This fixes Ethernet on D-Link DIR-885L with BCM47094 SoC. Felix reported
similar fix was needed for his BCM4709 device (Buffalo WXR-1900DHP?).
I tested this for regressions on BCM4706, BCM4708A0 and BCM47081A0.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
ipv6: datagram: Update dst cache of a connected udp sk during pmtu update

v2:
~ Protect __sk_dst_get() operations with rcu_read_lock in
  release_cb() because another thread may do ip6_dst_store()
  for a udp sk without taking the sk lock (e.g. in sendmsg).
~ Do a ipv6_addr_v4mapped(&sk->sk_v6_daddr) check before
  calling ip6_datagram_dst_update() in patch 3 and 4.  It is
  similar to how __ip6_datagram_connect handles it.
~ One fix in ip6_datagram_dst_update() in patch 2.  It needs
  to check (np->flow_label & IPV6_FLOWLABEL_MASK) before
  doing fl6_sock_lookup.  I was confused with the naming
  of IPV6_FLOWLABEL_MASK and IPV6_FLOWINFO_MASK.
~ Check dst->obsolete just on the safe side, although I think it
  should at least have DST_OBSOLETE_FORCE_CHK by now.
~ Add Fixes tag to patch 3 and 4
~ Add some points from the previous discussion about holding
  sk lock to the commit message in patch 3.

v1:
There is a case in connected UDP socket such that
getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
sequence could be the following:
1. Create a connected UDP socket
2. Send some datagrams out
3. Receive a ICMPV6_PKT_TOOBIG
4. No new outgoing datagrams to trigger the sk_dst_check()
   logic to update the sk->sk_dst_cache.
5. getsockopt(IPV6_MTU) returns the mtu from the invalid
   sk->sk_dst_cache instead of the newly created RTF_CACHE clone.

Patch 1 and 2 are the prep work.
Patch 3 and 4 are the fixes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a release_cb for UDPv6.  It does a route lookup
and updates sk->sk_dst_cache if it is needed.  It picks up the
left-over job from ip6_sk_update_pmtu() if the sk was owned
by user during the pmtu update.

It takes a rcu_read_lock to protect the __sk_dst_get() operations
because another thread may do ip6_dst_store() without taking the
sk lock (e.g. sendmsg).

Fixes: 45e4fd26 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reported-by: NWei Wang <weiwan@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a case in connected UDP socket such that
getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
sequence could be the following:
1. Create a connected UDP socket
2. Send some datagrams out
3. Receive a ICMPV6_PKT_TOOBIG
4. No new outgoing datagrams to trigger the sk_dst_check()
   logic to update the sk->sk_dst_cache.
5. getsockopt(IPV6_MTU) returns the mtu from the invalid
   sk->sk_dst_cache instead of the newly created RTF_CACHE clone.

This patch updates the sk->sk_dst_cache for a connected datagram sk
during pmtu-update code path.

Note that the sk->sk_v6_daddr is used to do the route lookup
instead of skb->data (i.e. iph).  It is because a UDP socket can become
connected after sending out some datagrams in un-connected state.  or
It can be connected multiple times to different destinations.  Hence,
iph may not be related to where sk is currently connected to.

It is done under '!sock_owned_by_user(sk)' condition because
the user may make another ip6_datagram_connect()  (i.e changing
the sk->sk_v6_daddr) while dst lookup is happening in the pmtu-update
code path.

For the sock_owned_by_user(sk) == true case, the next patch will
introduce a release_cb() which will update the sk->sk_dst_cache.

Test:

Server (Connected UDP Socket):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Route Details:
[root@arch-fb-vm1 ~]# ip -6 r show | egrep '2fac'
2fac::/64 dev eth0  proto kernel  metric 256  pref medium
2fac:face::/64 via 2fac::face dev eth0  metric 1024  pref medium

A simple python code to create a connected UDP socket:

import socket
import errno

HOST = '2fac::1'
PORT = 8080

s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM)
s.bind((HOST, PORT))
s.connect(('2fac:face::face', 53))
print("connected")
while True:
    try:
	data = s.recv(1024)
    except socket.error as se:
	if se.errno == errno.EMSGSIZE:
		pmtu = s.getsockopt(41, 24)
		print("PMTU:%d" % pmtu)
		break
s.close()

