Otherwise, we would leave the objects in an inconsistent state, such as
write_domain == 0 but on the flushing list.
Signed-off-by: NDave Airlie <airlied@redhat.com>

obj_priv->write_domain is "write domain if the GPU went idle now", not
"write domain at this moment."  By postponing the clear, we confused the
concept, required more storage, and potentially emitted more flushes than
are required.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This fixes readpixels and buffer corruption when swapped out and in by
disabling tiling on them.

Now that we know that the bit 17 mode isn't just a mistake of older chipsets,
we'll need to work on a clever fix so that we can get the performance of
tiling on these chipsets, but that will require intrusive changes targeted
at the next kernel release, not this one.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: fix setting of max_segment_size and seg_boundary mask
  block: internal dequeue shouldn't start timer
  block: set disk->node_id before it's being used
  When block layer fails to map iov, it calls bio_unmap_user to undo

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc/83xx: Fix MCU support merge issue in mpc8349emitx.dts
  powerpc: Fix dma_map_sg() cache flushing on non coherent platforms

* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
  NLM: client-side nlm_lookup_host() should avoid matching on srcaddr
  nfsd: use of unitialized list head on error exit in nfs4recover.c
  Add a reference to sunrpc in svc_addsock
  nfsd: clean up grace period on early exit

The code used '&= 0x00002000' when it tried to set the TCO_EN bit, which
obviously didn't set that bit at all, but instead just reset all the
other bits in the SMI_EN register.

This bug seemingly caused various random behavior, with Frans Pop
reporting that X.org just silently hung at startup and Rafael Wysocki
reports the fan spinning with full speed.

See
	http://lkml.org/lkml/2008/12/3/178
	http://bugzilla.kernel.org/show_bug.cgi?id=12162

The problem seems to have been triggered by "[WATCHDOG] iTCO_wdt :
problem with rebooting on new ICH9 based motherboards" (commit
7cd5b08b), but the bogus code existed
before that too (in the "supermicro_old_pre_stop()" function), it just
apparently never showed up due to different logic.

In that commit the broken code got moved around and now gets executed
much more.
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NFrans Pop <elendil@planet.nl>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Just found the merge issue in 44274698
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.

The original patch[1] was OK though. ;-)
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.

When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.

If you create MD device over SCSI, these attributes are zeroed.

Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:

request_queue   max_segment_size  seg_boundary_mask
SCSI                65536             0xffffffff
MD RAID1                0                      0
LVM                 65536                 -1 (64bit)

Unfortunately bio_add_page (resp.  bio_phys_segments) calculates number of
physical segments according to these parameters.

During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit.  (After
bio_clone() in stack operation.)

Thi is specially problem in CCISS driver, where it produce OOPS here

    BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);

(MAXSEGENTRIES is 31 by default.)

Sometimes even this command is enough to cause oops:

  dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10

This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).

For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().

The patch tries to fix it by:

 * initializing attributes above in queue request constructor
   blk_queue_make_request()

 * make sure that blk_queue_stack_limits() inherits setting

 (DM uses its own function to set the limits because it
 blk_queue_stack_limits() was introduced later.  It should probably switch
 to use generic stack limit function too.)

 * sets the default seg_boundary value in one place (blkdev.h)

 * use this mask as default in DM (instead of -1, which differs in 64bit)

Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639
http://bugzilla.kernel.org/show_bug.cgi?id=8672Signed-off-by: NMilan Broz <mbroz@redhat.com>
Reviewed-by: NAlasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

blkdev_dequeue_request() and elv_dequeue_request() are equivalent and
both start the timeout timer.  Barrier code dequeues the original
barrier request but doesn't passes the request itself to lower level
driver, only broken down proxy requests; however, as the original
barrier code goes through the same dequeue path and timeout timer is
started on it.  If barrier sequence takes long enough, this timer
expires but the low level driver has no idea about this request and
oops follows.

