kbuild reported:

rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]

Fix it by adding temporary ifdefs around the static functions.

Fixes: 033695bd ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When reading external NVM file, if a section exists both in OTP
and in the external file, the memory that was allocated at OTP
reading is not freed.
This is possible only on systems that have an external NVM
file which is typically the case on embedded systems.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_disable_queue function requires the TID to be set to
IWL_MAX_TID_COUNT when disabling an AC queue. Call it correctly for TDLS
scenarios.

Fixes: 4ecafae9 ("iwlwifi: mvm: support using multiple ACs on single HW queue")
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases, scan reference was taken, but wasn't
released even though scan command wasn't actually issued.

Change the current code to simply take the reference
only on success.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As cfg80211 already enforces these limits, there's little point
in having them again here in our code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement config_iface_filter() driver op. Currently support only
probe request registration for p2p client vifs, by setting
MAC_FILTER_IN_PROBE_REQUEST flag in MAC_CONTEXT_CMD.
This is needed since WFDS spec and certification require a P2P client
to be discoverable on its operating channel.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Recovery takes too much time if the bus is dead (each timeout
is 2000ms, etc.).
Explicitly skip fw dump in this case, as it will result in
garbage data (and might take signifcant time)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for two scan plans for scheduled scan. The first plan
will run for a limited number of iterations, then the second plan
will run infinitely.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of only allowing the caller to decide whether the CMD_ASYNC
flag is set, let it pass the entire flags bitmask.  This allows more
flexibility and will be needed when we call this function in the
suspend flow (where other flags are needed).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch enables the debugfs user to configure an FTM responder
with the appropriate control channel position.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Those timeouts are used for AM-to-PSM transition.
We already have those pairs defined for default and WOWLAN use cases.
We expect that by using shorter threshold for low latency P2P,
e.g. for Miracast video scenario, we might save a considerable amount of power.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In "hostless" mode (D3 or D0i3) the same parameters were intended
to be used, but the code doesn't do that properly. Fix it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the 8000 series, the DTS measurement request command has been
changed. Use an ucode capability flag to determine which version is
supported and send the extended command when needed.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The hardware bug in the commit mentioned below forces us
not to re-enable the clock gating in the Host Cluster.
The impact on the power consumption is minimal and it allows
the WAKE_ME interrupt to propagate.

CC: <stable@vger.kernel.org> [4.1+]
Fixes: c9fdec9f ("iwlwifi: pcie: fix prepare card flow")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When paging is enabled the driver stores part of the FW's
image in the DRAM.

Dump FW's virtual image in the case of a NIC error.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove an old workaround that's no longer needed and
enable MIMO on P2P interfaces.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are still four devices which are currently supported both by the new
rtl8xxxu driver and rtlwifi. To not break existing setups enable the support
for these four devices only when CONFIG_RTL8XXXU_UNTESTED is turned on.

Once rtl8xxxu support is found to be good enough the devices can be removed
from rtlwifi and enabled by default in rtl8xxxu.
Reported-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is a new Broadcom chip and we should be able to recognize it.
Signed-off-by: NEric Caruso <ejcaruso@google.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the netif_carrier api to correctly set carrier state on the
different modes.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With this feature it becomes possible to request a station
assoc list.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Txrate and rxrate in get_station got assigned first with value
in kbps and then divided by 100 to get it in 100kbps unit. The
problem with that is that type of rate is u16 which resulted
in incorrect values for high data rate values.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When module param p2pon is used a p2p device is created at init.
This patch reworks how this is done by using the same method as
for a dynamically (by user space) created p2p device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Removing a comment that was only useful during the review of
the change that introduced it and which should never have been
submitted.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In brcmfmac the module parameter "firmware_path" is used as an
alternative relative path under the search path used by firmware_class
or ueventhelper. Rename the parameter to alternative_fw_path to avoid
confusion.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When a USB device gets disconnected due to for example removal
then it is possible that it is still in the loading phase due to
the asynchronous load routines. These routines can then possible
access memory which has been freed. Fix this by mutex locking the
device init phase.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Upon PSM watchdog event received from firmware the driver will obtain
a memory snapshot of the device and expose it to user-space through
the devcoredump framework. This will trigger a uevent.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is an alternate driver for a number of Realtek WiFi USB devices,
including RTL8723AU, RTL8188CU, RTL8188RU, RTL8191CU, and RTL8192CU.
It was written from scratch utilizing the Linux mac80211 stack.

