Until now, in order to offload a FIB entry to HW we use switchdev op.
However that has limits. Mainly in case we need to make the HW aware of
all route prefixes configured in kernel. HW needs to know those in order
to properly trap appropriate packets and pass the to kernel to do
the forwarding. Abort mechanism is now handled within the mlxsw driver.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These helpers are to be used in case someone offloads the FIB entry. The
result is that if the entry is offloaded to at least one device, the
offload flag is set.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows to pass information about added/deleted FIB entries/rules to
whoever is interested. This is done in a very similar way as devinet
notifies address additions/removals.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code use the encapsulation key id value as the mask of that
parameter which is wrong. Fix that by using a full mask.

Fixes: bc3103f1 ('net/sched: cls_flower: Classify packet in ip tunnels')
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2016-09-27

This series contains updates to igb and igbvf.

Wei Yongjun makes a function static to shut up sparse.

Todd bumps the igb and igbvf version, which is long overdue.

Jake fixes an issue where the PPS SYS_WRAP interrupt was not re-enabled
after a reset, which resulted in disabling of the PPS signaling.

v2: dropped patch 5 of the original series, since the PCI quirk patch
    needs to be reworked by Alex and Sasha to address issues that Bjorn
    Helgaas and Alex Williamson brought up.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

put_cpu_var takes the percpu data, not the data returned from
get_cpu_var.

This doesn't change the behavior.

Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NShaohua Li <shli@fb.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

put_cpu_var takes the percpu data, not the data returned from
get_cpu_var.

This doesn't change the behavior.

Cc: Tejun Heo <tj@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: NShaohua Li <shli@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump igb version to match other igb drivers.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version to match other igbvf drivers.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes the following sparse warning:

drivers/net/ethernet/intel/igb/igb_ethtool.c:2707:5: warning:
 symbol 'igb_rxnfc_write_vlan_prio_filter' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The group list must be freed prior to freeing the command otherwise
we have a use-after-free.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nelson Chang says:

====================
net: ethernet: mediatek: some bug fixes for PDAM and HW LRO

1) Add to stop PDMA while stopping the frame engine
2) Modify the register settings for LRO relinquishments
3) Jump out from the waiting loop while LRO relinquishments are done
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(1) Modify the register settings for LRO relinquishments
(2) Jump out from the waiting loop while LRO relinquishments are done
Signed-off-by: NNelson Chang <nelson.chang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop PDMA while the frame engine is going to stop.
Signed-off-by: NNelson Chang <nelson.chang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Philippe Reynes says:

====================
net: bcmgenet: only use new api ethtool_{get|set}_link_ksettings

Some times ago, a serie of patches were committed :
- commit 62469c76 ("net: ethernet: bcmgenet: use phydev from struct net_device")
- commit 6b352ebc ("net: ethernet: broadcom: bcmgenet: use new api ethtool_{get|set}_link_ksettings")
The first patch add a regression on this driver, so it should be reverted.
As the second patch depend on the former, it should be reverted too.

The first patch is buggy because there is a "trick" in this driver.
The structure phydev is kept in the private data when the interface
go down, and used when the interface go up to enable the phy before
the function phy_connect is called.

I don't have this hardware, neither the datasheet. So I won't
update the driver to avoid this trick.

But the real goal of the first serie was to move to the new api
ethtool_{get|set}_link_ksettings. So I provide a new version of
the patch without the "cleaning" of driver to use the phydev
store in the net_device structure.

Changelog:
v3:
- use priv instead of dev (so all the code use the same phydev)
v2:
- use Florian Fainelli patches for the revert instead of Jaedon Shin
- simply use net: bcmgenet: for the prefix of the patch
====================
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 6b352ebc ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").

We needs to revert the commit 62469c76 ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebc ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This prevent future potential pointer leaks when an unprivileged eBPF
program will read a pointer value from its context. Even if
is_valid_access() returns a pointer type, the eBPF verifier replace it
with UNKNOWN_VALUE. The register value that contains a kernel address is
then allowed to leak. Moreover, this fix allows unprivileged eBPF
programs to use functions with (legitimate) pointer arguments.