Python program output after getting a ICMPV6_PKT_TOOBIG:
[root@arch-fb-vm1 ~]# python2 ~/devshare/kernel/tasks/fib6/udp-connect-53-8080.py
connected
PMTU:1300

Cache routes after recieving TOOBIG:
[root@arch-fb-vm1 ~]# ip -6 r show table cache
2fac:face::face via 2fac::face dev eth0  metric 0
    cache  expires 463sec mtu 1300 pref medium

Client (Send the ICMPV6_PKT_TOOBIG):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scapy is used to generate the TOOBIG message.  Here is the scapy script I have
used:

>>> p=Ether(src='da:75:4d:36:ac:32', dst='52:54:00:12:34:66', type=0x86dd)/IPv6(src='2fac::face', dst='2fac::1')/ICMPv6PacketTooBig(mtu=1300)/IPv6(src='2fac::
1',dst='2fac:face::face', nh='UDP')/UDP(sport=8080,dport=53)
>>> sendp(p, iface='qemubr0')

Fixes: 45e4fd26 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reported-by: NWei Wang <weiwan@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the route lookup and update codes for connected
datagram sk to a newly created function ip6_datagram_dst_update()

It will be reused during the pmtu update in the later patch.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move flowi6 init codes for connected datagram sk to a newly created
function ip6_datagram_flow_key_init().

Notes:
1. fl6_flowlabel is used instead of fl6.flowlabel in __ip6_datagram_connect
2. ipv6_addr_is_multicast(&fl6->daddr) is used instead of
   (addr_type & IPV6_ADDR_MULTICAST) in ip6_datagram_flow_key_init()

This new function will be reused during pmtu update in the later patch.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current binding document only describes a single interrupt. Update the
document by adding the 2 other interrupts.

The driver currently only uses a single interrupt. The HW is however able
to using IRQ grouping to split TX and RX onto separate GIC irqs.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: devicetree@vger.kernel.org
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
This has just the single fix from Dmitry Ivanov, adding the missing
netlink notifier family check to avoid the socket close DoS problem.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

verifier must check for reserved size bits in instruction opcode and
reject BPF_LD | BPF_ABS | BPF_DW and BPF_LD | BPF_IND | BPF_DW instructions,
otherwise interpreter will WARN_RATELIMIT on them during execution.

Fixes: ddd872bc ("bpf: verifier: add checks for BPF_ABS | BPF_IND instructions")
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A failure in validate_xmit_skb_list() triggered an unconditional call
to dev_requeue_skb with skb=NULL. This slowly grows the queue
discipline's qlen count until all traffic through the queue stops.

We take the optimistic approach and continue running the queue after a
failure since it is unknown if later packets also will fail in the
validate path.

Fixes: 55a93b3e ("qdisc: validate skb without holding lock")
Signed-off-by: NLars Persson <larper@axis.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because we miss to wipe the remainder of i->addr[] in packet_mc_add(),
pdiag_put_mclist() leaks uninitialized heap bytes via the
PACKET_DIAG_MCLIST netlink attribute.

Fix this by explicitly memset(0)ing the remaining bytes in i->addr[].

Fixes: eea68e2f ("packet: Report socket mclist info via diag module")
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: NPavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-04-13

This series contains updates to i40e, i40evf and fm10k.

Alex fixes a bug introduced earlier based on his interpretation of the
XL710 datasheet.  The actual limit for fragments with TSO and a skbuff
that has payload data in the header portion of the buffer is actually
only 7 fragments and the skb-data portion counts as 2 buffers, one for
the TSO header, and the one for a segment payload buffer.

Jacob fixes a bug where in a previous refactor of the code broke
multi-bit updates for VFs.  The problem occurs because a multi-bit
request has a non-zero length, and the PF would simply drop any
request with the upper 16 bits set.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For local routes that require a particular output interface we do not want
to cache the result.  Caching the result causes incorrect behaviour when
there are multiple source addresses on the interface.  The end result
being that if the intended recipient is waiting on that interface for the
packet he won't receive it because it will be delivered on the loopback
interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
interface as well.

This can be tested by running a program such as "dhcp_release" which
attempts to inject a packet on a particular interface so that it is
received by another program on the same board.  The receiving process
should see an IP_PKTINFO ipi_ifndex value of the source interface
(e.g., eth1) instead of the loopback interface (e.g., lo).  The packet
will still appear on the loopback interface in tcpdump but the important
aspect is that the CMSG info is correct.

