This reformats and properly indents sys_ptrace (only whitespace changes).
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The timers lack .suspend/.resume methods.  Because of this, jiffies got a
big compensation after a S3 resume.  And then softlockup watchdog reports
an oops.  This occured with HPET enabled, but it's also possible for other
timers.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean code up a bit, and only show suspend to disk as available when
it is configured in.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If process freezing fails, some processes are frozen, and rest are left in
"were asked to be frozen" state.  Thats wrong, we should leave it in some
consistent state.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Drop printing during normal boot (when no image exists in swap), print
message when drivers fail, fix error paths and consolidate near-identical
functions in disk.c (and functions with just one statement).
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It is trying to protect swsusp_resume_device and software_resume() from two
users banging it from userspace at the same time.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The attached patch contains a mini howto for using dm-crypt together with
swsusp.
Signed-off-by: NAndreas Steinmetz <ast@domdv.de>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The function calc_nr uses an iterative algorithm to calculate the number of
pages needed for the image and the pagedir.  Exactly the same result can be
obtained with a one-line expression.

Note that this was even proved correct ;-).
Signed-off-by: NMichal Schmidt <xschmi00@stud.feec.vutbr.cz>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Stop the disks from spinning down and up on suspend.
Signed-off-by: NMichal Schmidt <xschmi00@stud.feec.vutbr.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch protects from leaking sensitive data after resume from suspend.
During suspend a temporary key is created and this key is used to encrypt the
data written to disk.  When, during resume, the data was read back into memory
the temporary key is destroyed which simply means that all data written to
disk during suspend are then inaccessible so they can't be stolen lateron.

Think of the following: you suspend while an application is running that keeps
sensitive data in memory.  The application itself prevents the data from being
swapped out.  Suspend, however, must write these data to swap to be able to
resume lateron.  Without suspend encryption your sensitive data are then
stored in plaintext on disk.  This means that after resume your sensitive data
are accessible to all applications having direct access to the swap device
which was used for suspend.  If you don't need swap after resume these data
can remain on disk virtually forever.  Thus it can happen that your system
gets broken in weeks later and sensitive data which you thought were encrypted
and protected are retrieved and stolen from the swap device.
Signed-off-by: NAndreas Steinmetz <ast@domdv.de>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This should bits from -mm tree that are affected by pm_message_t
conversion.  [I'm not 100% sure I got all of them, but I certainly got all
the errors on make allyesconfig build, and most of warnings, too.  I'll go
through the buildlog tommorow and fix any remaining bits].
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32.  It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).

[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAlexander Nyberg <alexn@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix remaining bits of u32 vs.  pm_message confusion.  Should not break
anything.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update suspend documentation.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reset the ISA DMA controller into a known state after a suspend.  Primary
concern was reenabling the cascading DMA channel (4).
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reset the ISA DMA controller into a known state after a suspend.  Primary
concern was reenabling the cascading DMA channel (4).
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This should make refrigerator sleep properly, not busywait after the first
schedule() returns.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch moves the common code in x86 and x86-64's semaphore.c into a
single file in lib/semaphore-sleepers.c.  The arch specific asm stubs are
left in the arch tree (in semaphore.c for i386 and in the asm for x86-64).
There should be no changes in code/functionality with this patch.
Signed-off-by: NBenjamin LaHaise <benjamin.c.lahaise@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

for_each_cpu walks through all processors in cpu_possible_map, which is
defined as cpu_callout_map on i386 and isn't initialised until all
processors have been booted. This breaks things which do for_each_cpu
iterations early during boot. So, define cpu_possible_map as a bitmap with
NR_CPUS bits populated. This was triggered by a patch i'm working on which
does alloc_percpu before bringing up secondary processors.

From: Alexander Nyberg <alexn@telia.com>

i386-boottime-for_each_cpu-broken.patch
i386-boottime-for_each_cpu-broken-fix.patch

The SMP version of __alloc_percpu checks the cpu_possible_map before
allocating memory for a certain cpu.  With the above patches the BSP cpuid
is never set in cpu_possible_map which breaks CONFIG_SMP on uniprocessor
machines (as soon as someone tries to dereference something allocated via
__alloc_percpu, which in fact is never allocated since the cpu is not set
in cpu_possible_map).
Signed-off-by: NZwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: NAlexander Nyberg <alexn@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a clone operation for pgd updates.

