proc_net_fops_create has been replaced by proc_create,
we can remove it now.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.

It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPDMA interrupts are not properly acknowledged which leads to interrupt
storm, only cpdma interrupt 0 is acknowledged in Davinci CPDMA driver.
Changed cpdma_ctlr_eoi api to acknowledge 1 and 2 interrupts which are
used for rx and tx respectively.
Reported-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upper case macros for various chip attributes are slightly
difficult to read and are a bit out of characterto the other
tg3_<foo> attribute functions.

Convert:

GET_ASIC_REV(tp->pci_chip_rev_id)       -> tg3_asic_rev(tp)
GET_CHIP_REV(tp->pci_chip_rev_id)       -> tg3_chip_rev(tp)

Remove:
GET_METAL_REV(tp->pci_chip_rev_id)      -> tg3_metal_rev(tp) (unused)

Add:
tg3_chip_rev_id(tp) for tp->pci_chip_rev_id so access styles
are similar to tg3_asic_rev and tg3_chip_rev.

These macros are not converted to static inline functions
because gcc (tested with 4.7.2) is currently unable to
optimize the object code it produces the same way and code
is otherwise larger.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's the same value as tp->pci_chip_rev_id so use that
instead.  This makes all CHIPREV_ID_<foo> tests the same.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch I get many unaligned access warnings per packet,
this patches fixes them all. This should improve performance on some
systems like mips.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same problem as IPv6
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Should not use assignment in conditional:
 warning: suggest parentheses around assignment used as truth value [-Wparentheses]

Problem introduced by:
commit 14bbd6a5
Author: Pravin B Shelar <pshelar@nicira.com>
Date:   Thu Feb 14 09:44:49 2013 +0000

    net: Add skb_unclone() helper function.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e1000, e1000e, igb, igbvf and ixgbe.
The e1000, e1000e, igb and igbvf are single patch changes and the
remaining 11 patches are all against ixgbe.

The e1000 patch is a comment cleanup to align e1000 with the code
commenting style for /drivers/net.  It also contains a few other white
space cleanups (i.e. fix lines over 80 char, remove unnecessary blank
lines and fix the use of tabs/spaces).

The e1000e patch from Koki (Fujitsu) adds a warning when link speed is
downgraded due to SmartSpeed.

The igb patch from Stefan (Red Hat) increases the timeout in the ethtool
offline self-test because some i350 adapters would sometimes fail the
self-test because link auto negotiation may take longer than the current
4 second timeout.

The igbvf patch from Alex is meant to address several race issues that
become possible because next_to_watch could possibly be set to a value
that shows that the descriptor is done when it is not.  In order to correct
that we instead make next_to_watch a pointer that is set to NULL during
cleanup, and set to the eop_desc after the descriptor rings have been written.

The remaining patches for ixgbe are a mix of fixes and added support as well
as some cleanup.  Most notably is the added support for displaying the
number of Tx/Rx channels via ethtool by Alex.  Also Aurélien adds the
ability for reading data from SFP+ modules over i2c for diagnostic
monitoring.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They well deserve a separated unit.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ehea.h the minimal entries is 2^7 - 1:
#define EHEA_MIN_ENTRIES_QP  127

Thus change the module param description accordinglly
Signed-off-by: NDave Young <dyoung@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ipv6_addr_hash() and a single jhash invocation.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Paul Gortmaker says:

====================
Two relatively small cleanup patches here, plus a reimplementation
of the patch Neil had questions about[1] in the last development
cycle.

Tested on today's net-next, between 32 and 64 bit x86 machines using
the server/client in tipc-utils, as usual.

[1] http://patchwork.ozlabs.org/patch/204507/
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes have made it so that MAX_SKB_FRAGS is now never less than 16.
As a result we were seeing issues on systems with 64K pages as it would
cause DESC_NEEDED to increase to 68, and we would need over 136 descriptors
free before clean_tx_irq would wake the queue.

This patch makes it so that DESC_NEEDED is always MAX_SKB_FRAGS + 4.  This
should prevent any possible deadlocks on the systems with 64K pages as we will
now only require 42 descriptors to wake.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes sure that TXDCTL.WTHRESH is set to 1 when BQL is enabled
and EITR is set to more than 100k interrupts per second to avoid Tx timeouts.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for reading data from SFP+ modules over i2c.
Signed-off-by: NAurélien Guillaume <footplus@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces instances where a return code from i2c operations
were checked against a list of error codes with a much simpler
if ( status != 0 ) check.

