory descriptors.

It simplifies the access functions a bit in ohci.h while at it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When u132-hcd is built, it includes local header ohci.h, which appears
to have been intended only for use by ohci-hcd.

This throws warnings about functions which are defined and not used.
The warnings thrown are because three small functions are implemented in
the header, but not declared 'inline', a rather strange affair.

Since these functions are small, let's go ahead and define them as
'inline', just like the inline functions surrounding them.  This makes
things more consistent, and kills the warnings.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as790b) adds "autostop" support to ohci-hcd: the driver
will automatically stop the host controller when no devices have been
connected for at least one second.  This feature is useful when the
USB autosuspend facility isn't available, such as when
CONFIG_USB_SUSPEND hasn't been set.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".

The usbmon splits such cases already thanks to its timestamp, but
it's not always available.

I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.

The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method.  For
PCI, it is done through pci glue, for everything else through platform driver
glue.

One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now.  I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: NAleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This simplifies the OHCI root hub suspend logic:

 - Uses new usbcore root hub calls to make autosuspend work again:
	* Uses a newish usbcore root hub wakeup mechanism,
	  making requests to khubd not keventd.
	* Uses an even newer sibling suspend hook.

 - Expect someone always made usbcore call ohci_hub_suspend() before bus
   glue fires; and that ohci_hub_resume() is only called after that bus
   glue ran.  Previously, only CONFIG_USB_SUSPEND promised those things.
   (Includes updates to PCI and OMAP bus glue.)

 - Handle a not-noticed-before special case during resume from one of
   the swsusp snapshots when using "usb-handoff":  the controller isn't
   left in RESET state.  (A bug to fix in the usb-handoff code...)

Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ohci-dbg.c  |    4 ----
 drivers/usb/host/ohci-hcd.c  |    2 +-
 drivers/usb/host/ohci-hub.c  |   42 ++++++++++++------------------------------
 drivers/usb/host/ohci-mem.c  |    1 -
 drivers/usb/host/ohci-omap.c |   36 ++++++++++++------------------------
 drivers/usb/host/ohci-pci.c  |   40 ++++++++--------------------------------
 drivers/usb/host/ohci.h      |    1 -
 7 files changed, 33 insertions(+), 93 deletions(-)

Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).

It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes the HCDs that used the old hub_set_power_budget call,
making them use the new hcd->power_budget field instead.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds a reboot notifier to OHCI, mostly to benefit kexec; plus
minor #include tweaks.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation.  It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: NChris Clayton <chris_clayton@f1internet.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!