Provide ethtool support; with support for interrupt coalescing through
get_coalesce/set_coalesce.
Placeholders for begin/complete will be used by runtime PM
to make sure target is powered up while performing ethtool operations
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.

Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.

Fix this by adding the device mac address to the bssid mask.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AHB bus support was added in v2.6.38, through commit a0b907ee
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.

Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As suggeested by checkpatch:

WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)

In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it more readable and fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

WARNING: else is not generally useful after a break or return
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes a checkpatch warning:

WARNING: void function return statements are not generally useful
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

CHECK: No space is necessary after a cast
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

WARNING: Missing a blank line after declarations

Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

CHECK: Please don't use multiple blank lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warning:

ath10k/htt_rx.c:519: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable pulse detection on extension channel if 40MHz channel width has been set
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This happens when CONFIG_ATH9K_CHANNEL_CONTEXT is
not enabled.

../drivers/net/wireless/ath/ath9k/recv.c: In function ‘ath_rx_ps_beacon’:
../drivers/net/wireless/ath/ath9k/recv.c:553:27: error: ‘struct ath_softc’ has no member named ‘offchannel’
    if (sc->cur_chan == &sc->offchannel.chan)
                           ^
../scripts/Makefile.build:257: recipe for target 'drivers/net/wireless/ath/ath9k/recv.o' failed
make[10]: *** [drivers/net/wireless/ath/ath9k/recv.o] Error 1
../scripts/Makefile.build:404: recipe for target 'drivers/net/wireless/ath/ath9k' failed
make[9]: *** [drivers/net/wireless/ath/ath9k] Error 2
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize neighbor linked list used by dynack to compute ACK timeout
as the maximum STA ACK timeout
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ack_to entry to debugfs in order to dump current ACK timeout value
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set control frame bit in rx filter if dynack processing has been activated
in order to enable ACK frame reception
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add sampling methods for ACK RX timestamp in ath_rx_tasklet() and for TX frame
timestamp in ath_tx_complete_aggr() and in ath_tx_process_buffer(). These
samples will be used in dynack processing for ACK timeout estimation
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not overwrite ACK timeout estimation in ath9k_hw_init_global_settings() if
dynack processing has been enabled
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ACK timeout estimation algorithm to ath9k Makefile and Kconfig
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: NPhilippe Duchein <wireless-dev@duchein.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add duration field to ath_tx_status in order to report frame duration for each
entry in multi-retry chain. These fields will be used in ACK timeout estimation
algorithm (dynack)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assign 'primary_sta' to the active primary station
interface after iterating over the list of interfaces.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The opmode is verified to be NL80211_IFTYPE_STATION
before calling ath9k_set_assoc_state().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When switching offchannel, BSS related information
in the HW has to be reset to default values. Add a routine
to do this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In MCC mode, the TSF of a context needs to be
adjusted only if it is GO/AP.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The next_tbtt variable in the scheduler is needed only
for GO/AP mode operation and is always read from the
NEXT_TBTT_TIMER in the HW. There is no need to store
the timestamp for received beacons.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use empty inline functions instead of empty #define. Fix for "unused variable"
as reported below:

tree:   git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head:   167bf96d
commit: 871d8c4b [45/62] wil6210: fix usage of print_hex_dump_debug
config: i386-allyesconfig
reproduce:
  git checkout 871d8c4b
  make ARCH=i386  allyesconfig
  make ARCH=i386

All warnings:

   drivers/net/wireless/ath/wil6210/wmi.c: In function 'wmi_evt_rx_mgmt':

>> drivers/net/wireless/ath/wil6210/wmi.c:341:10: warning: unused variable 'ie_len' [-Wunused-variable]
      size_t ie_len = d_len - offsetof(struct ieee80211_mgmt,
             ^

>> drivers/net/wireless/ath/wil6210/wmi.c:340:13: warning: unused variable 'ie_buf' [-Wunused-variable]
      const u8 *ie_buf = rx_mgmt_frame->u.beacon.variable;
                ^

