Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code.  Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The NVMUpdate tool doesn't necessarily know the ReadOnly map of the current
NVM image, and must try reading and writing words that may be protected.
This generates an error out of the Firmware request that the driver logs.
Unfortunately, this ends up spitting out hundreds of bogus read and write
error message that looks rather messy.

This patch checks the error type and under normal conditions will not print
the typical read and write errors during NVMUpdate.  This can be overridden
by enabling the NVM update debugging.  This results in a much less messy log
file, and likely many fewer customer support questions.

Change-ID: Id4ff2e9048c523b0ff503aa5ab181b025ec948ea
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.

The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.

Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.

Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.

Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the sizeof() calls are taking the size of the actual struct
that we care about.  By using the pointer variable, we'll always get
the right struct size, even if the variable type changes sometime in
the future.

Change-ID: Id5858f883cf42447365ea3733080d7714f975bce
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While using the Linux "strings" command I found these two strings in the
driver.  There's no need for them and they're kinda silly.

Change-ID: I4e19b02983d48b631e9a9979f49790492845f221
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of configfs is not allowed in network drivers.  Strip the code that
uses it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.12 and i40evf to 1.2.6.

Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.

Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.

Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use l4_tunnel type generically to keep code flow simple.

Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.

If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.

If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.

ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.

Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.

Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only print the port and veb stats if this is the first partition
of a multiplexed port.

Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.

Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition.  This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny.  Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.

Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.

Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.

This fixes the sparse warning and fixes up the other issues.

Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16.  Fix the width of the datatype.

Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.

Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This series of code was repeated twice, remove one of them.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.

Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.

Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:

Changing MTU frees all the rx buffers:
    e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
        e1000_clean_rx_ring

Then, close to the end of e1000_change_mtu:
    pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
        e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag

And when we come back to do the rest of the MTU change:
    e1000_up -> e1000_configure -> e1000_configure_rx ->
        e1000_alloc_jumbo_rx_buffers

alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.

This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330

    [...]

Call Trace:
 [<ffffffff81195445>] put_page+0x55/0x60
 [<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
 [<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
 [<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
 [<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
 [<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
 [<ffffffff81647050>] dev_set_mtu+0xa0/0x140
 [<ffffffff81664218>] do_setlink+0x218/0xac0
 [<ffffffff814459e9>] ? nla_parse+0xb9/0x120
 [<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
 [<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
 [<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
 [<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260

By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers.  The allocator is set back to a sane value in
e1000_configure_rx.

Fixes: edbbb3ca ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.

Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.

Move netif_carrier_off as early as possible.
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While addressing the pin problem I noticed that all of the pin register
values where having to be pushed onto the stack each time the function was
called.  To avoid that I am making them static const so that they should
only need to be allocated once and we can avoid all the instructions to get
them onto the stack..

size before:
   text	   data	    bss	    dec	    hex	filename
 161477	  10512	      8	 171997	  29fdd	drivers/net/ethernet/intel/igb/igb.ko

size after:
   text	   data	    bss	    dec	    hex	filename
 161205	  10512	      8	 171725	  29ecd	drivers/net/ethernet/intel/igb/igb.ko
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When building the kernel using the gcc 4.8.3 compiler included in Fedora 20
I was repeatedly seeing the warning:

 drivers/net/ethernet/intel/igb/igb_ptp.c: In function ‘igb_ptp_feature_enable_i210’:
 drivers/net/ethernet/intel/igb/igb_ptp.c:395:21: warning: ‘pin’ may be used uninitialized in this function
 [-Wmaybe-uninitialized]
   tssdp &= ~ts_sdp_en[pin];
                     ^
 drivers/net/ethernet/intel/igb/igb_ptp.c:471:6: note: ‘pin’ was declared here
   int pin;
       ^

To resolve it I am assigning the pin a value of -1 when it is instantiated.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar.  The mapping/unmapping is relevant
to older HW only.

CC: John W Linville <linville@tuxdriver.com>
Reported-by: NJohn W Linville <linville@tuxdriver.com>
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The interface to the device flash was modified in i219 and later HW.
This patch better describes the change and the impact on the driver.

CC: John W Linville <linville@tuxdriver.com>
Reported-by: NJohn W Linville <linville@tuxdriver.com>
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump i40e to 1.2.11 and i40evf to 1.2.5

Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver spams the system log with messages about VF VSI when VFs
are created, as well as each time they are reset. This is annoying, and
the information isn't even useful most of the time.

Remove this message to reduce user annoyance.

Change-ID: I8de90d05380f54b038c9c8c3265150be87c9242c
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown.  This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.

Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.

Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.

Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.

Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the 10G and 40G AOC PHY types to the case statement in get_media_type
and ethtool get_settings so that the correct information gets reported
back to the user.

Change-ID: I1b4849d22199a9acf7c8807166d0317c1faad375
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the system administrator is requesting an offline diagnostic test using
'ethtool -t' then we should, you know, actually take the device offline
before doing the testing.

Change-ID: I6afa1cbfcc821c9ab6e6f47ed4d8dc2d8dd20e82
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some FW versions are incorrectly reporting a breakout cable as PHY type
0x3 when it should be 0x16 (I40E_PHY_TYPE_10GBASE_SFPP_CU).
If we get this value back from FW and the version is < 4.40, reassign it
to I40E_PHY_TYPE_10GBASE_SFPP_CU.

Change-ID: Ibb41a0e3cd2c0753744e8553959240df6ed13ae8
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.

This caused higher CPU utilization and had some other performance impacts
for transmit tests.

Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use automatic sign extension by replacing 0xffff... constants
with ~(u64)0 or ~(u32)0.

Change-ID: I73cab4cd2611795bb12e00f0f24fafaaee07457c
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.

Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>