Timeout timer shouldn't have been started on the original barrier
request as it never goes through actual IO.  This patch unexports
elv_dequeue_request(), which has no external user anyway, and makes it
operate on elevator proper w/o adding the timer and make
blkdev_dequeue_request() call elv_dequeue_request() and add timer.
Internal users which don't pass the request to driver - barrier code
and end_that_request_last() - are converted to use
elv_dequeue_request().
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

disk->node_id will be refered in allocating in disk_expand_part_tbl, so we
should set it before disk->node_id is refered.
Signed-off-by: NCheng Renquan <crquan@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

mapping.  Which is good if pages were mapped - but if they were provided
by someone else and just copied then bad things happen - pages are
released once here, and once by caller, leading to user triggerable BUG
at include/linux/mm.h:246.
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

On PowerPC 4xx or other non cache-coherent platforms, we lost the
appropriate cache flushing in dma_map_sg() when merging the 32 and
64-bit DMA code (commit 4fc665b8,
"powerpc: Merge 32 and 64-bit dma code").  This restores it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] hpwdt: Fix kdump when using hpwdt
  [WATCHDOG] hpwdt: set the mapped BIOS address space as executable
  [WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
  [WATCHDOG] iTCO_wdt : correct status clearing
  [WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
  [WATCHDOG] fix mtx1_wdt compilation failure

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: pre-allocate bulk-read buffer
  UBIFS: do not allocate too much
  UBIFS: do not print scary memory allocation warnings
  UBIFS: allow for gaps when dirtying the LPT
  UBIFS: fix compilation warnings
  MAINTAINERS: change UBI/UBIFS git tree URLs
  UBIFS: endian handling fixes and annotations
  UBIFS: remove printk

* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: avoid creation of unreachable pages in the shadow
  KVM: ppc: stop leaking host memory on VM exit
  KVM: MMU: fix sync of ptes addressed at owner pagetable
  KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
  KVM: ia64: Fix incorrect kbuild CFLAGS override
  KVM: VMX: Fix interrupt loss during race with NMI
  KVM: s390: Fix problem state handling in guest sigp handler

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix offset calculation in compute_size()
  rtc: rtc-starfire fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  MAINTAINERS: add netdev to ATM
  ATM: horizon, fix hrz_probe fail path
  pppol2tp: Add missing sock_put() in pppol2tp_release()
  net: Fix soft lockups/OOM issues w/ unix garbage collector
  macvlan: don't broadcast PAUSE frames to macvlan devices
  Phonet: fix oops in phonet_address_del() on non-Phonet device
  netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock
  sungem: Fix PCS_MIICTRL register write in gem_init_phy().
  net: make skb_truesize_bug() call WARN()
  net: hp-plus uses eip_poll
  net/wireless/reg.c: fix bad WARN_ON in if statement
  ath5k: disable beacon filter when station is not associated
  ath5k: fix Security issue in DebugFS part of ath5k
  ath9k: correct expected max RX buffer size
  ath9k: Fix SW-IOMMU bounce buffer starvation
  mac80211 : Fix setting ad-hoc mode and non-ibss channel
  iwlagn: fix DMA sync
  phylib: Add Vitesse VSC8221 SGMII PHY
  rose: zero length frame filtering in af_rose.c
  bridge: netfilter: fix update_pmtu crash with GRE
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Update defconfigs for 2.6.28-rc7
  macfb: Do not overflow fb_fix_screeninfo.id

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  alim15x3: fix sparse warning
  ide: remove dead code from drive_is_ready()
  ide: fix build for DEBUG_PM
  ide: respect current DMA setting during resume
  ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
  amd74xx: workaround unreliable AltStatus register for nVidia controllers
  ide: fix the ide_release_lock imbalance

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] stex: switch to block timeout
  [SCSI] make scsi_eh_try_stu use block timeout
  [SCSI] megaraid_sas: switch to block timeout
  [SCSI] ibmvscsi: switch to block timeout
  [SCSI] aacraid: switch to block timeout
  [SCSI] zfcp: prevent double decrement on host_busy while being busy
  [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
  [SCSI] zfcp: eliminate race between validation and locking
  [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
  [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
  [SCSI] zfcp: Fix opening of wka ports
  [SCSI] zfcp: fix remote port status check
  [SCSI] fc_transport: fix old bug on bitflag definitions
  [SCSI] Fix hang in starved list processing

This fixes the MN10300 kernel module linking to match the toolchain.  RELA
relocs don't use the value at the location being relocated.  This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: NMark Salter <msalter@redhat.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: NDean Nelson <dcn@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Count the insertion of new pages in the statistics used to drive the
pageout scanning code.  This should help the kernel quickly evict
streaming file IO.

We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list.  This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.

Pageout activity does its own list manipulation.
Signed-off-by: NRik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: NGene Heskett <gene.heskett@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.

On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.

This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.

[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit 731572d3) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.

But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.

