Add the support of ALC269VC codec.
Also delete the unnecessary codec_variant type enum list:
now only three variants (ALC269VA ALC269VB ALC269VC) are needed.

In addition, added some aliases:
 - Add ALC269VB alias name ALC277
 - Add ALC269VC alias name ALC259 ALC281X
 - Add ALC269VC for Lenovo device 0x21f3 name ALC3202
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since we now route the front DAC via aa-mix widget, adding the aa-mix
to surrounds will result in a mix-up of both front and surround PCM
signals.  For avoiding this, the aa-mix routes have to be disabled
for surround paths.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the individual DAC is available for the headphone output, the driver
should create the DAC for its volume control.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For VT1718S, the multi-channel path should be like following:
DAC 0-->Mixer 9(index 5)-->Mixer 0(index 1)-->Front Pin;
DAC 1-->Mixer 1(index 0)-->Surround Pin;
DAC 2-->C/LFE Pin;
DAC 3-->Mixer 2(index 0)-->Side Pin;

But current code built Surround and Side path through index 1 of
Mixer 1 and 2. So Adjusting Surround and Side channel amplifier is
invalid. This patch fixes the issue.
Signed-off-by: NLydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For VT1718S, Mixer 9 doesn't expose the connection to DAC 0. So when
building up a 'PCM Playback' amplifier control, it will fail since
getting DAC 0 index of Mixer 9 returned -1. So I added a dac_mixer_idx
to indicated the actual index of DAC 0 to Mixer 9. Following is the
patch and next mail is another.
Signed-off-by: NLydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Unmute DAC on front speaker path when Independent HP is enabled.

When to enable Independent HP, the front speaker won't output any sound
for VT1708, VT1708B, VT1708S and VT1702.
I find the via_independent_hp_put() routine will mute DAC 0 path in Mixer 0.
For these codecs, when using Independent HP, there could have two
independent streams, one is from DAC0-->Mixer0-->Front Pin, the other is
from DAC3-->GainSW3-->Side Pin.
So I added a check for DAC-->Mixer path in activate_output_path().

If current path is DAC-->Mixer, no need to mute DAC index in Mixer.
In fact, to change connection of Headphone pin or Mux connected with HP
is enough.
Signed-off-by: NLydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A missing initialization resulted in wrong DAC assignments in
ALC662 (and other) auto-parsers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds the re-implementation of Independent-HP mode in the
case where the DAC is shared between HP and side-channel streams.
Now the driver tries to parse the output-path using the pre-parsed
side-channel DAC for the independent HP output, too.

When a playback PCM stream is opened with this shared mode, the
Independent-HP mixer switch can't be changed for avoiding the conflict,
thus it returns -EBUSY error.

One remaining unintuitive issue is that the DAC volume is still
controlled as "Side" volume although it's shared by both independent-HP
and side streams.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move codec init verb which is only applicatable for VT1708.

I've found the root cause that jack plugged in can't be detected.
The verb in vt1708_init_verbs is used to power down jack detect circuit.
This verb is only applicable to VT1708. vt1708 didn't implement jack
detect function in hardware, so we should shut down this function to
avoid noise. But for other codecs, hardware implement jack detect
function. If sending this verb during initialization, jack detect will
be invalid. So I move this verb from via_parse_auto_config() to
patch_vt1708().
Signed-off-by: NLydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

sound/pci/hda/patch_cmedia.c: In function ‘cmi9880_fill_multi_init’:
sound/pci/hda/patch_cmedia.c:401:15: warning: unused variable ‘len’
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Let's use auto-parser as default now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Create snd_hda_get_conn_index() helper function for obtaining the
connection index of the widget.  Replaced the similar codes used in
several codec-drivers with this common helper.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix a issue to enable unsolicited response to line-out pins.
Signed-off-by: NLydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since we're not using the new auto parser as a fallback yet,
add it manually as a quirk.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Conexant ID 506c was found on Acer Aspire 3830TG. As users report
no playback, sending to stable should be safe.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/783582
Reported-by: andROOM
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use static inline for dummy function to fix the warnings like below
  sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_init’:
  sound/pci/hda/patch_sigmatel.c:4387:3: warning: statement with no effect
  sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_resume’:
  sound/pci/hda/patch_sigmatel.c:4927:3: warning: statement with no effect
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

to fix build problems when it is disabled.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