This helps complete the encapsulation of updates to page tables (or pages
about to become page tables) into accessor functions rather than using
memcpy() to duplicate them.  This is both generally good for consistency
and also necessary for running in a hypervisor which requires explicit
updates to page table entries.

The new function is:

clone_pgd_range(pgd_t *dst, pgd_t *src, int count);

   dst - pointer to pgd range anwhere on a pgd page
   src - ""
   count - the number of pgds to copy.

   dst and src can be on the same page, but the range must not overlap
   and must not cross a page boundary.

Note that I ommitted using this call to copy pgd entries into the
software suspend page root, since this is not technically a live paging
structure, rather it is used on resume from suspend.  CC'ing Pavel in case
he has any feedback on this.

Thanks to Chris Wright for noticing that this could be more optimal in
PAE compiles by eliminating the memset.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds a notify to the die_nmi notify that the system is about to
be taken down.  If the notify is handled with a NOTIFY_STOP return, the
system is given a new lease on life.

We also change the nmi watchdog to carry on if die_nmi returns.

This give debug code a chance to a) catch watchdog timeouts and b) possibly
allow the system to continue, realizing that the time out may be due to
debugger activities such as single stepping which is usually done with
"other" cpus held.

Signed-off-by: George Anzinger<george@mvista.com>
Cc: Keith Owens <kaos@ocs.com.au>
Signed-off-by: NGeorge Anzinger <george@mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Introduce a write acessor for updating the current LDT.  This is required
for hypervisors like Xen that do not allow LDT pages to be directly
written.

Testing - here's a fun little LDT test that can be trivially modified to
test limits as well.

/*
 * Copyright (c) 2005, Zachary Amsden (zach@vmware.com)
 * This is licensed under the GPL.
 */

#include <stdio.h>
#include <signal.h>
#include <asm/ldt.h>
#include <asm/segment.h>
#include <sys/types.h>
#include <unistd.h>
#include <sys/mman.h>
#define __KERNEL__
#include <asm/page.h>

void main(void)
{
        struct user_desc desc;
        char *code;
        unsigned long long tsc;

        code = (char *)mmap(0, 8192, PROT_EXEC|PROT_READ|PROT_WRITE,
                                 MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
        desc.entry_number = 0;
        desc.base_addr = code;
        desc.limit = 1;
        desc.seg_32bit = 1;
        desc.contents = MODIFY_LDT_CONTENTS_CODE;
        desc.read_exec_only = 0;
        desc.limit_in_pages = 1;
        desc.seg_not_present = 0;
        desc.useable = 1;
        if (modify_ldt(1, &desc, sizeof(desc)) != 0) {
                perror("modify_ldt");
        }
        printf("code base is 0x%08x\n", (unsigned)code);
        code[0x0ffe] = 0x0f;  /* rdtsc */
        code[0x0fff] = 0x31;
        code[0x1000] = 0xcb;  /* lret */
        __asm__ __volatile("lcall $7,$0xffe" : "=A" (tsc));
        printf("TSC is 0x%016llx\n", tsc);
}
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When reviewing GDT updates, I found the code:

	set_tss_desc(cpu,t);	/* This just modifies memory; ... */
        per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TSS].b &= 0xfffffdff;

This second line is unnecessary, since set_tss_desc() has already cleared
the busy bit.

Commented disassembly, line 1:

c028b8bd:       8b 0c 86                mov    (%esi,%eax,4),%ecx
c028b8c0:       01 cb                   add    %ecx,%ebx
c028b8c2:       8d 0c 39                lea    (%ecx,%edi,1),%ecx

  => %ecx = per_cpu(cpu_gdt_table, cpu)

c028b8c5:       8d 91 80 00 00 00       lea    0x80(%ecx),%edx

  => %edx = &per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TSS]

c028b8cb:       66 c7 42 00 73 20       movw   $0x2073,0x0(%edx)
c028b8d1:       66 89 5a 02             mov    %bx,0x2(%edx)
c028b8d5:       c1 cb 10                ror    $0x10,%ebx
c028b8d8:       88 5a 04                mov    %bl,0x4(%edx)
c028b8db:       c6 42 05 89             movb   $0x89,0x5(%edx)

