Device eswitch need to configure with VM's mac address.
Hypervisor doesn't provide any utility/callbacks to get VM's mac address.
Unicast mac address filter improves performance and also provide
packet loopback capability i.e communication between VM.

Above features is by default off, can be turned on with module parameter
'mac_learn'.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Rename mac_learning to mac_override
o Added check in set_mac to return error if mac override is disabled.
o Disabling mac_override only supported for Non priviledged functions.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o skb->mac_header is not set, so machine panics while using function eth_hdr.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Allow enabling/disabling mac anti spoof policy only for
  Non privilege functions.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Default eswitch config was set, even before eswitch capabilty get detected.
As a result setting default config was getting fail.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Mac addr was read from flash for every fw reset
for Non-priviledge function.It should be read only once.
o Remove unnecessary get_mac_addr callback
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Backing out "firmware initialization update" changes, commit-id
  "d4066833".
o fix heartbit spelling, it should be heartbeat
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there is a FW hang when the driver loads, it can not determine the FW operational
mode. Fix it by checking the FW state first before issuing any FW commands to
determine its capabilities and thereby detecting driver operational mode.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code, the error codes returned from some of the functions
are not caught and sent up the caller chain. Fixed it here.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change QLCNIC_CRB_DEV_REF_COUNT to QLCNIC_CRB_DRV_ACTIVE to match
document.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Privilege function should wait for npar state to be operational
before creating context.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On NIC Partition capable adapter, Administrator can configure to
tag packet with particular vlan id. Packet will be tagged and strip with
that vlan id. Also if 'Tagging' flag is disable, other packet will be drop.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o remove validation before deleting vlan id
o Add missing 'break' while deleting vlan id.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup legacy code which is not valid for Qlogic
CNA adapters.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mark device state failed in error path.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Privilege functions should wait for npar state to be operational.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Administrator can configure to drop packet in transmit,
if it doesn't match interface mac address, in case of virtual function.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device is not capable of enabling/disabling offload setting per
port in case of Nic Partition.So offload settings needs to be
enabled/disabled per eswitch and it will affect all the function
on that eswitch.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Nic partition capable devices has embedded switch, this needs to support
various features like external switch.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Serial number references are not used in driver.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error code is stored in the variable err, but it is the variable ret
that is returned instead.  So store the error code in ret.  Err is then
useless.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Also dont allow lro to be turn on, if rx csum is disabled
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display interface name with netdev_info() for link status message.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding eswitch statistics support. User can get
whole eswitch stats or stats of func belong to that eswitch.

Added:
o command to get statistics of eswitch and function.
o sysfs support to export eswitch and func statatistics.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

function modes was not working with CNA device, in CNA mode
other function(FCOE) can be enabled before nic.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o NPAR state should be set to operationl by Mangement function only.
o NPAR state should be set to non operational before device reset.
o VF function should wait for NPAR state to be operational.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual function are not privilge to initialize firmware.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks.  I allocated them with kcalloc()
instead.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code we allocated memory conditionally and freed it in
the error handling unconditionally.  It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function.  I
removed those checks.

Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_device_attach missing from error path in qlcnic_diag_alloc_res
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Loopback not supported for virtual function.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_get_domain_bus_and_slot: caller must decrement the
reference count by calling pci_dev_put().
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o NPAR configuration which is programmed in fw, need to
  restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pci error recovery support added.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev notifier are not unregistered if pci_register_driver fails.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable tx timeout recovery, if auto_fw_reset is disable
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Non privileged (VF) driver will not be able to carry out any of the FW update,
etc. operations. Disable the tools interface by not creating the sysfs nodes.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver checks TSO capability from FW before enabling it.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>