vim +/ie_len +341 drivers/net/wireless/ath/wil6210/wmi.c

2be7d22f Vladimir Kondratiev 2012-12-20  334
2be7d22f Vladimir Kondratiev 2012-12-20  335    if (ieee80211_is_beacon(fc) || ieee80211_is_probe_resp(fc)) {
2be7d22f Vladimir Kondratiev 2012-12-20  336            struct cfg80211_bss *bss;
8eea944a Vladimir Kondratiev 2014-06-16  337            u64 tsf = le64_to_cpu(rx_mgmt_frame->u.beacon.timestamp);
8eea944a Vladimir Kondratiev 2014-06-16  338            u16 cap = le16_to_cpu(rx_mgmt_frame->u.beacon.capab_info);
8eea944a Vladimir Kondratiev 2014-06-16  339            u16 bi = le16_to_cpu(rx_mgmt_frame->u.beacon.beacon_int);
8eea944a Vladimir Kondratiev 2014-06-16  340            const u8 *ie_buf = rx_mgmt_frame->u.beacon.variable;
8eea944a Vladimir Kondratiev 2014-06-16  341            size_t ie_len = d_len - offsetof(struct ieee80211_mgmt,
8eea944a Vladimir Kondratiev 2014-06-16  342                                             u.beacon.variable);
8eea944a Vladimir Kondratiev 2014-06-16  343            wil_dbg_wmi(wil, "Capability info : 0x%04x\n", cap);
8eea944a Vladimir Kondratiev 2014-06-16  344            wil_dbg_wmi(wil, "TSF : 0x%016llx\n", tsf);

:::::: The code at line 341 was first introduced by commit
:::::: 8eea944a wil6210: print more info about BSS found
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When interfaces of different types are present
in a context and an offchannel request is received
on a STA interface, we end up trying to process
beacons received when we are offchannel. This hits
the below warning since offchannel will not have proper
beacon parameters.

Fix this by not processing beacons received when we
are offchannel.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../drivers/net/wireless/ath/ath9k/recv.c:552 ath_rx_tasklet+0xf8f/0x1020 [ath9k]()
CPU: 1 PID: 0 Comm: swapper/1 Tainted: G           O   3.17.0-rc4-wl-debug #16
Hardware name: LENOVO 28427ZQ/INVALID, BIOS 6JET58WW (1.16 ) 09/17/2009
 0000000000000000 15916787056abba3 ffff88013b603d08 ffffffff8156af94
 ffff88013b603d50 ffff88013b603d40 ffffffff81070dbd ffff8800a84bb300
 ffff8800b05db358 ffff8800a84cc578 ffff8800a84bb300 ffff8800b05daa40
Call Trace:
 <IRQ>  [<ffffffff8156af94>] dump_stack+0x4d/0x6f
 [<ffffffff81070dbd>] warn_slowpath_common+0x7d/0xa0
 [<ffffffff81070e3c>] warn_slowpath_fmt+0x5c/0x80
 [<ffffffff81572143>] ? _raw_spin_lock_irqsave+0x83/0xa0
 [<ffffffffa09d04a6>] ? ath_rx_tasklet+0x9f6/0x1020 [ath9k]
 [<ffffffffa09d0a3f>] ath_rx_tasklet+0xf8f/0x1020 [ath9k]
 [<ffffffffa09cd4f4>] ath9k_tasklet+0xf4/0x310 [ath9k]
 [<ffffffff81075a97>] tasklet_action+0xe7/0xf0
 [<ffffffff8107508a>] __do_softirq+0x12a/0x340
 [<ffffffff8107544e>] irq_exit+0x9e/0xc0
 [<ffffffff81575e56>] do_IRQ+0x56/0xe0
 [<ffffffff81573c72>] common_interrupt+0x72/0x72
 <EOI>  [<ffffffff81421037>] ? cpuidle_enter_state+0x67/0x1a0
 [<ffffffff81421257>] cpuidle_enter+0x17/0x20
 [<ffffffff810b3ebe>] cpu_startup_entry+0x3ce/0x420
 [<ffffffff81048563>] start_secondary+0x233/0x2c0
---[ end trace f15c3e33ba78d840 ]---
------------[ cut here ]------------
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move ath9k_hw_set_radar_params() in ath9k_hw_reset() in order to avoid
AR_PHY_RADAR registers are overwritten after hw reset
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function may return an -ENODEV if debugfs is
disabled in kernel. This should originally be
guarded by ath10k's Kconfig but it still makes
sense to check for the non-NULL errno return
value.
Reported-by: NMatteo Croce <matteo@openwrt.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.1 firmware does not have an official way to
cause assert on purpose, but it can be done with
carefully crafted WMI command.  This is a different
kind of crash from the 'hard' crash, which is
a bad memory dereference.

Different crashes decode in different manners, so
this will help the crash-report testing as well as
offer better ways to test firmware failure and
recovery.

kvalo: move the wmi command creation to debug.c, modify
the info print
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We need this function to send wmi packets from testmode.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The NoA duration for a GO is half the beacon interval
and a concurrent context like a STA can be active only
for that duration, before switching back to the GO's
operating channel.

Currently, when multiple beacons are missed, the dwell
time for the STA context is extended to improve the
chances of receiving a beacon. But the NoA is not updated
and this will cause problems since the GO is offline
for a period that is longer than the advertised duration.

Fix this by ensuring that the NoA is updated first before
extending the time slot for the STA context. Also make
sure that non-periodic NoA is used for a one-time, longer
absence period.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the NoA duration is the maximum time the GO interface
can be offline, it needs to include the time take to
switch channels in the HW.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>