Some whitespace cleanups included.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes sure that the SW lock is released after all i2c
operations complete in the retry code path.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for the ethtool set_channels operation.

Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the ethtool get_channels operation.

Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe_setup_tc code is essentially the same code we need any time we have
to update the number of queues.  As such I am making it available always and
just stripping the DCB specific bits out when DCB is disabled instead of
stripping the entire function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue.  The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for ixgbe to configure the XPS queue mapping on
load.  The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner.  This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.

I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs.  This essentially treats the two
groupings like they are two separate traffic classes.

In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.

I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64.  The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On several machines with i350 adapters the ethtool offline self-test sometimes
fails. This happens because link auto negotiation may take longer than the
timeout of 4 seconds. Increasing the timeout by 1 seconds resolves the issue.

Output from a failing i350 offline self-test:
while [ 1 ]; do ethtool -t eth2 offline; done
The test result is PASS
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         0

The test result is FAIL
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         1

The test result is PASS
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         0
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to address several race issues that become possible
because next_to_watch could possibly be set to a value that shows that the
descriptor is done when it is not.  In order to correct that we instead make
next_to_watch a pointer that is set to NULL during cleanup, and set to the
eop_desc after the descriptor rings have been written.

To enforce proper ordering the next_to_watch pointer is not set until after
a wmb writing the values to the last descriptor in a transmit.  In order to
guarantee that the descriptor is not read until after the eop_desc we use the
read_barrier_depends which is only really necessary on the alpha architecture.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed.  As a result, users suspect that there is something wrong with
NIC.  If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: NKoki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed.  In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

As the number of iovecs in a send request is already limited within
UIO_MAXIOV(i.e. 1024) in __sys_sendmsg(), it's unnecessary to check it
again in TIPC stack.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Change overload control to be purely byte-based, using
sk->sk_rmem_alloc as byte counter, and compare it to a calculated
upper limit for the socket receive queue.

For all connection messages, irrespective of message importance,
the overload limit is set to a constant value (i.e, 67MB). This
limit should normally never be reached because of the lower
limit used by the flow control algorithm, and is there only
as a last resort in case a faulty peer doesn't respect the send
window limit.

For datagram messages, message importance is taken into account
when calculating the overload limit. The calculation is based
on sk->sk_rcvbuf, and is hence configurable via the socket option
SO_RCVBUF.

Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The tipc function discard_rx_queue() is just a duplicated
implementation of __skb_queue_purge().  Remove the former
and directly invoke __skb_queue_purge().

In doing so, the underscores convey to the code reader, more
information about the current locking state that is assumed.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We no longer need to use mac_len, lets cleanup things.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to igb and ixgbe.  Most of the changes
are against igb, except for one patch against ixgbe.

There are 3 igb fixes from Carolyn which were reported by Dan
Carpenter which resolve issues found in the get_i2c_client().  Alex
does some cleanup of the igb driver to match similar functionality
in ixgbe on transmit.  Alex also makes it so that we can enable the use
of build_skb for cases where jumbo frames are disabled.  The advantage
to this is that we do not have to perform a memcpy to populate the header
and as a result we see a significant performance improvement.

Akeem provides 4 patches to initialize function pointers and do a
re-factoring of the function pointers in igb_get_variants() to assist
with driver debugging.

The ixgbe patch comes from Emil to reshuffle the switch/case structure
of the flag assignment to allow for the flags to be set for each MAC
type separately. This is needed for new hardware that does not have feature
parity with older hardware.

v2: updated patches 4 & 5 based on feedback from Ben Hutchings and Eric
    Dumazet
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.

[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function will be used in next GRE_GSO patch. This patch does
not change any functionality. It only exports skb_mac_gso_segment()
function.

[ Use skb_reset_mac_len() -DaveM ]
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function will be used in next GRE_GSO patch. This patch does
not change any functionality.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NEric Dumazet <edumazet@google.com>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before the device is opened, the carrier state should be off.  It
will not race with the link interrupt if we set it before calling
register_netdev().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't set the default size to 128K if it is 5762.  Instead, rely on the
size we obtain from NVRAM location 0xf0.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>