  => ((char *)%edx)[5] = 0x89
  (equivalent) ((char *)per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TSS])[5] = 0x89

c028b8df:       c6 42 06 00             movb   $0x0,0x6(%edx)
c028b8e3:       88 7a 07                mov    %bh,0x7(%edx)
c028b8e6:       c1 cb 10                ror    $0x10,%ebx

  => other bits

Commented disassembly, line 2:

c028b8e9:       8b 14 86                mov    (%esi,%eax,4),%edx
c028b8ec:       8d 04 3a                lea    (%edx,%edi,1),%eax

  => %eax = per_cpu(cpu_gdt_table, cpu)

c028b8ef:       81 a0 84 00 00 00 ff    andl   $0xfffffdff,0x84(%eax)

  => per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TSS].b &= 0xfffffdff;
  (equivalent) ((char *)per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TSS])[5] &= 0xfd

Note that (0x89 & ~0xfd) == 0; i.e, set_tss_desc(cpu,t) has already stored
the type field in the GDT with the busy bit clear.

Eliminating redundant and obscure code is always a good thing; in fact, I
pointed out this same optimization many moons ago in arch/i386/setup.c,
back when it used to be called that.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The pushf/popf in switch_to are ONLY used to switch IOPL.  Making this
explicit in C code is more clear.  This pushf/popf pair was added as a
bugfix for leaking IOPL to unprivileged processes when using
sysenter/sysexit based system calls (sysexit does not restore flags).

When requesting an IOPL change in sys_iopl(), it is just as easy to change
the current flags and the flags in the stack image (in case an IRET is
required), but there is no reason to force an IRET if we came in from the
SYSENTER path.

This change is the minimal solution for supporting a paravirtualized Linux
kernel that allows user processes to run with I/O privilege.  Other
solutions require radical rewrites of part of the low level fault / system
call handling code, or do not fully support sysenter based system calls.

Unfortunately, this added one field to the thread_struct.  But as a bonus,
on P4, the fastest time measured for switch_to() went from 312 to 260
cycles, a win of about 17% in the fast case through this performance
critical path.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Privilege checking cleanup.  Originally, these diffs were much greater, but
recent cleanups in Linux have already done much of the cleanup.  I added
some explanatory comments in places where the reasoning behind certain
tests is rather subtle.

Also, in traps.c, we can skip the user_mode check in handle_BUG().  The
reason is, there are only two call chains - one via die_if_kernel() and one
via do_page_fault(), both entering from die().  Both of these paths already
ensure that a kernel mode failure has happened.  Also, the original check
here, if (user_mode(regs)) was insufficient anyways, since it would not
rule out BUG faults from V8086 mode execution.

Saving the %ss segment in show_regs() rather than assuming a fixed value
also gives better information about the current kernel state in the
register dump.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some more assembler cleanups I noticed along the way.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Noticed by Chuck Ebbert: the .ldt entry of the TSS was set up incorrectly.
It never mattered since this was a leftover from old times, so remove it.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also, setting PDPEs in PAE mode does not require atomic operations, since the
PDPEs are cached by the processor, and only reloaded on an explicit or
implicit reload of CR3.

Since the four PDPEs must always be present in an active root, and the kernel
PDPE is never updated, we are safe even from SMIs and interrupts / NMIs using
task gates (which reload CR3).  Actually, much of this is moot, since the user
PDPEs are never updated either, and the only usage of task gates is by the
doublefault handler.  It appears the only place PGDs get updated in PAE mode
is in init_low_mappings() / zap_low_mapping() for initial page table creation
and recovery from ACPI sleep state, and these sites are safe by inspection.
Getting rid of the cmpxchg8b saves code space and 720 cycles in pgd_alloc on
P4.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Subtle fix: load_TLS has been moved after saving %fs and %gs segments to avoid
creating non-reversible segments.  This could conceivably cause a bug if the
kernel ever needed to save and restore fs/gs from the NMI handler.  It
currently does not, but this is the safest approach to avoiding fs/gs
corruption.  SMIs are safe, since SMI saves the descriptor hidden state.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

GCC can generate better code around descriptor update and access functions
when there is not an explicit "eax" register constraint.

