Since both tx and rx paths work with skb->vlan_tci, there's no need for
this function anymore. Switch users directly to __vlan_hwaccel_put_tag.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add myself to the list of copyright holders.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add generic interrupt-config callback and store interrupt-level bitmask
in type data for PHY types not using bit 9.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select
bit, which is used to select 25 or 50 MHz clock mode.

Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of
this bit is inverted so that setting it enables 25 rather than 50 MHz
mode. Add a new device-tree property
"micrel,rmii-reference-clock-select-25-mhz" to describe this.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add generic RMII-Reference-Clock-Select support.

Several Micrel PHY have an RMII-Reference-Clock-Select bit to select
25 MHz or 50 MHz clock mode. Recently, support for configuring this
through device tree for KSZ8021 and KSZ8031 was added.

Generalise this support so that it can be configured for other PHY types
as well.

Note that some PHY revisions (of the same type) has this bit inverted.
This should be either configurable through a new device-tree property,
or preferably, determined based on PHY ID if possible.

Also note that this removes support for setting 25 MHz mode from board
files which was also added by the above mentioned commit 45f56cb82e45
("net/phy: micrel: Add clock support for KSZ8021/KSZ8031").
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add has_broadcast_disable flag to type-data and generic config_init.

This allows us to remove the ksz8081 config_init callback.

Note that ksz8021_config_init is kept for now due to a95a18afe4c8
("phy/micrel: KSZ8031RNL RMII clock reconfiguration bug").
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parse the "micrel,led-mode" property at probe, rather than at config_init
time in the led-setup helper itself.

Note that the bogus parent->of_node bit is removed.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add structured device-type information and support for generic led-mode
setup to the generic config_init callback.

This is a first step in ultimately getting rid of device-type specific
callbacks.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to a random RSS key rather than a fixed one.
Using netdev_rss_key_fill helper also ensures that all ports share
a common key.

See also commit 960fb622.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check and update posted_index only when skb->xmit_more is 0 or tx queue is full.

v2:
use txq_map instead of skb_get_queue_mapping(skb)
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds [2.5|20|40|56] Gbps enum definition, and fixes
aggregated bandwidth calculation based on above slave links.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NJianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port Key was determined as 16 bits according to the link speed,
duplex and user key (which is yet not supported).  In the old
speed field, 5 bits are for speed [1|10|100|1000|10000]Mbps as
below:
--------------------------------------------------------------
Port key :| User key        | Speed         |       Duplex|
--------------------------------------------------------------
    16                  6               1               0
This patch keeps the old layout, but changes AD_LINK_SPEED_BITMASK
from bit type to an enum type.  In this way, the speed field can
expand speed type from 5 to 32.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NJianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove unused variable
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When run ./scripts/kernel-doc several warnings are reported
so this patch fix them.
Also it reviews many comments and adds new ones.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some useful comments inside the common header
file to provide information about the APIs exposed by the driver.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 5d097109
("tun: only queue packets on device"), NETDEV_TX_OK was returned for
dropped packets. This will confuse pktgen since dropped packets were
counted as sent ones.

Fixing this by returning NET_XMIT_DROP to let pktgen count it as error
packet.

Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The return value of swap_buffer() is not used by any caller, thus
remove it.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate the DIV_ROUND_UP() and change the loop counter increment to
4 instead. This results in saving 6 instructions in the functions
assembly code.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when swap_buffer() is being called, we know for sure, that we need to
byte swap the data. Furthermore, this function is called for swapping
data in both directions. Thus cpu_to_be32() is semantically not
correct for all use cases. Use swab32s() to reflect this.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fep->bufdesc_ex is treated as a boolean value, thus declare it as
such.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

consistently use TABs for indentation
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.

This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.

Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When PFC is enabled we should not proceed with setting the link flow control
parameters.  Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.

Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.

The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.

Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.

Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.

Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.

So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.

This patch fixes this issue.

Change-ID: Ife5694469b05494228e0d850429ea1734738cf29
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.

Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.

Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.

This patch adds this call to the flow that handles DCB re-configuration in
the PF.

Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bumping minor version as this will be the second SW release and it
should be 1.

Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.

To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.

This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.

Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only warn once that PTP is not supported when linked at 100Mbit.

Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports.  That should be plenty.

Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.

To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>