Not an issue currently since reg_type is only set for PTR_TO_PACKET or
PTR_TO_PACKET_END in XDP and TC programs that can only be loaded as
privileged. For now, the only unprivileged eBPF program allowed is for
socket filtering and all the types from its context are UNKNOWN_VALUE.
However, this fix is important for future unprivileged eBPF programs
which could use pointers in their context.
Signed-off-by: NMickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

seccomp_phase1() does not exist anymore. Instead, update sample to use
__seccomp_filter(). While at it, set max locked memory to unlimited.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These samples fail to compile as 'struct flow_keys' conflicts with
definition in net/flow_dissector.h. Fix the same by renaming the
structure used in the sample.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jason Baron says:

====================
bnx2x: page allocation failure

While configuring ~500 multicast addrs, we ran into high order
page allocation failures. They don't need to be high order, and
thus I'm proposing to split them into at most PAGE_SIZE allocations.

Below is a sample failure.

[1201902.617882] bnx2x: [bnx2x_set_mc_list:12374(eth0)]Failed to create multicast MACs list: -12
[1207325.695021] kworker/1:0: page allocation failure: order:2, mode:0xc020
[1207325.702059] CPU: 1 PID: 15805 Comm: kworker/1:0 Tainted: G        W
[1207325.712940] Hardware name: SYNNEX CORPORATION 1x8-X4i SSD 10GE/S5512LE, BIOS V8.810 05/16/2013
[1207325.722284] Workqueue: events bnx2x_sp_rtnl_task [bnx2x]
[1207325.728206]  0000000000000000 ffff88012d873a78 ffffffff8267f7c7 000000000000c020
[1207325.736754]  0000000000000000 ffff88012d873b08 ffffffff8212f8e0 fffffffc00000003
[1207325.745301]  ffff88041ffecd80 ffff880400000030 0000000000000002 0000c0206800da13
[1207325.753846] Call Trace:
[1207325.756789]  [<ffffffff8267f7c7>] dump_stack+0x4d/0x63
[1207325.762426]  [<ffffffff8212f8e0>] warn_alloc_failed+0xe0/0x130
[1207325.768756]  [<ffffffff8213c898>] ? wakeup_kswapd+0x48/0x140
[1207325.774914]  [<ffffffff82132afc>] __alloc_pages_nodemask+0x2bc/0x970
[1207325.781761]  [<ffffffff82173691>] alloc_pages_current+0x91/0x100
[1207325.788260]  [<ffffffff8212fa1e>] alloc_kmem_pages+0xe/0x10
[1207325.794329]  [<ffffffff8214c9c8>] kmalloc_order+0x18/0x50
[1207325.800227]  [<ffffffff8214ca26>] kmalloc_order_trace+0x26/0xb0
[1207325.806642]  [<ffffffff82451c68>] ? _xfer_secondary_pool+0xa8/0x1a0
[1207325.813404]  [<ffffffff8217cfda>] __kmalloc+0x19a/0x1b0
[1207325.819142]  [<ffffffffa02fe975>] bnx2x_set_rx_mode_inner+0x3d5/0x590 [bnx2x]
[1207325.827000]  [<ffffffffa02ff52d>] bnx2x_sp_rtnl_task+0x28d/0x760 [bnx2x]
[1207325.834197]  [<ffffffff820695d4>] process_one_work+0x134/0x3c0
[1207325.840522]  [<ffffffff82069981>] worker_thread+0x121/0x460
[1207325.846585]  [<ffffffff82069860>] ? process_one_work+0x3c0/0x3c0
[1207325.853089]  [<ffffffff8206f039>] kthread+0xc9/0xe0
[1207325.858459]  [<ffffffff82070000>] ? notify_die+0x10/0x40
[1207325.864263]  [<ffffffff8206ef70>] ? kthread_create_on_node+0x180/0x180
[1207325.871288]  [<ffffffff826852d2>] ret_from_fork+0x42/0x70
[1207325.877183]  [<ffffffff8206ef70>] ? kthread_create_on_node+0x180/0x180

v2:
 -make use of list_next_entry()
 -only use PAGE_SIZE allocations
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.

