Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously.  Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We're still seeing a lot of issues with NCQ implementation in drive
firmwares.  Sprious FISes during NCQ command phase occur on many
drives and some of them seem potentially dangerous (at least to me).
Until we find the solution, spurious messages can give us more info.
Improve and limit them such that more info can be reported while not
disturbing users too much.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

vt6420 completely loses its ability to raise IRQ for ATAPI devices if
ATA_NIEN is diddled with in ->freeze.  Further investigation is
necessary to determine whether this problem is shared on other
controllers but it doesn't seem to be at this point.

Make vt6420's ->freeze only clear IRQ to fix this problem.  This makes
vt6420 relatively more prone to IRQ storms but the controller is way
too braindamaged to worry about that anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rather than ending up with two layers of negation jut rename the variable
and lose one.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix wrong checksum calculation on 64-bit MIPS
  [MIPS] VPE loader: Initialize lists before they're actually being used ...
  [MIPS] Fix reported amount of freed memory - it's in kB not bytes
  [MIPS] vr41xx: need one more nop with mtc0_tlbw_hazard()
  [MIPS] SMTC: Fix module build by exporting symbol
  [MIPS] SMTC: Fix TLB sizing bug for TLB of 64 >= entries
  [MIPS] Fix APM build
  [MIPS] There is no __GNUC_MAJOR__

Prevent the call to invalidate_inode_pages2() from racing with file writes
by taking the inode->i_mutex across the page cache flush and invalidate.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the Oops in http://bugzilla.linux-nfs.org/show_bug.cgi?id=138
We shouldn't be calling rpc_release_task() for tasks that are not active.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The commit 8e3d8433 ([NET]: MIPS
checksum annotations and cleanups) broke 64-bit MIPS.

The problem is the commit replaces some unsigned long with __be32.  On
64bit MIPS, a __be32 (i.e. unsigned int) value is represented as a
sign-extented 32-bit value in a 64-bit argument register.  So the
address 192.168.0.1 (0xc0a80001) is passed as 0xffffffffc0a80001 to
csum_tcpudp_nofold() but the asm code in the function expects
0x00000000c0a80001, therefore it returns a wrong checksum.  Explicit
cast to unsigned long is needed to drop high 32bit.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

kspd which due to makefile order happens to be initialized before the
vpe loader causes references to vpecontrol lists before they're actually
been initialized.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

While at it, change message on DEC for consistency.
Signed-off-by: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

NEC VR4111 and VR4121 need one more nop with mtc0_tlbw_hazard().
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Definitions for TIF_FREEZE and _TIF_FREEZE were missing.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Gcc major version number is in __GNUC__. As side effect fix checking
with sparse if sparse was built with gcc 4.1 and mips cross-compiler
is 3.4.

Sparse will inherit version 4.1, __GNUC__ won't be filtered from
"-dM -E -xc" output, sparse will pick only new major, effectively becoming
gcc version 3.1 which is unsupported.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Fix oops when Windows server sent bad domain name null terminator
  [CIFS]  cifs sprintf fix
  [CIFS] Remove 2 unneeded kzalloc casts
  [CIFS] Update CIFS version number

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
  [SCTP]: Fix compiler warning.
  [IP] TUNNEL: Fix to be built with user application.
  [IPV6]: Fixed the size of the netlink message notified by inet6_rt_notify().
  [TCP]: rare bad TCP checksum with 2.6.19
  [NET]: Process include/linux/if_{addr,link}.h with unifdef
  [NETFILTER]: Fix iptables ABI breakage on (at least) CRIS
  [IRDA] vlsi_ir.{h,c}: remove kernel 2.4 code
  [TCP]: skb is unexpectedly freed.
  [IPSEC]: Policy list disorder
  [IrDA]: Removed incorrect IRDA_ASSERT()
  [IrDA]: irda-usb TX path optimization (was Re: IrDA spams logfiles - since 2.6.19)
  [X.25]: Add missing sock_put in x25_receive_data
  [SCTP]: Fix SACK sequence during shutdown
  [SCTP]: Correctly handle unexpected INIT-ACK chunk.
  [SCTP]: Verify some mandatory parameters.
  [SCTP]: Set correct error cause value for missing parameters
  [NETFILTER]: fix xt_state compile failure
  [NETFILTER]: ctnetlink: fix leak in ctnetlink_create_conntrack error path
  [SELINUX]: increment flow cache genid
  [IPV6] MCAST: Fix joining all-node multicast group on device initialization.
  ...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  mv643xx_eth: Fix race condition in mv643xx_eth_free_tx_descs
  s2io bogus memset

Initialize qc->pad_len for each new command. This ensures
that pad_len is not set to a stale value for zero data
length commands.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some ATA/ATAPI devices act weirdly after the link is put into slumber
mode.  Some hang completely requiring physical power removal while
others fail to wake up till the link is hardreset a couple of times.

The addition of slumber on power down was never driven by real need.
It just followed what ahci spec said literally.  The spec itself seems
faulty in that it doesn't consider devices (not controllers) which
don't support link powersaving mode.