Sample dhcp_release command line:

   dhcp_release eth1 192.168.204.222 02:11:33:22:44:66
Signed-off-by: NAllain Legacy <allain.legacy@windriver.com>
Signed off-by: Chris Friesen <chris.friesen@windriver.com>
Reviewed-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.

We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit b7d3e3d3 ("net: thunderx: Don't leak phy device references
on -EPROBE_DEFER condition.") incorrectly moved the call to
of_node_put() outside of the loop.  Under normal loop exit, the node
has already had of_node_put() called, so the extra call results in:

[    8.228020] ERROR: Bad of_node_put() on /soc@0/pci@848000000000/mrml-bridge0@1,0/bgx0/xlaui00
[    8.239433] CPU: 16 PID: 608 Comm: systemd-udevd Not tainted 4.6.0-rc1-numa+ #157
[    8.247380] Hardware name: www.cavium.com EBB8800/EBB8800, BIOS 0.3 Mar  2 2016
[    8.273541] Call trace:
[    8.273550] [<fffffc0008097364>] dump_backtrace+0x0/0x210
[    8.273557] [<fffffc0008097598>] show_stack+0x24/0x2c
[    8.273560] [<fffffc0008399ed0>] dump_stack+0x8c/0xb4
[    8.273566] [<fffffc00085aa828>] of_node_release+0xa8/0xac
[    8.273570] [<fffffc000839cad8>] kobject_cleanup+0x8c/0x194
[    8.273573] [<fffffc000839c97c>] kobject_put+0x44/0x6c
[    8.273576] [<fffffc00085a9ab0>] of_node_put+0x24/0x30
[    8.273587] [<fffffc0000bd0f74>] bgx_probe+0x17c/0xcd8 [thunder_bgx]
[    8.273591] [<fffffc00083ed220>] pci_device_probe+0xa0/0x114
[    8.273596] [<fffffc0008473fbc>] driver_probe_device+0x178/0x418
[    8.273599] [<fffffc000847435c>] __driver_attach+0x100/0x118
[    8.273602] [<fffffc0008471b58>] bus_for_each_dev+0x6c/0xac
[    8.273605] [<fffffc0008473884>] driver_attach+0x30/0x38
[    8.273608] [<fffffc00084732f4>] bus_add_driver+0x1f8/0x29c
[    8.273611] [<fffffc0008475028>] driver_register+0x70/0x110
[    8.273617] [<fffffc00083ebf08>] __pci_register_driver+0x60/0x6c
[    8.273623] [<fffffc0000bf0040>] bgx_init_module+0x40/0x48 [thunder_bgx]
[    8.273626] [<fffffc0008090d04>] do_one_initcall+0xcc/0x1c0
[    8.273631] [<fffffc0008198abc>] do_init_module+0x68/0x1c8
[    8.273635] [<fffffc0008125668>] load_module+0xf44/0x11f4
[    8.273638] [<fffffc0008125b64>] SyS_finit_module+0xb8/0xe0
[    8.273641] [<fffffc0008093b30>] el0_svc_naked+0x24/0x28

Go back to the previous (correct) code that only did the extra
of_node_put() call on early exit from the loop.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add validation code into mISDN/socket.c
Signed-off-by: NEmrah Demir <ed@abdsec.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet.  Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)."  It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.

I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.

Fixes: 2d37490b ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

f1705ec1 added the option to retain user configured addresses on an
admin down. A comment to one of the later revisions suggested using the
IFA_F_PERMANENT flag rather than adding a user_managed boolean to the
ifaddr struct. A side effect of this change is that link local and
loopback addresses are also retained which is not part of the objective
of f1705ec1. Add check to drop those addresses.

Fixes: f1705ec1 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree. More
specifically, they are:

1) Fix missing filter table per-netns registration in arptables, from
   Florian Westphal.

2) Resolve out of bound access when parsing TCP options in
   nf_conntrack_tcp, patch from Jozsef Kadlecsik.

3) Prefer NFPROTO_BRIDGE extensions over NFPROTO_UNSPEC in ebtables,
   this resolves conflict between xt_limit and ebt_limit, from Phil Sutter.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.6

b43

* fix memory leaks when removing the device

bcma

* fix building without OF_IRQ

rtlwifi

* fix gcc-6 indentation warning

iwlwifi

* lower the debug level of a benign print
* fix a memory leak
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a requested extension exists as module and is not loaded,
ebt_check_match() might accidentally use an NFPROTO_UNSPEC one with same
name and fail.