More similar fixes like previous commits: handle the exceptional case
like ALC267 where no volume amp is found in ADC widget but in the
capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select
when the pin has a single selection, and add beep verbs only when the
0x1d is used for beep.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC259 seems to provide an invalid widget capability for the input-src
selector widget.  The widget shows the input-amp while it's a selector,
and this confuses the current ALC882 initialization code that is used
for ALC259, too.  For fixing this, check the amp capability and handle
the connection selection individually.

Also, ALC259 has no mute bit in DAC volume, so we need to initialize
it as ZERO instead of MUTE.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC269 and compatible codecs have the output volume in DACs, thus we
can't use the ALC880's code as is.  Fixed by checking the amp caps and
picking up the right widget for initialization.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Look through the known NIDs that may have EAPD capabilities and turn
on/off them appropriately instead of checking the individual vendor ids.

This will also avoid the forgotten entries of newly added codec ids
in future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the regression introduced by the commit
1f0f4b80
  ALSA: hda - Reduce static init verbs for Realtek auto-parsers

The input amps of mixer widgets should be unmuted as default (as
usually they have no assigned mixer switches).

More fixes in this commit are, however, for ALC260: ALC260 codec can
have multiple output mixers connnected to a single DAC althouh the
driver didn't pick up them properly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some Realtek codecs have the output pins hardwired with certain DACs.
These DACs have to be assigned at first and assign the rest for
multi-DAC pins so that all DACs can be assigned properly.

Without such an optimization, speaker outputs may be assigned to the
same DAC as the headphone or others.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In alc_auto_add_multi_channel_mode(), when the primary HP workaround
is enabled, it re-initializes the DAC list but calls alc662's function
in a fixed way.  This isn't pretty suitable for other codecs, of course.

Now we call it with fill_dac function pointer so that the proper
function can be called at that point.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of using fixed init verbs, initialize DACs, ADCs and mixers
more dynamically for Realtek auto-parsers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a new helper function snd_hda_get_conn_list().
Unlike snd_hda_get_connections(), this function doesn't copy the
connection-list but gives the raw pointer for the cached list.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the sound/ directory there are two files (flagged by 'make
versioncheck'); sound/pci/asihpi/asihpi.c and
sound/soc/codecs/wm8991.c that include linux/version.h although they
don't need it. This patch removes the unneeded includes.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Change alc_get_line_out_pfx() in patch_realtek.c to provide the channel
specific name and assign the index so that each caller doesn't have to
set the channel name by itself.

Also, check the multi-io case with the primary hp-out; for the multi-io
channels, assign the channel name instead of "Headphone" with indices.
This makes the mixer names more intuitive and reduces confusion.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some BIOS set up the pin config wrongly as line-out although it's
supposed to be a speaker out.  In most cases, though, we can judge
the validity by checking the connection type -- when it's FIXED,
mostly it's an invalid line-out but a speaker.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Even if the machine has no line-out but only HP-out, try to detect the
multi-io.  It'll allow more possibilities for 5.1 outputs on laptops.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

- add some modules aliases
- add module license to avoid tainted kernel when loading the imx-pcm-audio
  driver
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

SND_MXC_SOC_SSI looks to be unused, so kill it.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

BIOS lists the internal speaker as an internal line-out. Change to
internal speaker + model=auto for better auto-mute capabilities.

BugLink: http://bugs.launchpad.net/bugs/754964Reported-by: NMarc Legris <marc.legris@canonical.com>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>