Theory never matches reality when it comes to dark allys of cheap
ATA/ATAPI world.  It's just unrealistic to expect vendors to test
rarely used link powersaving feature rigorously.  This patch makes
ahci more friendly to the coldness of reality.

This shouldn't have any negative effect - when suspend operation
succeeds, we power off the whole machine; otherwise, we wake up
everything.  I can't see any reason to be so elaborate with powering
down the link in the first place.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.

 From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.

This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As with JMicron controllers, ULi M5288 sets interface fatal error bit
on device error including ATAPI CC.  This makes libata hardreset the
port on ATAPI CC thus making it impossible to use.  Ignore interface
fatal error bit on ULi M5288.  This fixes bugzilla bug #7837.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

> --- a/net/sctp/sm_statefuns.c
> +++ b/net/sctp/sm_statefuns.c
> @@ -462,24 +461,6 @@ sctp_disposition_t sctp_sf_do_5_1C_ack(const struct sctp_endpoint *ep,

> -	if (!init_tag) {
> -		struct sctp_chunk *reply = sctp_make_abort(asoc, chunk, 0);
> -		if (!reply)
> -			goto nomem;

This introduced a compiler warning, easily fixed.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include/linux/if_tunnel.h is broken for user application
because it was changed to use __be32 which is required
to include linux/types.h in advance but didn't.

(This issue is found when building MIPL2 daemon. We are not sure this
is the last header to be fixed about __be32.)
Signed-off-by: NMasahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: NTAKAMIYA Noriaki <takamiya@po.ntts.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I think the return value of rt6_nlmsg_size() should includes the
amount of RTA_METRICS.
Signed-off-by: NNoriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch "Replace CHECKSUM_HW by CHECKSUM_PARTIAL/CHECKSUM_COMPLETE"
changed to unconditional copying of ip_summed field from collapsed
skb. This patch reverts this change.

The majority of substantial work including heavy testing
and diagnosing by: Michael Tokarev <mjt@tls.msk.ru>
Possible reasons pointed by: Herbert Xu and Patrick McHardy.
Signed-off-by: NJarek Poplawski <jarkao2@o2.pl>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit d3dcc077, 
include/linux/if_{addr,link}.h should be processed with unifdef.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the introduction of x_tables we accidentally broke compatibility
by defining IPT_TABLE_MAXNAMELEN to XT_FUNCTION_MAXNAMELEN instead of
XT_TABLE_MAXNAMELEN, which is two bytes larger.

On most architectures it doesn't really matter since we don't have
any tables with names that long in the kernel and the structure
layout didn't change because of alignment requirements of following
members. On CRIS however (and other architectures that don't align
data) this changed the structure layout and thus broke compatibility
with old iptables binaries.

Changing it back will break compatibility with binaries compiled
against recent kernels again, but since the breakage has only been
there for three releases this seems like the better choice.

Spotted by Jonas Berlin <xkr47@outerspace.dyndns.org>.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes kernel 2.4 compatibility code.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I encountered a kernel panic with my test program, which is a very
simple IPv6 client-server program.

The server side sets IPV6_RECVPKTINFO on a listening socket, and the
client side just sends a message to the server.  Then the kernel panic
occurs on the server.  (If you need the test program, please let me
know. I can provide it.)

This problem happens because a skb is forcibly freed in
tcp_rcv_state_process().

When a socket in listening state(TCP_LISTEN) receives a syn packet,
then tcp_v6_conn_request() will be called from
tcp_rcv_state_process().  If the tcp_v6_conn_request() successfully
returns, the skb would be discarded by __kfree_skb().

However, in case of a listening socket which was already set
IPV6_RECVPKTINFO, an address of the skb will be stored in
treq->pktopts and a ref count of the skb will be incremented in
tcp_v6_conn_request().  But, even if the skb is still in use, the skb
will be freed.  Then someone still using the freed skb will cause the
kernel panic.

I suggest to use kfree_skb() instead of __kfree_skb().
Signed-off-by: NMasayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent hashing introduced an off-by-one bug in policy list insertion.
Instead of adding after the last entry with a lesser or equal priority,
we're adding after the successor of that entry.

This patch fixes this and also adds a warning if we detect a duplicate
entry in the policy list.  This should never happen due to this if clause.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With USB2.0 bulk out MTU can be 512 bytes, so checking it only for 64
bytes is incorrect.
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we stop using dev_alloc_skb on the IrDA TX frame, we constantly run
into the case of the skb headroom being 0, and thus we call skb_cow for
every IrDA TX frame.
This patch uses a local buffer and memcpy the skb to it, saving us a
kmalloc for each of those IrDA TX frames.
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__x25_find_socket does a sock_hold.
This adds a missing sock_put in x25_receive_data.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when association enters SHUTDOWN state,the
implementation will SACK any DATA first and then transmit
the SHUTDOWN chunk.  This is against the order required by
2960bis spec.  SHUTDOWN must always be first, followed by
SACK. This change forces this order and also enables bundling.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>