Since both tx and rx paths work with skb->vlan_tci, there's no need for
this function anymore. Switch users directly to __vlan_hwaccel_put_tag.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always returns the same skb it gets, so change to void.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel.  When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets.  This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.

There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver.  These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb.  When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.

The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued.  The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0

This connection finally times out.

I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver.  There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.

The patch attempt to fix this another way.  It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core.  This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.

CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new function vlan_get_encap_level() uses vlan_dev_priv()
which is only conditionally avaialble when VLAN support is
enabled.  Make vlan_get_encap_level() conditionally available
as well.

Fixes: 44a40855 ("bonding: Fix stacked device detection in arp monitoring")
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to commit fbd929f2
	bonding: support QinQ for bond arp interval

the arp monitoring code allowed for proper detection of devices
stacked on top of vlans.  Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device.  However, this is not always the
case, as it is possible to extend the stacked configuration.

With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.

For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan

Note:  This patch limites the number of stacked VLANs to 2,
just like before.  The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic.  This is no longer
possible.

Fixes: fbd929f2 (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit dc8eaaa0.
	vlan: Fix lockdep warning when vlan dev handle notification

Instead we use the new new API to find the lock subclass of
our vlan device.  This way we can support configurations where
vlans are interspersed with other devices:
  bond -> vlan -> macvlan -> vlan
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kfree_skb with dev_kfree_skb_any in vlan_insert_tag as
vlan_insert_tag can be called from hard irq context (netpoll)
and from other contexts.

dev_kfree_skb_any is used as vlan_insert_tag only frees the skb if the
skb can not be modified to insert a tag, in which case vlan_insert_tag
drops the skb.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

macvlan needs vlan_pcpu_stats so make it visible even if compiling
without VLAN_8021Q support. Otherwise a very long compiler error happens.

Fixes: cdf3e274 ("macvlan: unify macvlan_pcpu_stats and vlan_pcpu_stats")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-By: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid very silly Kconfig dependencies for modules
using this routine.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a method for read-only access to the vlan device egress mapping.

Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.

Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a96865 "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 48cc32d3
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.

But we also have a problem if prio bits are set.

Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.

Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :

16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
       0x0000:  0000 0029 8000 c7c3 7103 0001 a0ae e651
       0x0010:  0000 0000 ccce 0b00 0000 0000 1011 1213
       0x0020:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
       0x0030:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233

It seems we are not really ready to properly cope with this right now.

We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.

For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: NSteinar H. Gunderson <sesse@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After addition of 8021AD h_vlan_proto can be either ETH_P_8021Q or
ETH_P_8021AD.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the definition of HAVE_VLAN_PUT_TAG since it's not
used or exported anywhere.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up some function signatures for CONFIG_VLAN=n that were missed during
the 802.1ad support patches.

Found by the kbuild robot.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.

Configuration is done using "ip link":

# ip link add link eth0 eth0.1000 \
	type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
	type vlan proto 802.1q id 1000

52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
    20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
    20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.

Also update all the users of this value that David Miller and
I could find to use the new constant.

Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.

As suggested by Jesse Gross.

Compile tested only.

Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two places to call vlan_set_encap_proto():
vlan_untag() and __pop_vlan_tci().

vlan_untag() assumes skb->data points after mac addr, otherwise
the following code

        vhdr = (struct vlan_hdr *) skb->data;
        vlan_tci = ntohs(vhdr->h_vlan_TCI);
        __vlan_hwaccel_put_tag(skb, vlan_tci);

        skb_pull_rcsum(skb, VLAN_HLEN);

won't be correct. But __pop_vlan_tci() assumes points _before_
mac addr.

In vlan_set_encap_proto(), it looks for some magic L2 value
after mac addr:

        rawp = skb->data;
        if (*(unsigned short *) rawp == 0xFFFF)
	...

Therefore __pop_vlan_tci() is obviously wrong.

A quick fix is avoiding using skb->data in vlan_set_encap_proto(),
use 'vhdr+1' is always correct in both cases.

Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

6a32e4f9 made the vlan code skip marking
vlan-tagged frames for not locally configured vlans as PACKET_OTHERHOST if
there was an rx_handler, as the rx_handler could cause the frame to be received
on a different (virtual) vlan-capable interface where that vlan might be
configured.

As rx_handlers do not necessarily return RX_HANDLER_ANOTHER, this could cause
frames for unknown vlans to be delivered to the protocol stack as if they had
been received untagged.

For example, if an ipv6 router advertisement that's tagged for a locally not
configured vlan is received on an interface with macvlan interfaces attached,
macvlan's rx_handler returns RX_HANDLER_PASS after delivering the frame to the
macvlan interfaces, which caused it to be passed to the protocol stack, leading
to ipv6 addresses for the announced prefix being configured even though those
are completely unusable on the underlying interface.

The fix moves marking as PACKET_OTHERHOST after the rx_handler so the
rx_handler, if there is one, sees the frame unchanged, but afterwards,
before the frame is delivered to the protocol stack, it gets marked whether
there is an rx_handler or not.
Signed-off-by: NFlorian Zumbiehl <florz@florz.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also, remove unused vlan_info definition from header

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just use ETH_ALEN.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.

We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Introduce functions handy to copy vlan ids from one driver's list to
another.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows to keep track of vids needed to be in rx vlan filters of
devices even if they are used in bond/team etc.

vlan_info as well as vlan_group previously was, is allocated when first
vid is added and dealocated whan last vid is deleted.

vlan_group definition is moved to private header.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As this structure is priv, name it approprietely. Also for pointer to it
use name "vlan".
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Open vSwitch needs this function for vlan handling.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

commit 2425717b (net: allow vlan traffic to be received under bond)
broke ARP processing on vlan on top of bonding.

       +-------+
eth0 --| bond0 |---bond0.103
eth1 --|       |
       +-------+

52870.115435: skb_gro_reset_offset <-napi_gro_receive
52870.115435: dev_gro_receive <-napi_gro_receive
52870.115435: napi_skb_finish <-napi_gro_receive
52870.115435: netif_receive_skb <-napi_skb_finish
52870.115435: get_rps_cpu <-netif_receive_skb
52870.115435: __netif_receive_skb <-netif_receive_skb
52870.115436: vlan_do_receive <-__netif_receive_skb
52870.115436: bond_handle_frame <-__netif_receive_skb
52870.115436: vlan_do_receive <-__netif_receive_skb
52870.115436: arp_rcv <-__netif_receive_skb
52870.115436: kfree_skb <-arp_rcv

Packet is dropped in arp_rcv() because its pkt_type was set to
PACKET_OTHERHOST in the first vlan_do_receive() call, since no eth0.103
exists.

We really need to change pkt_type only if no more rx_handler is about to
be called for the packet.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

there are no users outside vlan code
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since vlan_group_get_device and vlan_group is not going to be accessible
from device drivers, introduce function which substitutes it.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

else case remained forgotten.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>