Add APB DMA requestor and serial aliases for serial controller.
There will be two serial driver i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.

The simple serial driver get enabled with compatible nvidia,tegra20-uart
and APB DMA based driver will get enabled with compatible
nvidia,tegra20-hsuart.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

tegra30 gpio controller is not compatible with the tegra20 due to
their bank stride i.e. Tegra20 bank stride is 0x80 where Tegra30
bank stride is 0x100.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed typo syntax error]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add a new evaluation board, Pluto for Tegra 114 family.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add a new evaluation board, Dalmore for Tegra 114 family.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Initial support for Tegra 114 SoC. This is expected to be included in
the board DTS files, Tegra 114 SoC based evaluation board family.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The patch to add USB PHY nodes to device tree was written before Tegra
supported the clocks property in device tree. Now that it does, add the
required clocks properties to these nodes.

This will allow all clk_get_sys() calls in tegra_usb_phy.c to be replaced
by clk_get(phy->dev, clock_name), as part of converting the PHY driver to
a platform driver.
Acked-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add clock i2c clock information to device node.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add clock information to device nodes.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: added second clock to 3d node]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add clock information to device nodes.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The device tree binding models Tegra30 CAR (Clock And Reset)
as a single monolithic clock provider.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: fixed typo in binding doc]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The Tegra20 CAR (Clock And Reset) Controller controls most aspects of
most clocks within Tegra20. The device tree binding models this as a
single monolithic clock provider, which exports many clocks. This reduces
the number of nodes needed in device tree to represent these clocks.

This binding is only useful for Tegra20; the set of clocks that exists on
Tegra30 is sufficiently different to merit its own binding.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSimon Glass <sjg@chromium.org>
[pgaikwad: Added mux clk ids and sorted CAR node]
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add CPU node for Tegra30.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add CPU node for Tegra20.
Signed-off-by: NHiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.

So, the definitions of the Ethernet interfaces is now done as follows:

 * armada-370-xp.dtsi: definitions of the first two interfaces, that
   are common to Armada 370 and Armada XP

 * armada-xp.dtsi: definition of the third interface, common to all
   Armada XP variants.

 * armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
   the fourth interface.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mplch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mpl.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The UART controller used in the Armada 370 and Armada XP SoCs is the
Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The
improper use of the ns16550 can lead to a kernel oops during boot if
a character is sent to the UART before the initialization of the
driver. The DW APB has an extra interrupt that gets raised when
writing to the LCR when busy. This explains why we need to use
dw-apb-uart driver to handle this.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In the compatible field we should point the manufacturer of the board, which
in this case is Buglabs.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Reduce the HDMI resource size from 0x100000 to 0x70000 so it
doesn't overlap the Displayport resource space.
HDMI: (0x14530000 - 0x145A0000)
DP: (0x145B0000 - 0x145B1000)
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Current nmk_pinctrl driver is not PRCMU dependent anymore, so it needs
its own DT address resources to work properly, as done for
platform_device in:

f4828336 ARM: ux500: add PRCM register base for pinctrl
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17
is the USB PHY reset.

So make the IOMUX assignment properly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit db5b0ae0 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc")
causes a duplicated build target.  This patch fixes it and sorts out the
build target alphabetically so that we can recognize something wrong
easily.

Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the rename portion of "ARM: sunxi: Change device tree naming
scheme for sunxi" that were missed when the patch was applied.
Signed-off-by: NOlof Johansson <olof@lixom.net>

There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.

Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.

So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

FEC controller is connected to AIPI2 bus.

Also fix the AIPI1 address range.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Change the value of status to disabled to keep the consistent
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit 0d9250c4 (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>