This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJunjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Fix this sparse warning:

  drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We guarantee 400ns delay at the time of issuing the command.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also while at it:

* Drop unused arguments from ide_complete_power_step().

* Move DEBUG_PM printk() from ide_end_drive_cmd() to
  ide_complete_power_step().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: NMatthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode.  In order to achieve this:

* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.

* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
  driver for nVidia controllers in Compatibility Mode.

* Teach actual_try_to_identify() and drive_is_ready() about the new flag.

This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).

[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
  and distributions use) it never worked correctly. ]

Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.

More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NLars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_release_lock() spits out lots of:

	ide_release_lock: bug

warnings on Atari Falcon.

Fix the ide_release_lock imbalance.
Signed-off-by: NMichael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't overflow the 16-character fb_fix_screeninfo id string (fixes some 
console erasing and blanking artifacts). Have the ID default to "Unknown" 
on machines with no built-in video and no nubus devices. Check for 
fb_alloc_cmap failure.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (25 commits)
  em28xx: remove backward compat macro added on a previous fix
  V4L/DVB (9748): em28xx: fix compile warning
  V4L/DVB (9743): em28xx: fix oops audio
  V4L/DVB (9742): em28xx-alsa: implement another locking schema
  V4L/DVB (9732): sms1xxx: use new firmware for Hauppauge WinTV MiniStick
  V4L/DVB (9691): gspca: Move the video device to a separate area.
  V4L/DVB (9690): gspca: Lock the subdrivers via module_get/put.
  V4L/DVB (9689): gspca: Memory leak when disconnect while streaming.
  V4L/DVB (9668): em28xx: fix a race condition with hald
  V4L/DVB (9664): af9015: don't reconnect device in USB-bus
  V4L/DVB (9647): em28xx: void having two concurrent control URB's
  V4L/DVB (9646): em28xx: avoid allocating/dealocating memory on every control urb
  V4L/DVB (9645): em28xx: Avoid memory leaks if registration fails
  V4L/DVB (9639): Make dib0700 remote control support work with firmware v1.20
  V4L/DVB (9635): v4l: s2255drv fix firmware test on big-endian
  V4L/DVB (9634): Make sure the i2c gate is open before powering down tuner
  V4L/DVB (9632): make em28xx aux audio input work
  V4L/DVB (9631): Make s2api work for ATSC support
  V4L/DVB (9627): em28xx: Avoid i2c register error for boards without eeprom
  V4L/DVB (9608): Fix section mismatch warning for dm1105 during make
  ...

drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix module removal bugs of i82875p_edac.  Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.

The problems were:

1. In module removal i82875p_remove_one() is never called.

   Variable i82875p_registered is newer changed from 1, which
   guarantees i82875p_remove_one() is not called (and even if it were
   called, it would be called in wrong order).

   As a result, the edac_mc workque is not stopped and keeps probing.
   If kernel debugging options are not enabled, user may not notice
   anything going wrong.

   if debugging options are enabled and I do "rmmod i82875p_edac", I
   get:

      edac debug: edac_pci_workq_function() checking
      BUG: unable to handle kernel paging request at f882d16f
      ...
      call trace:
       [<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
       [<c0233974>] ? run_workqueue+0xd7/0x1a5
       [<c023392f>] ? run_workqueue+0x92/0x1a5
       [<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
       [<c0233af9>] ? worker_thread+0xb7/0xc3
       [<c0236a7b>] ? autoremove_wake_function+0x0/0x33
       [<c0233a42>] ? worker_thread+0x0/0xc3
       [<c0236809>] ? kthread+0x3b/0x61
       [<c02367ce>] ? kthread+0x0/0x61
       [<c0204587>] ? kernel_thread_helper+0x7/0x10

   Fix for this is to get rid of needles variable i82875p_registered
   altogether and run i82875p_remove_one() *before*
   pci_unregister_driver().

2. edac_mc_del_mc() uses mci after freeing mci

   edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device().  The
   kobject refcount of mci drops to 0 and mci is freed.  After this
   mci is accessed via debug print and i82875p_remove_one() still
   uses mci->pvt and tries to free mci again with edac_mc_free().

   The fix for this is add kobject_get(&mci->edac_mci_kobj) after
   edac_mc_alloc(). Then the mci is still available after returning
   from edac_mc_del_mc() with refcount 1, and mci->pvt is still
   available. When i82875p_remove_one() finally calls edac_mc_free(),
   this will cause kobject_put() and mci is released properly.
Signed-off-by: NJarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>