After spending months cleaning up the vendor provided rtl8723au
driver, which comes with it's own 802.11 stack included, I decided to
rewrite this driver from the bottom up.

Many thanks to Johannes Berg for 802.11 insights and help and Larry
Finger for help with the vendor driver.

The full git log for the development of this driver can be found here:
git git://git.kernel.org/pub/scm/linux/kernel/git/jes/linux.git
    branch rtl8723au-mac80211

This driver is still under development, but has proven to be very
stable for me. It currently supports station mode only. It has support
for OFDM and CCK rates. It does lack certain features found in the
staging driver, such as power management, AMPDU, and 40MHz channel
support. In addition it does not support AD-HOC, AP, and monitor mode
support at this point.

The driver is known to work with the following devices:
Lenovo Yoga (rtl8723au)
TP-Link TL-WN823N (rtl8192cu)
Etekcity 6R (rtl8188cu)
Daffodil LAN03 (rtl8188cu)
Alfa AWUS036NHR (rtl8188ru)
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NTamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch disables PCI PS for QCA988X and QCA99X0, Since PCI PS is
validated for QCA6174, let it be enabled only for QCA6174. It would be
better to execute PCI PS related functions only for the supported devices.

PCI time out issue is observed with QCA99X0 on x86 platform, We will
disable PCI PS for QCA988X and QCA99X0 until PCI PS is properly implemented.

Taking and releasing ps_lock is causing higher CPU consumption. Michal Kazior
suggested ps_lock overhead to be reworked so that ath10k_pci_wake/sleep
functions are called less often, i.e. move the powersave logic up (only during
irq handling, tx path, submitting fw commands) but that's a bigger change and
can be implemented later.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since polling for tx completion is handled whenever target to host
messages are received, removing the unnecessary polling mechanism for
send completion at HTC level.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since polling for received messages not supported, remove unused
dl_is_polled.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently target to host (T2H) HTT messages are received at copy engine 1.
These messages are processed by HTC layer in both host and target.
To avoid HTC level processing overhead in both host and target,
the unused copy engine 5 is being used for receiving HTT T2H messages.
This will speedup the receive data processing as well as htt tx completion.
Hence host and target copy engine configuration tables are updated
to enable CE5 pipe. The in-direction HTT mapping is now pointing to CE5
for all HTT T2H.

Moreover HTT send completion messages are polled from HTC handler
as CE 4 is not interrupt-driven. For faster tx completion, CE4 polling
needs to be done whenever CE pipe which transports HTT Rx (target->host)
is processed. This avoids overhead of polling HTT messages from HTC
layer. Servicing CE 4 faster is helping to solve "failed to transmit
packet, dropping: -105".
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some special copy engines delivers messages directly to HTT by
bypassing HTC layer. Hence exporting tx_completion and rx_handler
for delivering the data to HTT layer.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Register receive callbacks for every copy engines (CE) separately
instead of having common receive handler. Some of the copy engines
receives different type of messages (i.e HTT/HTC/pktlog) from target.
Hence to service them accordingly, register per copy engine receive
callbacks.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Register send completion callbacks for every copy engines (CE) separately
instead of having common completion handler. Since some of the copy
engines delivers different type of messages, per-CE callbacks help to
service them differently.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Export HTC layer tx and rx handlers. This will be used by HIF layer
for per-CE data processing. Instead of callback mechanism, HIF will
call appropriate upper layers API directly.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>