For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.

Convert the allocation for the pending list to be done in PAGE_SIZE
increments.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.

For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.

Convert the allocation for 'mcast_list' to be done in PAGE_SIZE
increments.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I stumbled over a new warning during randconfig testing,
with CONFIG_BPF_SYSCALL disabled:

drivers/net/ethernet/netronome/nfp/nfp_net_offload.c: In function 'nfp_net_bpf_offload':
drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: '*((void *)&res+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: 'res.n_instr' may be used uninitialized in this function [-Werror=maybe-uninitialized]

As far as I can tell, this is a false positive caused by the compiler
getting confused about a function that is partially inlined, but it's
easy to avoid while improving the code:

The nfp_bpf_jit() stub helper for that configuration is unusual as it
is defined in a header file but not marked 'static inline'. By moving
the compile-time check into the caller using the IS_ENABLED() macro,
we can remove that stub and simplify the nfp_net_bpf_offload_prepare()
function enough to unconfuse the compiler.

Fixes: 7533fdc0 ("nfp: bpf: add hardware bpf offload")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:2763:5: warning: no previous prototype for 'bcmgenet_hfb_add_filter' [-Wmissing-prototypes]

In fact, this function is implemented in
drivers/net/ethernet/broadcom/genet/bcmgenet.c, but be called
by no one, thus can be removed.

So this patch removes the unused functions.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 10 warnings when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:304:5: warning: no previous prototype for 'cxgb4_dcb_enabled' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:194:5: warning: no previous prototype for 'setup_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:241:6: warning: no previous prototype for 'free_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:268:5: warning: no previous prototype for 'cfg_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:344:6: warning: no previous prototype for 'free_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:353:5: warning: no previous prototype for 'request_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:379:6: warning: no previous prototype for 'free_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:393:6: warning: no previous prototype for 'name_msix_vecs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:433:6: warning: no previous prototype for 'enable_rx_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:442:6: warning: no previous prototype for 'quiesce_rx_uld' [-Wmissing-prototypes]

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/marvell/mvneta.c:639:27: warning: no previous prototype for 'mvneta_get_stats64' [-Wmissing-prototypes]
drivers/net/ethernet/marvell/mvneta.c:3529:5: warning: no previous prototype for 'mvneta_ethtool_set_link_ksettings' [-Wmissing-prototypes]

In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/hisilicon/hip04_eth.c:603:22: warning: no previous prototype for 'tx_done' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/hisilicon/hisi_femac.c:943:5: warning: no previous prototype for 'hisi_femac_drv_suspend' [-Wmissing-prototypes]
drivers/net/ethernet/hisilicon/hisi_femac.c:960:5: warning: no previous prototype for 'hisi_femac_drv_resume' [-Wmissing-prototypes]

In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2016-09-25

Here are a few more Bluetooth & 802.15.4 patches for the 4.9 kernel that
have popped up during the past week:

 - New USB ID for QCA_ROME Bluetooth device
 - NULL pointer dereference fix for Bluetooth mgmt sockets
 - Fixes for BCSP driver
 - Fix for updating LE scan response

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

drivers/net/dsa/mv88e6xxx/chip.c:219:5: warning:
 symbol 'mv88e6xxx_port_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx/chip.c:227:5: warning:
 symbol 'mv88e6xxx_port_write' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

drivers/net/ethernet/emulex/benet/be_main.c:47:25: warning:
 symbol 'be_err_recovery_workq' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:63:25: warning:
 symbol 'be_wq' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This aligns smc91x with its cousin, namely smc911x.c.
This also allows the driver to run also in a device-tree based lubbock
board build, on which it was tested.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iq is unsigned, so the error check for iq < 0 has no effect so errors
can slip past this check.  Fix this by making iq signed and also
get_filter_steerq return a signed int so a -ve error can be returned.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for your net-next
tree, they are:

1) Consolidate GRE protocol tracker using new GRE protocol definitions,
   patches from Gao Feng.

2) Properly parse continuation lines in SIP helper, update allowed
   characters in Call-ID header and allow tabs in SIP headers as
   specified by RFC3261, from Marco Angaroni.

