- 16 5月, 2014 5 次提交
-
-
由 Philipp Zabel 提交于
This patch enables UART1 on the phyFLEX connector (i.MX6 uart3). Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
-
由 Philipp Zabel 提交于
This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus. Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
-
由 Philipp Zabel 提交于
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
-
由 Philipp Zabel 提交于
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
-
由 Philipp Zabel 提交于
The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo phyFLEX i.MX6 modules (PFL-A-02). This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific device trees then just include the pfla01 and pbab01 dtsi files corresponding to the SoC variant. Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
-
- 21 2月, 2014 4 次提交
-
-
由 Ashutosh singh 提交于
This patch adds support for SATA on Phytec phyFLEX-i.MX6 Quad module. Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Ashutosh singh 提交于
This patch adds support for GPMI-NAND on Phytec phyFLEX-i.MX6 Quad module. Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Ashutosh singh 提交于
This patch adds support for USB_HOST on Phytec phyFLEX-i.MX6 Quad module. Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Ashutosh singh 提交于
This patch adds support for USB_OTG on Phytec phyFLEX-i.MX6 Quad module. Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 17 6月, 2013 1 次提交
-
-
由 Christian Hemp 提交于
Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01). - Module pfla02 - Carrier-Board pbab01 Signed-off-by: NChristian Hemp <c.hemp@phytec.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 09 4月, 2013 1 次提交
-
-
由 Shawn Guo 提交于
Replace /include/ (dtc) with #include (C pre-processor) for all imx DT files, so that gcc -E handles the entire include tree, and hence any of those files can #include some other file e.g. for constant definitions. This allows future use of #defines and header files in order to define names for various constants, such as pinctrl settings. Use of those features will increase the readability of the device tree files. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 10 2月, 2013 2 次提交
-
-
由 Fabio Estevam 提交于
Just to keep consistency with other dts files, place 'status' entry as the last one. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Following omap3-evm.dts way, it changes all imx dts files to use label in board dts to refer to nodes defined by soc dtsi. Thus, the board dts files become easier to read and edit with the least indentation levels. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 12 11月, 2012 1 次提交
-
-
由 Sascha Hauer 提交于
Basic support for the Ka-Ro i.MX25 based TX25 board. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Cc: Lothar Waßmann <LW@KARO-electronics.de>
-
- 02 8月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
Fix serial console node and allow the board to boot again. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 09 7月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
Add a very basic dt support for mx27_3ds (also known as mx27pdk). Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-