Testing: You won't boot if this is messed up, since the TSS descriptor will be
corrupted.  Verified the assembler and booted.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

i386 inline assembler cleanup.

This change encapsulates descriptor and task register management.  Also,
it is possible to improve assembler generation in two cases; savesegment
may store the value in a register instead of a memory location, which
allows GCC to optimize stack variables into registers, and MOV MEM, SEG
is always a 16-bit write to memory, making the casting in math-emu
unnecessary.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

i386 arch cleanup.  Introduce the serialize macro to serialize processor
state.  Why the microcode update needs it I am not quite sure, since wrmsr()
is already a serializing instruction, but it is a microcode update, so I will
keep the semantic the same, since this could be a timing workaround.  As far
as I can tell, this has always been there since the original microcode update
source.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

i386 Inline asm cleanup.  Use cr/dr accessor functions.

Also, a potential bugfix.  Also, some CR accessors really should be volatile.
Reads from CR0 (numeric state may change in an exception handler), writes to
CR4 (flipping CR4.TSD) and reads from CR2 (page fault) prevent instruction
re-ordering.  I did not add memory clobber to CR3 / CR4 / CR0 updates, as it
was not there to begin with, and in no case should kernel memory be clobbered,
except when doing a TLB flush, which already has memory clobber.

I noticed that page invalidation does not have a memory clobber.  I can't find
a bug as a result, but there is definitely a potential for a bug here:

#define __flush_tlb_single(addr) \
	__asm__ __volatile__("invlpg %0": :"m" (*(char *) addr))
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes the vDSO use nops for all its padding around instructions,
rather than sometimes zeros, and nop-pads the end of the area containing
instructions to a 32-byte cache line, to keep text and data in separate
lines.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is subarch update for ES7000.  I've modified platform check code and
removed unnecessary OEM table parsing for newer systems that don't use OEM
information during boot.  Parsing the table in fact is causing problems,
and the platform doesn't get recognized.  The patch only affects the ES7000
subach.

Signed-off-by: <Natalie.Protasevich@unisys.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The VIA VT8237's IOAPIC sends 'APIC De-Assert Messages' by default, causing
another CPU interrupt when the IRQ pin is de-asserted.  This feature is
switched off by the patch to get rid of doubled ioapic level interrupt
rates.
Signed-off-by: NKarsten Wiese <annabellesgarden@yahoo.de>
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

i386 generic subarchitecture requires explicit dmi strings or command line
to enable bigsmp mode.  The patch below removes that restriction, and uses
bigsmp as soon as it finds more than 8 logical CPUs, Intel processors and
xAPIC support.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

o With introduction of kexec as boot-loader, the assumption that parameter
  segment will always be loaded at lower address than kernel and will be
  addressable by early bootup page tables is no longer valid. In kexec on
  panic case parameter segment might well be loaded beyond kernel image and
  might not be addressable by early boot page tables.
o This case might hit in the scenario where user has reserved a chunk of
  memory for second kernel, for example 16MB to 64MB, and has also built
  second kernel for physical memory location 16MB. In this case kexec has no
  choice but to load the parameter segment at a higher address than new kernel
  image at safe location where new kernel does not stomp it.
o Though problem should automatically go away once relocatable kernel for i386
  is in place and kexec can determine the location of new kernel at run time
  and load parameter segment at lower address than kernel image. But till then
  this patch can go in (assuming it does not break something else).
o This patch moves up the boot parameter saving code. Now boot parameters
  are copied out in protected mode before page tables are initialized. This
  will ensure that parameter segment is always addressable irrespective of
  its physical location.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If the virtual 86 machine reaches an instruction which raises a General
Protection Fault (such as CLI or STI), the instruction is emulated (in
handle_vm86_fault).  However, the emulation ignored the TF bit, so the
hardware debug interrupt was not invoked after such an emulated instruction
(and the DOS debugger missed it).

This patch fixes the problem by emulating the hardware debug interrupt as
the last action before control is returned to the VM86 program.
Signed-off-by: NPetr Tesarik <kernel@tesarici.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>