3) Remove useless code in FTP conntrack helper, also from Gao Feng.

4) Add number generation expression for nf_tables, with random and
   incremental generators. This also includes specific offset to add
   to the result, patches from Laura Garcia Liebana. Liping Zhang
   follows with a fix to avoid a race in this new expression.

5) Fix new quota expression inversion logic, added in the previous
   pull request.

6) Missing validation of queue configuration in nft_queue, patch
   from Liping Zhang.

7) Remove unused ctl_table_path, as part of the deprecation of the
   ip_conntrack sysctl interface coming in the previous batch.
   Again from Liping Zhang.

8) Add offset attribute to nft_hash expression, so we can generate
   any output from a specific base offset. Moreover, check for
   possible overflow, patches from Laura Garcia.

9) Allow to invert dynamic set insertion from packet path, to check
   for overflows in case the set is full.

10) Revisit nft_set_pktinfo*() logic from nf_tables to ensure
    proper initialization of layer 4 protocol. Consolidate pktinfo
    structure initialization for bridge and netdev families.

11) Do not inconditionally drop IPv6 packets that we cannot parse
    transport protocol for ip6 and inet families, let the user decide
    on this via ruleset policy.

12) Get rid of gotos in __nf_ct_try_assign_helper().

13) Check for return value in register_netdevice_notifier() and
    nft_register_chain_type(), patches from Gao Feng.

14) Get rid of CONFIG_IP6_NF_IPTABLES dependency in nf_queue
    infrastructure that is common to nf_tables, from Liping Zhang.

15) Disable 'found' and 'searched' stats that are updates from the
    packet hotpath, not very useful these days.

16) Validate maximum value of u32 netlink attributes in nf_tables,
    this introduces nft_parse_u32_check(). From Laura Garcia.

17) Add missing code to integrate nft_queue with maps, patch from
    Liping Zhang. This also includes missing support ranges in
    nft_queue bridge family.

18) Fix check in nft_payload_fast_eval() that ensure that we don't
    go over the skbuff data boundary, from Liping Zhang.

19) Check if transport protocol is set from nf_tables tracing and
    payload expression. Again from Liping Zhang.

20) Use net_get_random_once() whenever possible, from Gao Feng.

21) Replace hardcoded value by sizeof() in xt_helper, from Gao Feng.

22) Remove superfluous check for found element in nft_lookup.

23) Simplify TCPMSS logic to check for minimum MTU, from Gao Feng.

24) Replace double linked list by single linked list in Netfilter
    core hook infrastructure, patchset from Aaron Conole. This
    includes several patches to prepare this update.

25) Fix wrong sequence adjustment of TCP RST with no ACK, from
    Gao Feng.

26) Relax check for direction attribute in nft_ct for layer 3 and 4
    protocol fields, from Liping Zhang.

27) Add new revision for hashlimit to support higher pps of upto 1
    million, from Vishwanath Pai.

28) Evict stale entries in nf_conntrack when reading entries from
    /proc/net/nf_conntrack, from Florian Westphal.

29) Fix transparent match for IPv6 request sockets, from Krisztian
    Kovacs.

30) Add new range expression for nf_tables.

31) Add missing code to support for flags in nft_log. Expose NF_LOG_*
    flags via uapi and use it from the generic logging infrastructure,
    instead of using xt specific definitions, from Liping Zhang.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/netfilter/core.c
	net/netfilter/nf_tables_netdev.c

Resolve two conflicts before pull request for David's net-next tree:

1) Between c73c2484 ("netfilter: nf_tables_netdev: remove redundant
   ip_hdr assignment") from the net tree and commit ddc8b602
   ("netfilter: introduce nft_set_pktinfo_{ipv4, ipv6}_validate()").

2) Between e8bffe0c ("net: Add _nf_(un)register_hooks symbols") and
   Aaron Conole's patches to replace list_head with single linked list.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

nf_log is used by both nftables and iptables, so use XT_LOG_XXX macros
here is not appropriate. Replace them with NF_LOG_XXX.
Signed-off-by: NLiping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>