Reproduced with limit match: Given xt_limit and ebt_limit both built as
module, the following would fail:

  modprobe xt_limit
  ebtables -I INPUT --limit 1/s -j ACCEPT

The fix is to make ebt_check_match() distrust a found NFPROTO_UNSPEC
extension and retry after requesting an appropriate module.

Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.

Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.

Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.

Fixes: 026331c4 ("cfg80211/mac80211: allow registering for and sending action frames")
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new devlink.h in uapi was not being installed by
make headers_install
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ifupdown2 found a kernel bug with IPv6 routes and movement from the main
table to the VRF table. Sequence of events:

Create the interface and add addresses:
    ip link add dev eth4.105 link eth4 type vlan id 105
    ip addr add dev eth4.105 8.105.105.10/24
    ip -6 addr add dev eth4.105 2008:105:105::10/64

At this point IPv6 has inserted a prefix route in the main table even
though the interface is 'down'. From there the VRF device is created:
    ip link add dev vrf105 type vrf table 105
    ip addr add dev vrf105 9.9.105.10/32
    ip -6 addr add dev vrf105 2000:9:105::10/128
    ip link set vrf105 up

Then the interface is enslaved, while still in the 'down' state:
    ip link set dev eth4.105 master vrf105

Since the device is down the VRF driver cycling the device does not
send the NETDEV_UP and NETDEV_DOWN but rather the NETDEV_CHANGE event
which does not flush the routes inserted prior.

When the link is brought up
    ip link set dev eth4.105 up

the prefix route is added in the VRF table, but does not remove
the route from the main table.

Fix by handling the NETDEV_CHANGEUPPER event similar what was implemented
for IPv4 in 7f49e7a3 ("net: Flush local routes when device changes vrf
association")

Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivek reported a kernel exception deleting a VRF with an active
connection through it. The root cause is that the socket has a cached
reference to a dst that is destroyed. Converting the dst_destroy to
dst_release and letting proper reference counting kick in does not
work as the dst has a reference to the device which needs to be released
as well.

I talked to Hannes about this at netdev and he pointed out the ipv4 and
ipv6 dst handling has dst_ifdown for just this scenario. Rather than
continuing with the reinvented dst wheel in VRF just remove it and
leverage the ipv4 and ipv6 versions.

Fixes: 193125db ("net: Introduce VRF device driver")
Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: name distributor pernet queue

Commit #1 fixes a potential issue with deferred binding table
updates being pushed to the wrong namespace.

Commit #2 solves a problem with deferred binding table updates
remaining in the the defer queue after the issuing node has gone
down.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a peer node becomes unavailable, in addition to removing the
nametable entries from this node we also need to purge all deferred
updates associated with this node.
Signed-off-by: NErik Hugne <erik.hugne@gmail.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nametable updates received from the network that cannot be applied
immediately are placed on a defer queue. This queue is global to the
TIPC module, which might cause problems when using TIPC in containers.
To prevent nametable updates from escaping into the wrong namespace,
we make the queue pernet instead.
Signed-off-by: NErik Hugne <erik.hugne@gmail.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.

One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using the PTP fpga to hps clock source for the stmmac module
the appropriate bit in the System Manager FPGA Interface Group register
needs to be set. This is not set by the bootloader setup  when the
HPS emac pins are being for this emac module.

This allows the PTP clock to be sourced from the FPGA and also connects
the PTP pps and ext trig signals to the stmmac PTP hardware.

Patch proposed by Phil Collins.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All existing users of NETLINK_URELEASE use it to clean up resources that
were previously allocated to a socket via some command. As a result, no
users require getting this notification for unbound sockets.

Sending it for unbound sockets, however, is a problem because any user
(including unprivileged users) can create a socket that uses the same ID
as an existing socket. Binding this new socket will fail, but if the
NETLINK_URELEASE notification is generated for such sockets, the users
thereof will be tricked into thinking the socket that they allocated the
resources for is closed.

In the nl80211 case, this will cause destruction of virtual interfaces
that still belong to an existing hostapd process; this is the case that
Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
of netlink log/queue it will cause them to stop reporting events, as if
NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.

Fix this problem by checking that the socket is bound before generating
the NETLINK_URELEASE notification.

Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Ivanov <dima@ubnt.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In particular, make sure we check for decnet private presence
for loopback devices.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently on high rate SCTP streams the heartbeat timer refresh can
consume quite a lot of resources as timer updates are costly and it
contains a random factor, which a) is also costly and b) invalidates
mod_timer() optimization for not editing a timer to the same value.
It may even cause the timer to be slightly advanced, for no good reason.

As suggested by David Laight this patch now removes this timer update
from hot path by leaving the timer on and re-evaluating upon its
expiration if the heartbeat is still needed or not, similarly to what is
done for TCP. If it's not needed anymore the timer is re-scheduled to
the new timeout, considering the time already elapsed.

For this, we now record the last tx timestamp per transport, updated in
the same spots as hb timer was restarted on tx. Also split up
sctp_transport_reset_timers into sctp_transport_reset_t3_rtx and
sctp_transport_reset_hb_timer, so we can re-arm T3 without re-arming the
heartbeat one.

On loopback with MTU of 65535 and data chunks with 1636, so that we
have a considerable amount of chunks without stressing system calls,
netperf -t SCTP_STREAM -l 30, perf looked like this before:

Samples: 103K of event 'cpu-clock', Event count (approx.): 25833000000
  Overhead  Command  Shared Object      Symbol
+    6,15%  netperf  [kernel.vmlinux]   [k] copy_user_enhanced_fast_string
-    5,43%  netperf  [kernel.vmlinux]   [k] _raw_write_unlock_irqrestore
   - _raw_write_unlock_irqrestore
      - 96,54% _raw_spin_unlock_irqrestore
         - 36,14% mod_timer
            + 97,24% sctp_transport_reset_timers
            + 2,76% sctp_do_sm
         + 33,65% __wake_up_sync_key
         + 28,77% sctp_ulpq_tail_event
         + 1,40% del_timer
      - 1,84% mod_timer
         + 99,03% sctp_transport_reset_timers
         + 0,97% sctp_do_sm
      + 1,50% sctp_ulpq_tail_event

And after this patch, now with netperf -l 60:

Samples: 230K of event 'cpu-clock', Event count (approx.): 57707250000
  Overhead  Command  Shared Object      Symbol
+    5,65%  netperf  [kernel.vmlinux]   [k] memcpy_erms
+    5,59%  netperf  [kernel.vmlinux]   [k] copy_user_enhanced_fast_string
-    5,05%  netperf  [kernel.vmlinux]   [k] _raw_spin_unlock_irqrestore
   - _raw_spin_unlock_irqrestore
      + 49,89% __wake_up_sync_key
      + 45,68% sctp_ulpq_tail_event
      - 2,85% mod_timer
         + 76,51% sctp_transport_reset_t3_rtx
         + 23,49% sctp_do_sm
      + 1,55% del_timer
+    2,50%  netperf  [sctp]             [k] sctp_datamsg_from_user
+    2,26%  netperf  [sctp]             [k] sctp_sendmsg

Throughput-wise, from 6800mbps without the patch to 7050mbps with it,
~3.7%.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The E-MAC interrupts are left disabled when the ring parameters are changed
via 'ethtool'. In order to fix this, it's enough to call sh_eth_dev_init()
with 'true' instead of 'false' for the second argument (which conveniently
allows us to remove the following code re-enabling E-DMAC interrupts and
reception).
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id

Pull SCSI fixes from James Bottomley:
 "This is a set of eight fixes.

  Two are trivial gcc-6 updates (brace additions and unused variable
  removal).  There's a couple of cxlflash regressions, a correction for
  sd being overly chatty on revalidation (causing excess log increases).
  A VPD issue which could crash USB devices because they seem very
  intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
  overrun fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Do not attach VPD to devices that don't support it
  sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
  scsi_dh_alua: Fix a recently introduced deadlock
  scsi: Declare local symbols static
  cxlflash: Move to exponential back-off when cmd_room is not available
  cxlflash: Fix regression issue with re-ordering patch
  mpt3sas: Don't overreach ioc->reply_post[] during initialization
  aacraid: add missing curly braces

Pull MD fixes from Shaohua Li:
 "This update mainly fixes bugs:

   - fix error handling (Guoqing)
   - fix a crash when a disk is hotremoved (me)
   - fix a dead loop (Wei Fang)"

* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: clear bitmap if bitmap_create failed
  MD: add rdev reference for super write
  md: fix a trivial typo in comments
  md:raid1: fix a dead loop when read from a WriteMostly disk